Re: Unable up wlan0

Karl Relton escribi=F3:
> Eduardo
>
> Have you set your appropriate wireless network name, possible encryption
> key and so on in your /etc/network/interfaces file?
>   =

Yes, SinCables doesn't needs any encryption key, it's open, this is the
wlan0 section in /etc/network/interfaces:

allow-hotplug wlan0
iface wlan0 inet dhcp
   name Tarjeta de red inal=E1mbrica
   wireless_mode managed
   wireless-essid SinCables

this configuration was working before that i updated from version
0.2.4+svn20060808-1 to version 0.2.4+svn20060808-2,
> To get the 'link is not ready' message is normal - once the card is
> configured for the wireless network you want to be on, you then get
>
> ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
>   =

but now i can't up the link with any version :-(
> Karl
>   =

Thanks
Eduardo.


>
> On Sat, 2006-09-16 at 23:48 +0200, Eduardo wrote:
>   =

>> Hi, i'm running debian testing/unstable with custom kernel Linux 2.6.15,
>> i compiled the driver, with debian version 0.2.4+svn20060808-2, with
>> debug flag on, and loading...
>>
>> # modprobe  p80211 wlan_debug=3D5
>>
>> Sep  3 19:12:01 localhost kernel: init_module(0): ---->
>> Sep  3 19:12:01 localhost kernel: p80211netdev_startup(0): ---->
>> Sep  3 19:12:01 localhost kernel: p80211netdev_startup(0): <----
>>
>> #  modprobe prism2-cs prism2_debug=3D5
>>
>> Sep  3 19:12:01 localhost kernel: init_module(0): <----
>> Sep  3 19:12:05 localhost kernel: prism2cs_init(0): ---->
>> Sep  3 19:12:05 localhost kernel: prism2cs_init: prism2_cs.o: 0.2.4 Load=
ed
>> Sep  3 19:12:05 localhost kernel: prism2cs_init: dev_info is: prism2_cs
>> Sep  3 19:12:05 localhost kernel: prism2cs_init(0): <----
>>
>> and with the modules loaded i can see the proc information:
>>
>> # cat /proc/net/p80211/wlan0/wlandev
>> p80211 version: 0.2.4 (dom sep  3 18:14:03 CEST 2006)
>>
>> name       : wlan0
>> nsd name   : prism2_cs
>> address    : 00:02:6f:03:f2:6b
>> nsd caps   : wep_hw short_preamble hw_frag autojoin
>> bssid      : 00:00:00:00:00:00
>> Enabled    :
>>
>> # cat /proc/net/p80211/wlan0/nsd
>> # prism2_cs version 0.2.4 (dom sep  3 18:14:03 CEST 2006) '$Id:
>> prism2sta.c 1767 2006-01-19 21:25:50Z solomon $'
>>
>> # nic h/w: id=3D0x800c 1.0.0
>> # pri f/w: id=3D0x15 1.1.0
>> # sta f/w: id=3D0x1f 1.4.9
>> # initial nic hw type, needed for SSF ramdl
>> initnichw=3D0003
>>
>> I only get a "wlan0: link is not ready":
>>
>> ...
>> kernel: p80211knetdev_set_multicast_list(1): <----
>> kernel: p80211knetdev_get_stats(0): ---->
>> kernel: p80211knetdev_get_stats(0): <----
>> kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready
>> kernel: p80211knetdev_set_multicast_list(1): ---->
>> kernel: prism2sta_setmulticast(1): ---->
>> kernel: hfa384x_drvr_setconfig(1): ---->
>> ...
>>
>>
>> Anybody can helpme?
>>
>>
>> Thanks a lot
>> Eduardo.
>>
>> _______________________________________________
>> Linux-wlan-user mailing list
>> [email protected]
>> http://lists.linux-wlan.com/mailman/listinfo/linux-wlan-user
>>     =

>
>
>   =