Inappropriate ioctl for device: GET_DEVICE_ID on '/dev/usb/lp0' (Was setting up HP1020 laserjet printer)

Mandriva 2010.2, Gnome 2.30.0. A friend sold me an HP1020 the other day
but I'm having the devil of a time getting it to work. I've downloaded
foo2zjs, printed the install instructions and followed them to the
letter as far as I can tell. After running make I made sure to run
the ./getweb 1020 command. After running make install as root I ran make
install-hotplug, unplugged the printer and re-plugged it in. I ran make
cups also. I went into Mandrivas MCC and installed the printer and since
I have the printer connected to the usb port when setting up the printer
I tried both usb:/dev/usb/lp0, lp1 and usb://HP/LaserJet%201020 for the
URI. Then following the next direction I powered off and on the printer,
I did 'not' see any light flash orange to indicate the firmware was
being downloaded. Note: I also have an HP6L connected to a parallel port
so I also entered this line in my /etc/profile:

cat /usr/share/foo2zjs/firmware/sihp1020.dl > /dev/usb/lp0

I've checked and the lp0 or lp1 file is present in /dev/usb/. When
running the command # usb_printerid /dev/usb/lp0 to see if the firmware
is loaded I get:

Error: Inappropriate ioctl for device: GET_DEVICE_ID on '/dev/usb/lp0'

When trying to print a test document the printer icon on the task bar
says 'Printer HP LaserJet-1020 may not be connected'

I also see the below in my syslog:

Sep 25 15:54:37 localhost kernel: usb 5-7: new high speed USB device
using ehci_hcd and address 119
Sep 25 15:54:37 localhost kernel: usb 5-7: New USB device found,
idVendor=03f0, idProduct=2b17
Sep 25 15:54:37 localhost kernel: usb 5-7: New USB device strings:
Mfr=1, Product=2, SerialNumber=3
Sep 25 15:54:37 localhost kernel: usb 5-7: Product: HP LaserJet 1020
Sep 25 15:54:37 localhost kernel: usb 5-7: Manufacturer: Hewlett-Packard
Sep 25 15:54:37 localhost kernel: usb 5-7: SerialNumber: JL1F0DC
Sep 25 15:55:11 localhost kernel: usb 5-7: USB disconnect, address 119
Sep 25 15:55:13 localhost kernel: usb 5-7: new high speed USB device
using ehci_hcd and address 120
Sep 25 15:55:14 localhost kernel: usb 5-7: New USB device found,
idVendor=03f0, idProduct=2b17
Sep 25 15:55:14 localhost kernel: usb 5-7: New USB device strings:
Mfr=1, Product=2, SerialNumber=3
Sep 25 15:55:14 localhost kernel: usb 5-7: Product: HP LaserJet 1020
Sep 25 15:55:14 localhost kernel: usb 5-7: Manufacturer: Hewlett-Packard
Sep 25 15:55:14 localhost kernel: usb 5-7: SerialNumber: JL1F0DC
Sep 25 15:56:12 localhost kernel: parport_pc 00:0b: disabled
Sep 25 15:56:12 localhost kernel: IT8705 SuperIO detected.
Sep 25 15:56:12 localhost kernel: parport_pc 00:0b: activated
Sep 25 15:56:12 localhost kernel: parport_pc 00:0b: reported by Plug and
Play ACPI
Sep 25 15:56:12 localhost kernel: parport0: PC-style at 0x378, irq 7
[PCSPP,TRISTATE]
Sep 25 15:56:12 localhost kernel: parport0: Printer, Hewlett-Packard HP
LaserJet 6L
Sep 25 15:56:12 localhost kernel: ppdev: user-space parallel port driver
Sep 25 15:56:12 localhost kernel: lp0: using parport0
(interrupt-driven).
Sep 25 15:56:12 localhost kernel: lp0: console ready
Sep 25 15:56:13 localhost hp[14345]: io/hpmud/musb.c 2035: Invalid
usb_open: Permission denied
Sep 25 15:56:16 localhost python: io/hpmud/musb.c 2035: Invalid
usb_open: Permission denied
Sep 25 15:56:28 localhost kernel: Shorewall:net2fw:DROP:IN=eth0 OUT=
MAC=00:0f:ea:33:8f:ef:00:13:49:6e:55:07:08:00 SRC=192.168.2.1
DST=192.168.2.2 LEN=75 TOS=0x00 PREC=0x00 TTL=255 ID=4531 PROTO=UDP
SPT=161 DPT=53359 LEN=55

The shorewall line is puzzeling, it seems to show up I believe when I
try to print a document. I now have allowed port 161 in my firewall
setup.

I'm not sure what to do about these two lines either:

Sep 25 15:56:13 localhost hp[14345]: io/hpmud/musb.c 2035: Invalid
usb_open: Permission denied
Sep 25 15:56:16 localhost python: io/hpmud/musb.c 2035: Invalid
usb_open: Permission denied

If I log out and back in again and try to print a document I do not get
the printer disconnected error, however, If I turn it off and then on
again, trying to print shows 'the printer may not be connected'

Any advice/assistance would be appreciated.

-- 
Chris
KeyID 0xE372A7DA98E6705C
31.11°N 97.89°W (Elev. 1092 ft)
21:24:47 up 235 days, 3:04, 1 user, load average: 0.33, 0.33, 0.27

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)

iEYEABECAAYFAk5/43EACgkQ43Kn2pjmcFzl3gCdFoaa4z0ECtN1twm/y8P17ySO
F9EAnAlRE84T7vL3cSId4ZQXE08aNwPu
=GBxk
-----END PGP SIGNATURE-----