Re: ifconfig add -> resolver error

can u use netconf and add the desired ip and then restart the service may be
this should solve ur problem as u have not mentioned whether u want  to give
multiple ip addr. to single nic or just to change the current ip
I dont think DNS has something to do with this

----- Original Message -----
From: "Jason Pratt" <[email protected]>
To: <[email protected]>
Sent: Thursday, September 26, 2002 2:28 AM
Subject: ifconfig add -> resolver error


> Hi. I've been having an issue with ifconfig when adding an ip address.
> it goes like this:
>
> > ifconfig eth0 add 192.168.1.9
> > 192.168.1.9: Resolver Error 0 (no error)
>
> the current interface configuration is as follows:
>
> eth0      Link encap:Ethernet  HWaddr 00:02:55:9C:20:D1
>           inet addr:192.168.1.101  Bcast:192.168.1.255
> Mask:255.255.255.0
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:1666749 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:472 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:100
>           Interrupt:28 Base address:0x2080 Memory:f886e000-f886ec40
>
> eth1      Link encap:Ethernet  HWaddr 00:02:B3:5D:75:EA
>           inet addr:192.168.2.101  Bcast:192.168.2.255
> Mask:255.255.255.0
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:415752118 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:399736278 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:100
>           Interrupt:20 Base address:0x3000 Memory:f8870000-f8870c40
>
> eth1:0    Link encap:Ethernet  HWaddr 00:02:B3:5D:75:EA
>           inet addr:192.168.2.100  Bcast:192.168.2.255
> Mask:255.255.255.0
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           Interrupt:20 Base address:0x3000 Memory:f8870000-f8870c40
>
> eth2      Link encap:Ethernet  HWaddr 00:02:B3:5D:75:EB
>           inet addr:192.168.3.101  Bcast:192.168.3.255
> Mask:255.255.255.0
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:2251714 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:3478172 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:100
>           Interrupt:21 Base address:0x3040 Memory:f8872000-f8872c40
>
> lo        Link encap:Local Loopback
>           inet addr:127.0.0.1  Mask:255.0.0.0
>           UP LOOPBACK RUNNING  MTU:3924  Metric:1
>           RX packets:275 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:275 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:0
>
>
> routing looks like this:
>
> Kernel IP routing table
> Destination     Gateway         Genmask         Flags Metric Ref    Use
> Iface
> 192.168.1.101   0.0.0.0         255.255.255.255 UH    0      0        0
> eth0
> 192.168.3.101   0.0.0.0         255.255.255.255 UH    0      0        0
> eth2
> 192.168.2.100   0.0.0.0         255.255.255.255 UH    0      0        0
> eth1
> 192.168.2.101   0.0.0.0         255.255.255.255 UH    0      0        0
> eth1
> 192.168.3.0     0.0.0.0         255.255.255.0   U     0      0        0
> eth2
> 192.168.2.0     0.0.0.0         255.255.255.0   U     0      0        0
> eth1
> 192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0
> eth0
> 127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0
> lo
> 0.0.0.0         192.168.1.1     0.0.0.0         UG    0      0        0
> eth0
>
>
>
> the nameserver in resolv.conf is reachable and working correctly. not
> sure what else to include. ifconfig is the version 1.54 supplied with
> the release. let me know if you can help!
>
> ::ja
>
>
>
> _______________________________________________
> Zoot-list mailing list
> [email protected]
> https://listman.redhat.com/mailman/listinfo/zoot-list
>