Re: SUSE9.3 and Terratec Cinergy 400

On Sunday 08 May 2005 17:13, you wrote:
> > I run SUSE9.3 and I use the TV card from Terratec Cinergy 400.
> > Through YAST the card is detected but when I scan the channels nothing is
> > being found.
> > In the syslog I have the below listed entries
> >
> > Does anybode know what is wrong here and how can I fix it?
> >
> > May  8 16:44:29 apus kernel: saa7133[0]: found at 0000:03:00.0, rev: 240,
> > irq: 10, latency: 0, mmio: 0x40800000
> > May  8 16:44:29 apus kernel: PCI: Setting latency timer of device
> > 0000:03:00.0 to 64
> > May  8 16:44:29 apus kernel: saa7133[0]: subsystem: 153b:1162, board:
> > Terratec Cinergy 400 TV [card=8,insmod option]
> > May  8 16:44:29 apus kernel: saa7133[0]: board init: gpio is 40000
> > May  8 16:44:29 apus kernel: saa7133[0]: registered input device for IR
> > May  8 16:44:29 apus kernel: saa7133[0]: dsp access wait timeout
> > [bit=WRR] May  8 16:44:29 apus kernel: saa7133[0]: dsp access wait
> > timeout [bit=WRR] May  8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 00:
> > 3b 15 62 11 08 20 1c 55 43 43 a9 1c 55 43 43 a9
> > May  8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 10: 00 ff e6 07 00 00
> > 00 00 00 00 00 00 00 00 00 00
> > May  8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 20: 01 00 02 02 01 3e
> > 9b cb 91 03 03 00 07 00 01 00
> > May  8 16:44:30 apus kernel: saa7133[0]: i2c eeprom 30: 00 02 02 00 00 00
> > 00 00 00 00 00 00 00 00 00 00
> > May  8 16:44:30 apus modprobe: FATAL: Error inserting tuner
> > (/lib/modules/2.6.11.4-20a-default/kernel/drivers/media/video/tuner.ko):
> > Unknown symbol in module, or unknown parameter (see dmesg)
> > May  8 16:44:30 apus kernel: tuner: Unknown parameter `tuner'
> > May  8 16:44:30 apus kernel: load_module: err 0xfffffffe (dont worry)
> > May  8 16:44:30 apus kernel: saa7133[0]: registered device video0 [v4l2]
> > May  8 16:44:30 apus kernel: saa7133[0]: registered device vbi0
> >
> > --
> > Any help is very much appreciated.
> > Sami
>
> Which tuner did you have YAST assign to the card, TV video processing
> chip and tuner are two seperate items.
If I try to select a tuner under terratec cinergy 400 it says there is no 
tuner available? Which one do I have to select?

--
Thanks for your help
Sami