RE: Iomega Ditto Easy 800 not detected by bpck-fdc (2)

Smed,
	Can you provide the sequence that you loaded the modules and any of
the parameter associated with each module?  I get similar errors to just
about everyone that can't get their Ditto Easy 800 loaded.

Kevin Foss
Ottawa, Canada

-----Original Message-----
From: smed [mailto:[email protected]]
Sent: Friday, 21 June, 2002 12:16
To: [email protected]
Subject: Re: Iomega Ditto Easy 800 not detected by bpck-fdc (2)



I recently got my Ditto 800 working with the linux 2.2.19 kernel.
I had to recompile about a bagillion times.
Try loading all the modules in sequence.
don't build the parport and parport_pc modules into the kernel...load them
seperately
and make sure and setup the appropriate parameters in /etc/modules.conf
don't load the ftape-compressor....it's not needed.

I honestly don't know how I got it to work, however I know I had to
recompile the
kernel and the modules nearly a dozen times.

I'm still working on another colorodo trakker 250 tape drive that I can not
get to
work.  I'm thinking of upgrading to a 2.2 kernel just to see if the support
is better.

smed



On Fri, Jun 21, 2002 at 05:53:06PM +0200, Alessio Martini wrote:
> [follows from the previous message]
> 
> I also discovered that I obtain the same error message both when the 
> parallel cable is plugged and when it's unplugged. The problem is not the 
> cable, since I can print to a printer which is connected through the
Iomega 
> Ditto drive.
> Moreover, it doesn't matter if parport and/or parport_pc modules are 
> loaded: I always get the same error message in /var/log/messages:
> 
> Jun 21 00:06:26 due kernel: bpck-fdc.c: bpck_fdc_register @ 0xd291cce0
> Jun 21 00:06:26 due kernel: [005]     bpck-fdc.c (bpck_fdc_query_proto) - 
> Got 0xf8, expected either 0xc0 or 0x40.
> Jun 21 00:06:26 due kernel: [006] 0 bpck-fdc.c (bpck_fdc_detect) - can't 
> find bpck interface for ftape id 0.
> Jun 21 00:06:26 due kernel: [007] 0 bpck-fdc.c (bpck_fdc_detect) - 
> ft_parport_probe(fdc, &bpck->parinfo) failed: -6.
> 
> Alessio Martini
> 
> 
> 
> Alessio Martini
> Piazza del Rosario, 9
> 28922 Verbania Pallanza (VB)
> Italy
> 
> Tel.: +39-0323-503071
> e-mail: [email protected]
> 
> 
> -
> To unsubscribe from this list: send the line "unsubscribe linux-tape" in
> the body of a message to [email protected]
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
-
To unsubscribe from this list: send the line "unsubscribe linux-tape" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
-
To unsubscribe from this list: send the line "unsubscribe linux-tape" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html