Media_Wearout_Indicator not working on Intel 520 SSD
| Newsgroups | gmane.linux.utilities.smartmontools |
|---|---|
| Message-ID | <[email protected]> |
Hello, I have dire problems making my Intel 520 SSD report anything meaningful in terms of wear and tear. Media_Wearout_Indicator stays at "100" even after a year of extensive use in a server and Power_On_Hours shows "74285755253828" as the raw value. I'm attaching the output of "smartctl -a /dev/sda" below. I'm running Debian. Thank you! -------------------- smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: INTEL SSDSC2CW120A3 Serial Number: CVCV24810478120BGN Firmware Version: 400i User Capacity: 120,034,123,776 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Not recognized. Minor revision code: 0x0110 Local Time is: Mon Mar 10 12:22:27 2014 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (2097) seconds. Offline data collection capabilities: (0x7f) SMART execute Offline immediate. Auto Offline data collection on/off support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0021) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 5 Reallocated_Sector_Ct 0x0032 100 100 000 Old_age Always - 0 9 Power_On_Hours 0x0032 000 000 000 Old_age Always - 74285755253828 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 7 170 Unknown_Attribute 0x0033 100 100 010 Pre-fail Always - 0 171 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 172 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 174 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 7 184 End-to-End_Error 0x0033 100 100 090 Pre-fail Always - 0 187 Reported_Uncorrect 0x000f 106 106 050 Pre-fail Always - 12970489 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 7 225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 398615 226 Load-in_Time 0x0032 100 100 000 Old_age Always - 65535 227 Torq-amp_Count 0x0032 100 100 000 Old_age Always - 0 228 Power-off_Retract_Count 0x0032 100 100 000 Old_age Always - 65535 232 Available_Reservd_Space 0x0033 100 100 010 Pre-fail Always - 0 233 Media_Wearout_Indicator 0x0032 100 100 000 Old_age Always - 0 241 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 398615 242 Total_LBAs_Read 0x0032 100 100 000 Old_age Always - 1152 249 Unknown_Attribute 0x0013 100 100 000 Pre-fail Always - 9987 SMART Error Log Version: 0 No Errors Logged SMART Self-test log structure revision number 0 Warning: ATA Specification requires self-test log structure revision number = 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. ------------------------------------------------------------------------------ Learn Graph Databases - Download FREE O'Reilly Book "Graph Databases" is the definitive new guide to graph databases and their applications. Written by three acclaimed leaders in the field, this first edition is now available. Download your free book today! http://p.sf.net/sfu/13534_NeoTech