Re: Mediasonic 8 Bay External Hard Drive Enclosure connected via USB 3.0
Graham Fleming <[email protected]>
| Newsgroups | gmane.linux.utilities.smartmontools |
|---|---|
| Message-ID | <[email protected]> |
So, now that my smartd.conf file is working again (I didn't ever re-write it for the -d sat command), I'm seeing some errors come up when I restart smartd.
Here's an example of one of the drives in the 8-bay array (all drives report same error):
smartd[12997]: Device: /dev/sdi [SAT], ST1000NM0011, S/N:Z1N0APEA, WWN:5-000c50-03ec3daa1, FW:PA07, 1.00 TB
smartd[12997]: Device: /dev/sdi [SAT], found in smartd database: Seagate Constellation ES (SATA 6Gb/s)
smartd[12997]: Device: /dev/sdi [SAT], not capable of SMART Health Status check
smartd[12997]: Device: /dev/sdi [SAT], is SMART capable. Adding to "monitor" list.
smartd[12997]: Device: /dev/sdj [SAT], opened
Not sure exactly what SMART Health Status check is, but when I run smartctl -a on that drive, everything seems pretty good:
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.15.5-1-ARCH] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
Jul 16 09:35:27 Mediacentre sudo[13352]: pam_unix(sudo:session): session opened for user root by (uid=0)
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST1000NM0011
Serial Number: Z1N0APEA
LU WWN Device Id: 5 000c50 03ec3daa1
Add. Product Id: DELL(tm)
Firmware Version: PA07
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Jul 16 09:35:27 2014 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART STATUS RETURN: incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 080 063 044 Pre-fail Always - 112875577
3 Spin_Up_Time 0x0003 095 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 20
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 076 060 030 Pre-fail Always - 42348384
9 Power_On_Hours 0x0032 081 081 000 Old_age Always - 16909
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 18
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 060 049 045 Old_age Always - 40 (Min/Max 37/49)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 13
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 21
194 Temperature_Celsius 0x0022 040 051 000 Old_age Always - 40 (0 18 0 0 0)
195 Hardware_ECC_Recovered 0x001a 116 099 000 Old_age Always - 112875577
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 161048388714742
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 349799315
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1194316266
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 15625 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
On Jul 15, 2014, at 10:34 PM, Christian Franke <[email protected]> wrote:
> Graham Fleming wrote:
>> idVendor 0x152d JMicron Technology Corp. / JMicron USA Technology Corp.
>> idProduct 0x0539 JMS539 SuperSpeed SATA II 3.0G Bridge
>> bcdDevice 28.12
>
> Added to drivedb.h in r3950, r3951. Please run /usr/sbin/update-smart-drivedb. Should work without "-d sat" then.
>
> Thanks,
> Christian
>
------------------------------------------------------------------------------
Want fast and easy access to all the code in your enterprise? Index and
search up to 200,000 lines of code with a free copy of Black Duck
Code Sight - the same software that powers the world's largest code
search on Ohloh, the Black Duck Open Hub! Try it now.
http://p.sf.net/sfu/bds