[WBEL-users] panic in WBEL4?
david <[email protected]> Tue, 18 Jul 2006 18:13:34 -0700
| Newsgroups | gmane.linux.whitebox.user |
|---|---|
| Message-ID | <[email protected]> |
Dear Friends I'm getting 4 to 5 panics per day on my computer. Most of them produce an reboot (because I have the Kernel parameter "panic=10"), but not all do. I have been sitting next to the computer when this happens, and the frame, power supply and everything else feels cool to the touch, so I don't think it's a heat problem. Specifics of my configuration: WBEL4 updated as of 17 July 2006 Applications are - mail, http, dns and ftp servers The system also provides routing functions (NAT) to my home windows computers. 512M of memory two NIC's Command line interface only (no graphic stuff installed) Two HDs (80, 120) combined as a single logical volume Anything else you need to know? The failures that I've been able to see mostly say "spinlock" or something similar, but it's pure luck if I see the failure. I've tried two memory modules (pc2100 ddr, and pc2700 ddr) and both produce similar failures. Do I have a bad CPU? Bad memory? Bad drives? Bad Linux? HELP I have enclosed a copy of the "dmsg" output after a boot, maybe there's something there I haven't noticed. I converted it to cr-lf notation in case you are reading with windows. _______________________________________________ Whitebox-users mailing list [email protected] http://beau.org/mailman/listinfo/whitebox-users
dmesg.txt
(text/plain, 14 KB)
Linux version 2.6.9-34.0.1.EL ([email protected]) (gcc version 3.4.5 20051201 (Red Hat 3.4.5-2)) #1 Wed May 24 22:44:24 CDT 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) BIOS-e820: 00000000fefffc00 - 00000000ff000000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. Using x86 segment limits to approximate NX protection zapping low mappings. On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126960 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 Nvidia ) @ 0x000f6ca0 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7d80 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x4008 Built 1 zonelists Kernel command line: ro root=/dev/VolGroup00/LogVol00 panic=10 Initializing CPU#0 CPU 0 irqstacks, hard=c03e7000 soft=c03e6000 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 1808.581 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 514360k/524224k available (2118k kernel code, 9296k reserved, 668k data, 144k init, 0k highmem) Calibrating delay using timer specific routine.. 3619.98 BogoMIPS (lpj=1809994) Security Scaffold v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode There is already a security framework initialized, register_security failed. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 078bf3ff e1d3fbff 00000000 00000010 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Sempron(tm) Processor 3100+ stepping 00 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ACPI: IRQ9 SCI: Edge set to Level Trigger. checking if image is initramfs... it is Freeing initrd memory: 980k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfb9f0, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040816 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: Power Resource [ISAV] (on) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 *12 14 15) ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled. ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled. ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled. ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled. ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled. ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing ACPI: PCI Interrupt Link [LSMB] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 3 ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 3 (level, low) -> IRQ 3 ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 3 ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 3 (level, low) -> IRQ 3 ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 3 ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 3 (level, low) -> IRQ 3 ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt Link [LACI] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 12 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 12 (level, low) -> IRQ 12 ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 11 ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 11 (level, low) -> IRQ 11 PCI: Device 00:28 not found by BIOS apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1153269823.633:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key 1CB5000E9E8CBA55 - User ID: White Box (Kernel Module GPG key) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Fan [FAN] (on) ACPI: Processor [CPU0] (supports C1) ACPI: Thermal Zone [THRM] (40 C) Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected AGP bridge 0 agpgart: Setting up Nforce3 AGP. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 128M @ 0xd0000000 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize divert: not allocating divert_blk for non-ethernet device lo Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE3-250: IDE controller at PCI slot 0000:00:08.0 NFORCE3-250: chipset revision 162 NFORCE3-250: not 100% native mode: will probe irqs later NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: Maxtor 6Y080L0, ATA DISK drive Using cfq io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HDS722516VLAT80, ATA DISK drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... hda: max request size: 128KiB hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133) hda: cache flushes supported hda: hda1 hda2 hdc: max request size: 1024KiB hdc: 321672960 sectors (164696 MB) w/7938KiB Cache, CHS=20023/255/63, UDMA(100) hdc: cache flushes supported hdc: hdc1 ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 NET: Registered protocol family 2 IP: routing cache hash table of 1024 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 9362) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI: (supports S0 S3 S4 S5) ACPI wakeup devices: SLPB HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1 Freeing unused kernel memory: 144k freed device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [email protected] EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: dm-0: orphan cleanup on readonly fs ext3_orphan_cleanup: deleting unreferenced inode 2146311 ext3_orphan_cleanup: deleting unreferenced inode 2146309 ext3_orphan_cleanup: deleting unreferenced inode 2146308 EXT3-fs: dm-0: 3 orphan inodes deleted EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks SCSI subsystem initialized libata version 1.20 loaded. inserting floppy driver for 2.6.9-34.0.1.EL Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.41. ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:05.0 to 64 divert: allocating divert_blk for eth0 eth0: forcedeth.c: subsystem: 01019:2501 bound to 0000:00:05.0 epic100.c:v1.11 1/7/2001 Written by Donald Becker <[email protected]> http://www.scyld.com/network/epic100.html (unofficial 2.4.x kernel port, version 1.11+LK1.1.14+AC1.1.14, June 2, 2004) ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 11 (level, low) -> IRQ 11 epic100(0000:02:06.0): ***WARNING***: No MII transceiver found! divert: allocating divert_blk for eth1 eth1: SMSC EPIC/100 83c170 at 0xc000, IRQ 11, 00:e0:29:07:10:94. ip_tables: (C) 2000-2002 Netfilter core team eth0: no link during initialization. ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:06.0 to 64 intel8x0_measure_ac97_clock: measured 50047 usecs intel8x0: clocking to 46797 shpchp: shpc_init : shpc_cap_offset == 0 shpchp: shpc_init : shpc_cap_offset == 0 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 3 (level, low) -> IRQ 3 ehci_hcd 0000:00:02.2: EHCI Host Controller PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: irq 3, pci mem e08e8000 ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1 PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 3 (level, low) -> IRQ 3 ohci_hcd 0000:00:02.0: OHCI Host Controller PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: irq 3, pci mem e08ea000 ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 3 (level, low) -> IRQ 3 ohci_hcd 0000:00:02.1: OHCI Host Controller PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: irq 3, pci mem e08ec000 ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected eth0: link up. md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] EXT3 FS on dm-0, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 1048568k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 parport0: PC-style at 0x378 [PCSPP,TRISTATE] ip_conntrack version 2.1 (4095 buckets, 32760 max) - 356 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team NET: Registered protocol family 10 Disabled Privacy Extensions on device c0378f60(lo) IPv6 over IPv4 tunneling driver divert: not allocating divert_blk for non-ethernet device sit0 parport0: PC-style at 0x378 [PCSPP,TRISTATE] lp0: using parport0 (polling). lp0: console ready eth0: no IPv6 routers present eth1: no IPv6 routers present