Re: Configuration need in order to recieve snmp traps

Hello Mr.Vinod,

No, It is not working after this also

Please clarify one thing in order to recieve traps from an snmp device is it necessary to have mib file of that device

I only need to recieve traps that is enough

After i complete the steps given by you I am getting the below mentioned output

Warning : -P option is depricated; use -f -Le instead
Cannot find module (TRAP-TEST-MIB) : At line 0 in (none)

/usr/local/share/snmp/snmptrapd.conf:line 38 : Error : Bad trap OID in traphandler directive: TRAP-TEST-MIB::demo-trap

net-snmp: 1 error(s) in config file(s)

Warning : no access control information configured.

This reciever will *NOT* accept any incomming notifications.

NET-SNMPversion 5.3.0.1

coudn't open udp:162 -- errno 98 (" Address already in use ")





Thanks & Regards,
 
Santhosh Kumar Suddavanda

Mail :  [email protected]

  ----- Original Message ----- 
  From: [email protected] 
  To: [email protected] 
  Sent: Monday, April 24, 2006 1:12 PM
  Subject: RE: Configuration need in order to recieve snmp traps


  Hi

  Please create the following directory

    /usr/local/etc/snmp

    And create a file called snmptrapd.conf

    Place the following content into it

     

  authCommunity   log,execute,net         public

   

  Then try the snmptrapd -P command, it works now.

    Check that and let me know whether it is sending traps.

  Regards

  Vinod

   

   


------------------------------------------------------------------------------

  From: [email protected] [mailto:[email protected]] On Behalf Of santhosh
  Sent: Monday, April 24, 2006 12:28 PM
  To: net-snmp-users
  Subject: Configuration need in order to recieve snmp traps

   

   

    

  Hello all,

   

  I am able to communicate with the snmp device which i am having but not able to recieve the traps generated by the device

   

  In the FAQ I have seen that in order to recieve snmp traps I need to configure snmptrapd 

   

  But it is not working 

   

  I am getting the error given below

   

  No log handling enabled - turning on stderr logging

  Cannot find module (TRAP-TEST-MIB) : At line 0 in (none)

  /usr/local/share/snmp/snmptrapd.conf:line 38 : Error : Bad trap OID in traphandler directive: TRAP-TEST-MIB::demo-trap

  net-snmp: 1 error(s) in config file(s)

  Warning : no access control information configured.

  This reciever will *NOT* accept any incomming notifications.

   

  I am looking out for solution

  It seems to be that the snmptrad.conf is not correct

  in order to recieve a trap message from 192.168.1.50 device 

  what is the configuration to be needed

   

  thanks in advance

   

  looking for result ASA

   


   
  Thanks & Regards,
   
  Santhosh Kumar Suddavanda

  Mail :  [email protected]


        The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain proprietary, confidential or privileged information. If you are not the intended recipient, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately and destroy all copies of this message and any attachments. 

        WARNING: Computer viruses can be transmitted via email. The recipient should check this email and any attachments for the presence of viruses. The company accepts no liability for any damage caused by any virus transmitted by this email.

        www.wipro.com
       



------------------------------------------------------------------------------


  No virus found in this incoming message.
  Checked by AVG Free Edition.
  Version: 7.1.385 / Virus Database: 268.4.5/322 - Release Date: 4/22/06