Re: can we combine lm-sensors with snmp??

Thanks for the response. I have check using

snmpwalk -v1 -c public localhost UCD-SNMP-MIB::ucdavis

and then, the data from lm-sensors is displayed, like this :

LM-SENSORS-MIB::lmTempSensorsIndex.1 = INTEGER: 0
LM-SENSORS-MIB::lmTempSensorsIndex.2 = INTEGER: 1
LM-SENSORS-MIB::lmTempSensorsDevice.1 = STRING: CPU Temp
LM-SENSORS-MIB::lmTempSensorsDevice.2 = STRING: Int Temp
LM-SENSORS-MIB::lmTempSensorsValue.1 = Gauge32: 27425
LM-SENSORS-MIB::lmTempSensorsValue.2 = Gauge32: 45000
LM-SENSORS-MIB::lmFanSensorsIndex.1 = INTEGER: 0
LM-SENSORS-MIB::lmFanSensorsIndex.2 = INTEGER: 1
LM-SENSORS-MIB::lmFanSensorsDevice.1 = STRING: Case Fan
LM-SENSORS-MIB::lmFanSensorsDevice.2 = STRING: CPU Fan
LM-SENSORS-MIB::lmFanSensorsValue.1 = Gauge32: 0
LM-SENSORS-MIB::lmFanSensorsValue.2 = Gauge32: 0
LM-SENSORS-MIB::lmVoltSensorsIndex.1 = INTEGER: 0
LM-SENSORS-MIB::lmVoltSensorsIndex.2 = INTEGER: 1
LM-SENSORS-MIB::lmVoltSensorsIndex.3 = INTEGER: 2
LM-SENSORS-MIB::lmVoltSensorsIndex.4 = INTEGER: 3
LM-SENSORS-MIB::lmVoltSensorsIndex.5 = INTEGER: 4
LM-SENSORS-MIB::lmVoltSensorsIndex.6 = INTEGER: 5
LM-SENSORS-MIB::lmVoltSensorsDevice.1 = STRING: +3.3V
LM-SENSORS-MIB::lmVoltSensorsDevice.2 = STRING: +2.5V
LM-SENSORS-MIB::lmVoltSensorsDevice.3 = STRING: VCore
LM-SENSORS-MIB::lmVoltSensorsDevice.4 = STRING: +5V
LM-SENSORS-MIB::lmVoltSensorsDevice.5 = STRING: +12V
LM-SENSORS-MIB::lmVoltSensorsDevice.6 = STRING: +3.3V
LM-SENSORS-MIB::lmVoltSensorsValue.1 = Gauge32: 3366
LM-SENSORS-MIB::lmVoltSensorsValue.2 = Gauge32: 2480
LM-SENSORS-MIB::lmVoltSensorsValue.3 = Gauge32: 1032
LM-SENSORS-MIB::lmVoltSensorsValue.4 = Gauge32: 4708
LM-SENSORS-MIB::lmVoltSensorsValue.5 = Gauge32: 11901
LM-SENSORS-MIB::lmVoltSensorsValue.6 = Gauge32: 3298
LM-SENSORS-MIB::lmMiscSensorsIndex.1 = INTEGER: 0
LM-SENSORS-MIB::lmMiscSensorsIndex.2 = INTEGER: 1
LM-SENSORS-MIB::lmMiscSensorsIndex.3 = INTEGER: 2
LM-SENSORS-MIB::lmMiscSensorsDevice.1 = STRING: alarms
LM-SENSORS-MIB::lmMiscSensorsDevice.2 = STRING: vid
LM-SENSORS-MIB::lmMiscSensorsDevice.3 = STRING: vrm
LM-SENSORS-MIB::lmMiscSensorsValue.1 = Gauge32: 4608000
LM-SENSORS-MIB::lmMiscSensorsValue.2 = Gauge32: 1750
LM-SENSORS-MIB::lmMiscSensorsValue.3 = Gauge32: 1699


is it rigth? But, when i check using snmpwalk -v1 -c public localhost,
LM-SENSORS MIB not appear.
So, when i check using OpenNMS (network management software), only SNMP node
data, SNMP Interface Data, Storage, Disk Table Index that appear, but no
UCD-SNMP for LM-SENSORS appear. Any hints?
Thanks.

2008/6/13 Thomas Anders <[email protected]>:

> komang adi wrote:
> > when i check using net-snmp --snmpd-module-list, it is stated that
> > ucd-snmp/lmSensors, it mean that lm-sensors have already compile yet?
> > But when i check using snmpwalk -v1 -c public localhost, there is no
> > data for lmSensor, how can i check snmp have collected data from
> > lm-sensors?
>
> http://www.net-snmp.org/wiki/index.php/FAQ:Applications_06
>
>
> +Thomas
>
> --
> Thomas Anders (thomas.anders at blue-cable.de)
>

-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://sourceforge.net/services/buy/index.php

_______________________________________________
Net-snmp-users mailing list
[email protected]
Please see the following page to unsubscribe or change other options:
https://lists.sourceforge.net/lists/listinfo/net-snmp-users