Hi :) need help for configuration of snmpd.conf

###########################################################################
#
# snmpd.conf
#
#   - created by the snmpconf configuration program
#
###########################################################################
# SECTION: Access Control Setup
#
#   This section defines who is allowed to talk to your running
#   snmp agent.

# rouser: a SNMPv3 read-only user
#   arguments:  user [noauth|auth|priv] [restriction_oid]

rouser    

# rwcommunity: a SNMPv1/SNMPv2c read-write access community name
#   arguments:  community [default|hostname|network/bits] [oid]

rwcommunity  private localhost 
rwcommunity  test 127.0.0.1
rwcommunity  test2 192.168.0.1
rwcommunity  test3 192.168.0.2

#MIB directories. /usr/share/snmp/mibs is the default, 
#including it here avoids some strange problems
export MIBDIRS=/usr/share/snmp/mibs

#snmpd control (yes means start deamon
SNMPDRUN=yes

#snmpd options (use syslog,close stdin/out/err)
SNMPDOPTS='-Lsd -Lf /dev/null -u snmp -g snmp -I -smux -p /var/run/snmpd.pid 198.168.0.1'



###########################################################################
# SECTION: Trap Destinations
#
#   Here we define who the agent will send traps to.

# trapsink: A SNMPv1 trap receiver
#   arguments: host [community] [portnum]

trapsink  private 

# trapcommunity: Default trap sink community to use
#   arguments: community-string

trapcommunity  private



###########################################################################
# SECTION: Agent Operating Mode
#
#   This section defines how the agent will operate when it
#   is running.

# master: Should the agent operate as a master agent or not.
#   Currently, the only supported master agent type for this token
#   is "agentx".
#   
#   arguments: (on|yes|agentx|all|off|no)

master  no

# agentuser: The system user that the agent runs as.
#   arguments: name|#uid

agentuser  manager

# agentgroup: The system group that the agent runs as.
#   arguments: group|#GID

agentgroup  

# agentaddress: The IP address and port number that the agent will listen on.
#   By default the agent listens to any and all traffic from any
#   interface on the default SNMP port (161).  This allows you to
#   specify which address, interface, transport type and port(s) that you
#   want the agent to listen on.  Multiple definitions of this token
#   are concatenated together (using ':'s).
#   arguments: [transport:]port[@interface/address],...

agentaddress udp:161


###########################################################################
# SECTION: Extending the Agent
#
#   You can extend the snmp agent to have it return information
#   that you yourself define.

# exec: run a simple command using exec()
#   arguments:  [oid] name /path/to/executable arguments

exec     
exec     



###########################################################################
# SECTION: Monitor Various Aspects of the Running Host
#
#   The following check up on various aspects of a host.

# proc: Check for processes that should be running.
#     proc NAME [MAX=0] [MIN=0]
#   
#     NAME:  the name of the process to check for.  It must match
#            exactly (ie, http will not find httpd processes).
#     MAX:   the maximum number allowed to be running.  Defaults to 0.
#     MIN:   the minimum number to be running.  Defaults to 0.
#   
#   The results are reported in the prTable section of the UCD-SNMP-MIB tree
#   Special Case:  When the min and max numbers are both 0, it assumes
#   you want a max of infinity and a min of 1.

proc    



###########################################################################
# SECTION: System Information Setup
#
#   This section defines some of the information reported in
#   the "system" mib group in the mibII tree.

# syslocation: The [typically physical] location of the system.
#   Note that setting this value here means that when trying to
#   perform an snmp SET operation to the sysLocation.0 variable will make
#   the agent return the "notWritable" error code.  IE, including
#   this token in the snmpd.conf file will disable write access to
#   the variable.
#   arguments:  location_string

syslocation