RE: Wiring folks out there?

Well, it's an older house.  The four drops are in three vastly different
areas of the house.  Two of the drops are in proximity to each other, but
probably 15 feet away from each other.

Plenum sounds like the way to go, although costly.

As this is a bit out of my league, if someone would be interested in talking
to me offline about doing this job for me, costs associated with it, I would
appreciate it.

Thanks.

Mike Strock
[email protected]
http://www.myhomeoffice.org/ - New pictures of my kids here!


-----Original Message-----
From: [email protected]
[mailto:[email protected]]On Behalf Of Orion
Sent: Monday, March 21, 2005 7:23 AM
To: SeattleWireless Talk List
Cc: [email protected]
Subject: RE: Wiring folks out there?


If you're going to run the wiring neatly (ie fished through the walls, etc)
the biggest hang up may be the transition through the floor on the upstairs,
and the transition through the ground floor into the basement - you're
either going to have to drill to get the cable runs through, or find points
where the piping goes through and squeeze it through in parallel.

An easier approch would be to run a single bundle from the basement to the
crawlspace in the the 2nd floor ceiling (or attic if you actually have one),
then from there fish it down inside the walls to each room. You could either
install an outdoor conduit and run the cables fromt he basement, out and up,
or if you can find where the piping etc goes through the floors and up, even
better (that way everything stays inside).

2 notes of caution (1 goes without saying, but):

1) Stay away from the electrical wiring with your CAT-5 runs.  Not just for
safety, but if your runs are within 6" or so of AC wiring and run parallel
to it for any length, the AC resonance can wreak havoc on data integrity.

2) You are running through walls in a residence. Do yourself (and your
family) a favor and pay the extra for the Plenum.  It's worth it for safety.

/Alex K.

On Mon, 21 Mar 2005 00:34:47 -0800, Ian Pierce wrote
> You shouldn't need shielded cable.  UTP, or Unshielded Twisted Pair,
> should work just fine.  I suppose if you're going through the walls
> and you want to make the fire marshall happy you'll want cable that
> is plenum rated, which costs about 4x as much as regular UTP.
>
> As for the cost, I can't help you there, I usually just run it out
> the window or drill a hole in the floor.  I guess that costs about
> one security deposit.  Landlords love me.  :/
>
> >From: "Mike Strock" <[email protected]>
> >Reply-To: SeattleWireless Talk List <[email protected]>
> >To: "'SeattleWireless Talk List'" <[email protected]>
> >Subject: Wiring folks out there?
> >Date: Sun, 20 Mar 2005 22:14:37 -0800
> >
> >
> >I've got a *very* small network wiring project I'd like to see if I can
get
> >some feedback on.
> >
> >I need to wire CAT5 to four spots in my house (upstairs) to a switch in
my
> >basement.
> >
> > >From what I've read, I need to use shielded CAT5.  Is this correct?
> >
> >Yes, I currently use wireless, but for this application, I need wired.
> >
> >I'm looking for guidance on shielded versus unshielded, and costs
> >associated
> >with getting four drops done....(each in a different room, terminating to
> >one spot in my basement where there is a switch).
> >
> >Thanks.
> >
> >Mike Strock
> >[email protected]
> >http://www.myhomeoffice.org/ - New pictures of my kids here!
> >
> >
> >
> >
> >_______________________________________________
> >Talk mailing list
> >[email protected]
> >http://seattlewireless.net/mailman/listinfo/talk
>
> _______________________________________________
> Talk mailing list
> [email protected]
> http://seattlewireless.net/mailman/listinfo/talk

_______________________________________________
Talk mailing list
[email protected]
http://seattlewireless.net/mailman/listinfo/talk



_______________________________________________
Talk mailing list
[email protected]
http://seattlewireless.net/mailman/listinfo/talk