RPI4-4Gb Boot fails from SD card (both my build AND the official 14.3 build)
Karl Denninger <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.arm |
|---|---|
| Message-ID | <[email protected]> |
Ugh..... this used to work, but I DID update this unit to the most-recent to use it with Kodi for a while, and now I get this when attempting to boot a FreeBSD load (this card DOES BOOT on a Pi3, incidentally; I know its good generally.) Looks like something has changed in the driver for the SD card that blows it up although the EFI Loader is able to read it and start the kernel. U-Boot 2025.04 (Jul 01 2025 - 23:03:56 +0000) DRAM: 948 MiB (effective 3.9 GiB) RPI 4 Model B (0xc03112) Core: 212 devices, 17 uclasses, devicetree: board MMC: mmc@7e300000: 3, mmc@7e340000: 0 Loading Environment from FAT... ** Bad device specification mmc 1 ** In: serial,usbkbd Out: serial,vidconsole Err: serial,vidconsole Net: eth0: ethernet@7d580000 PCIe BRCM: link up, 5.0 Gbps x1 (SSC) starting USB... Bus xhci_pci: Register 5000420 NbrPorts 5 Starting the controller USB XHCI 1.00 scanning bus xhci_pci for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 Cannot persist EFI variables without system partition ** Booting bootflow '<NULL>' with efi_mgr Booting: mmc 0 console comconsole failed to initialize Consoles: EFI console serial port Reading loader env vars from /efi/freebsd/loader.env Setting currdev to disk0p1: FreeBSD/arm64 EFI loader, Revision 3.0 Command line arguments: loader.efi Image base: 0x39d4f000 EFI version: 2.110 EFI Firmware: Das U-Boot (rev 8229.1024) Console: efi,comconsole (0) Load Path: /\EFI\BOOT\BOOTAA64.EFI Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6d00000003000000)/SD(0)/SD(1)/HD(1,MBR,0x15ca56f1,0x3f,0x18fe7) BootCurrent: 0000 BootOrder: 0000[*] Setting currdev to configured rootdev disk0s2a Loading /boot/defaults/loader.conf Loading /boot/defaults/loader.conf Loading /boot/device.hints Loading /boot/loader.conf Loading /boot/loader.conf.local c\ | ______ ____ _____ _____ | ____| | _ \ / ____| __ \ | |___ _ __ ___ ___ | |_) | (___ | | | | | ___| '__/ _ \/ _ \| _ < \___ \| | | | | | | | | __/ __/| |_) |____) | |__| | | | | | | | || | | | |_| |_| \___|\___||____/|_____/|_____/ ``` ` s` `.....---.......--.``` -/ +---------- Welcome to FreeBSD -----------+ +o .--` /y:` +. | | yo`:. :o `+- | 1. Boot Multi user [Enter] | y/ -/` -o/ | 2. Boot Single user | .- ::/sy+:. | 3. Escape to loader prompt | / `-- / | 4. Reboot | `: :` | 5. Cons: Dual (Serial primary) | `: :` | | / / | Options: | .- -. | 6. Kernel: default/kernel (1 of 1) | -- -. | 7. Boot Options | `:` `:` | | .-- `--. | | .---.....----. | | +-----------------------------------------+ Autoboot in 4 seconds. [Space] to pause Loading kernel... /boot/kernel/kernel text=0x2a8 text=0x9f2d10 text=0x26c014 data=0x151738 data=0x0+0x2bc000 0x8+0x154d70+0x8+0x17ec71 Loading configured modules... can't find '/boot/entropy' /boot/kernel/gpiopps.ko text=0x127b text=0x9d4 data=0x478 0x8+0x918+0x8+0x5f4 can't find '/etc/hostid' Using DTB provided by EFI at 0x39ee4000. EFI framebuffer information: addr, size 0x3eac2000, 0x103000 dimensions 592 x 448 stride 592 masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000 ---<<BOOT>>--- WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance Copyright (c) 1992-2023 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 14.3-STABLE #0 stable/14-n271967-a6693b09e297-dirty: Mon Jul 21 17:35:11 EDT 2025 [email protected]:/work/OBJ/ARM64-14-NTP-STABLE/obj/usr/src.14-STABLE/arm64.aarch64/sys/GENERIC arm64 FreeBSD clang version 19.1.7 (https://github.com/llvm/llvm-project.git llvmorg-19.1.7-0-gcd708029e0b2) VT(efifb): resolution 592x448 module scmi already present! real memory = 4148158464 (3955 MB) avail memory = 4020654080 (3834 MB) Starting CPU 1 (1) Starting CPU 2 (2) Starting CPU 3 (3) FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs random: unblocking device. random: entropy device external interface kbd0 at kbdmux0 Deprecated code (to be removed in FreeBSD 15): MIDI sequencer: no longer needed or used ofwbus0: <Open Firmware Device Tree> simplebus0: <Flattened device tree simple bus> on ofwbus0 ofw_clkbus0: <OFW clocks bus> on ofwbus0 simplebus1: <Flattened device tree simple bus> on ofwbus0 simplebus2: <Flattened device tree simple bus> on ofwbus0 regfix0: <Fixed Regulator> on ofwbus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency regfix1: <Fixed Regulator> on ofwbus0 regfix2: <Fixed Regulator> on ofwbus0 regfix3: <Fixed Regulator> on ofwbus0 regfix4: <Fixed Regulator> on ofwbus0 simplebus3: <Flattened device tree simple bus> on ofwbus0 simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 gpiobus0: <OFW GPIO bus> on gpio0 gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 gpiobus1: <GPIO bus> on gpio1 regfix0: Cannot configure GPIO pin: 5 REGNODE_INIT failed: 6 regfix0: Cannot register regulator. clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency regfix2: Cannot set GPIO pin: 6 REGNODE_INIT failed: 6 regfix2: Cannot register regulator. mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency gpioregulator0: <GPIO controlled regulator> on ofwbus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq 31,32,33,34,35,36,37,38,39,40,41 on simplebus0 usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on simplebus0 gpioc0: <GPIO controller> on gpio0 uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 uart0: console (115200,n,8,1) spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 spibus0: <OFW SPI bus> on spi0 spibus0: <unknown card> at cs 0 mode 0 spibus0: <unknown card> at cs 1 mode 0 sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 mmc0: <MMC/SD bus> on sdhci_bcm0 iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 27 on simplebus0 bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on simplebus0 bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e104027 on simplebus0 gpioc1: <GPIO controller> on gpio1 fb0: <BCM2835 VT framebuffer driver> on simplebus0 fb0: keeping existing fb bpp of 32 fbd0 on fb0 WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD 15.0. VT: Replacing driver "efifb" with new "fb". fb0: 592x448(592x448@0,0) 32bpp fb0: fbswap: 1, pitch 2368, base 0x3eac2000, screen_size 1060864 sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff irq 79 on simplebus1 mmc1: <MMC/SD bus> on sdhci_bcm1 pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0 cpulist0: <Open Firmware CPU Group> on ofwbus0 cpu0: <Open Firmware CPU> on cpulist0 bcm2835_cpufreq0: <CPU Frequency Control> on cpu0 cpufreq0: <CPU frequency control> on cpu0 pcib0: <BCM2838-compatible PCI-express controller> mem 0x7d500000-0x7d50930f irq 80,81 on simplebus2 pcib0: hardware identifies as revision 0x304. pci0: <OFW PCI bus> on pcib0 pcib1: <PCI-PCI bridge> irq 91 at device 0.0 on pci0 pci1: <OFW PCI bus> on pcib1 bcm_xhci0: <VL805 USB 3.0 controller (on the Raspberry Pi 4b)> irq 92 at device 0.0 on pci1 bcm_xhci0: 32 bytes context size, 64-bit DMA usbus0 on bcm_xhci0 genet0: <RPi4 Gigabit Ethernet> mem 0x7d580000-0x7d58ffff irq 82,83 on simplebus2 genet0: GENET version 5.0 phy 0x0000 miibus0: <MII bus> on genet0 brgphy0: <BCM54213PE 1000BASE-T media interface> PHY 1 on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto genet0: Ethernet address: dc:a6:32:8c:9e:8a clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency gpioled0: <GPIO LEDs> on ofwbus0 armv8crypto0: CPU lacks AES instructions Timecounters tick every 1.000 msec usbus0: 5.0Gbps Super Speed USB v3.0 sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== ugen0.1: <(0x1106) XHCI root HUB> at usbus0 uhub0 on usbus0 uhub0: <(0x1106) XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== mmc0: No compatible cards found on bus iicbus0: <OFW I2C bus> on iichb0 iic0: <I2C generic I/O> on iicbus0 mmcsd0: 128GB <SDHC SR128 8.6 SN 4F22B206 MFG 01/2024 by 3 SD> at mmc1 50.0MHz/4bit/65535-block bcm2835_cpufreq0: ARM 600MHz, Core 200MHz, SDRAM 400MHz, Turbo OFF uhub0: 5 ports with 4 removable, self powered CPU 0: ARM Cortex-A72 r0p3 affinity: 0 Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG> Instruction Set Attributes 0 = <CRC32> Instruction Set Attributes 1 = <> Instruction Set Attributes 2 = <> Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32> Trying to mount root from ufs:/dev/mmcsd0s2a [ro]... Processor Features 1 = <> Processor Features 2 = <> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA> Memory Model Features 1 = <8bit VMID> Memory Model Features 2 = <32bit CCIDX,48bit VA> Memory Model Features 3 = <> Memory Model Features 4 = <> Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8> Debug Features 1 = <> Auxiliary Features 0 = <> Auxiliary Features 1 = <> AArch32 Instruction Set Attributes 5 = <CRC32,SEVL> AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD> AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ> CPU 1: ARM Cortex-A72 r0p3 affinity: 1 CPU 2: ARM Cortex-A72 r0p3 affinity: 2 CPU 3: ARM Cortex-A72 r0p3 affinity: 3 gic0: using for IPIs Release APs...done TCP_ratelimit: Is now initialized ugen0.2: <vendor 0x2109 USB2.0 Hub> at usbus0 uhub1 on uhub0 uhub1: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.10/4.21, addr 1> on usbus0 uhub1: 4 ports with 4 removable, self powered sdhci_bcm1-slot0: Controller timeout sdhci_bcm1-slot0: ============== REGISTER DUMP ============== sdhci_bcm1-slot0: Sys addr: 0x000000c8 | Version: 0x00001002 sdhci_bcm1-slot0: Blk size: 0x00000200 | Blk cnt: 0x00000001 sdhci_bcm1-slot0: Argument: 0x0ee2afff | Trn mode: 0x00000012 sdhci_bcm1-slot0: Present: 0x1fff0a06 | Host ctl: 0x00000007 sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000080 sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x00000107 sdhci_bcm1-slot0: Timeout: 0x00000003 | Int stat: 0x00000000 sdhci_bcm1-slot0: Int enab: 0x01ff003b | Sig enab: 0x01ff0009 sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm1-slot0: Caps: 0x45ee6432 | Caps2: 0x0000a525 sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000 sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm1-slot0: =========================================== mmcsd0: Error indicated: 1 Timeout sdhci_bcm1-slot0: Controller timeout sdhci_bcm1-slot0: ============== REGISTER DUMP ============== sdhci_bcm1-slot0: Sys addr: 0x000000c8 | Version: 0x00001002 sdhci_bcm1-slot0: Blk size: 0x00000200 | Blk cnt: 0x00000001 sdhci_bcm1-slot0: Argument: 0x0ee2afff | Trn mode: 0x00000012 sdhci_bcm1-slot0: Present: 0x1fff0a06 | Host ctl: 0x00000007 sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000080 sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x00000107 sdhci_bcm1-slot0: Timeout: 0x00000003 | Int stat: 0x00000021 sdhci_bcm1-slot0: Int enab: 0x01ff003b | Sig enab: 0x01ff0008 sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm1-slot0: Caps: 0x45ee6432 | Caps2: 0x0000a525 sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000 sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm1-slot0: =========================================== mmcsd0: Error indicated: 1 Timeout sdhci_bcm1-slot0: Controller timeout sdhci_bcm1-slot0: ============== REGISTER DUMP ============== sdhci_bcm1-slot0: Sys addr: 0x000000c8 | Version: 0x00001002 sdhci_bcm1-slot0: Blk size: 0x00000200 | Blk cnt: 0x00000004 sdhci_bcm1-slot0: Argument: 0x0ee2afc1 | Trn mode: 0x00000036 sdhci_bcm1-slot0: Present: 0x1fff0a06 | Host ctl: 0x00000007 sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000080 sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x00000107 sdhci_bcm1-slot0: Timeout: 0x00000003 | Int stat: 0x00000021 sdhci_bcm1-slot0: Int enab: 0x01ff003b | Sig enab: 0x01ff0008 sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm1-slot0: Caps: 0x45ee6432 | Caps2: 0x0000a525 sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000 sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm1-slot0: =========================================== mmcsd0: Error indicated: 1 Timeout mmcsd0: Error indicated: 1 Timeout mmcsd0: Error indicated: 1 Timeout mmcsd0: Error indicated: 1 Timeout mmcsd0: Error indicated: 1 Timeout mountroot: waiting for device /dev/mmcsd0s2a... Mounting from ufs:/dev/mmcsd0s2a failed with error 19. Loader variables: vfs.root.mountfrom=ufs:/dev/mmcsd0s2a vfs.root.mountfrom.options=ro Manual root filesystem specification: <fstype>:<device> [options] Mount <device> using filesystem <fstype> and with the specified (optional) option list. eg. ufs:/dev/da0s1a zfs:zroot/ROOT/default cd9660:/dev/cd0 ro (which is equivalent to: mount -t cd9660 -o ro /dev/cd0 /) ? List valid disk boot devices . Yield 1 second (for background tasks) <empty line> Abort manual input mountroot> Tried writing the image on a newer (and much-faster) microSD card, no change. The OFFICIAL load for the RPI here also fails with the same error: https://download.freebsd.org/releases/ISO-IMAGES/14.3/ Any ideas on where to start looking as to what got borked as needless to say -- this sucks! -- Karl Denninger [email protected] /The Market Ticker/ /[S/MIME encrypted email preferred]/
smime.p7s
(application/pkcs7-signature, 4.3 KB) - not displayed