Re: RPI4-4Gb Boot fails from SD card (both my build AND the official 14.3 build)

BTW booting an "official" Pi distribution, updating it to be current off 
the 'net and then running rpi-eeprom-update says the bootloader and 
VL805 EEPROM are both up to date (8 May 2025 is what it says is on the 
board.)

On 7/26/2025 13:25, Karl Denninger wrote:
>
> Ugh..... this used to work, but I DID update this unit to the 
> most-recent to use it with Kodi for a while, and now I get this when 
> attempting to boot a FreeBSD load (this card DOES BOOT on a Pi3, 
> incidentally; I know its good generally.)  Looks like something has 
> changed in the driver for the SD card that blows it up although the 
> EFI Loader is able to read it and start the kernel.
>
> U-Boot 2025.04 (Jul 01 2025 - 23:03:56 +0000)
>
> DRAM:  948 MiB (effective 3.9 GiB)
> RPI 4 Model B (0xc03112)
> Core:  212 devices, 17 uclasses, devicetree: board
> MMC:   mmc@7e300000: 3, mmc@7e340000: 0
> Loading Environment from FAT... ** Bad device specification mmc 1 **
> In:    serial,usbkbd
> Out:   serial,vidconsole
> Err:   serial,vidconsole
> Net:   eth0: ethernet@7d580000
>
> PCIe BRCM: link up, 5.0 Gbps x1 (SSC)
> starting USB...
> Bus xhci_pci: Register 5000420 NbrPorts 5
> Starting the controller
> USB XHCI 1.00
> scanning bus xhci_pci for devices... 2 USB Device(s) found
>        scanning usb for storage devices... 0 Storage Device(s) found
> Hit any key to stop autoboot:  0
> Cannot persist EFI variables without system partition
> ** Booting bootflow '<NULL>' with efi_mgr
> Booting: mmc 0
> console comconsole failed to initialize
> Consoles: EFI console  serial port
>     Reading loader env vars from /efi/freebsd/loader.env
> Setting currdev to disk0p1:
> FreeBSD/arm64 EFI loader, Revision 3.0
>
>    Command line arguments: loader.efi
>    Image base: 0x39d4f000
>    EFI version: 2.110
>    EFI Firmware: Das U-Boot (rev 8229.1024)
>    Console: efi,comconsole (0)
>    Load Path: /\EFI\BOOT\BOOTAA64.EFI
>    Load Device: 
> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6d00000003000000)/SD(0)/SD(1)/HD(1,MBR,0x15ca56f1,0x3f,0x18fe7)
>    BootCurrent: 0000
>    BootOrder: 0000[*]
>     Setting currdev to configured rootdev disk0s2a
> Loading /boot/defaults/loader.conf
> Loading /boot/defaults/loader.conf
> Loading /boot/device.hints
> Loading /boot/loader.conf
> Loading /boot/loader.conf.local
> c\
> |  ______               ____   _____ _____
>   |  ____|             |  _ \ / ____|  __ \
>   | |___ _ __ ___  ___ | |_) | (___ | |  | |
>   |  ___| '__/ _ \/ _ \|  _ < \___ \| |  | |
>   | |   | | |  __/  __/| |_) |____) | |__| |
>   | |   | | |    |    ||     |      |      |
>   |_|   |_|  \___|\___||____/|_____/|_____/      ```             `
>                                                 s` 
> `.....---.......--.```   -/
>  +---------- Welcome to FreeBSD -----------+    +o   .--`  /y:`      +.
>  |                                         |     yo`:.   :o      `+-
>  |  1. Boot Multi user [Enter]             |      y/    -/`   -o/
>  |  2. Boot Single user                    |     .-     ::/sy+:.
>  |  3. Escape to loader prompt             |     /        `--  /
>  |  4. Reboot                              |    `:             :`
>  |  5. Cons: Dual (Serial primary)         |    `:             :`
>  |                                         |     /             /
>  |  Options:                               |     .-           -.
>  |  6. Kernel: default/kernel (1 of 1)     |      --           -.
>  |  7. Boot Options                        |       `:`         `:`
>  |                                         |         .--      `--.
>  |                                         | .---.....----.
>  |                                         |
>  +-----------------------------------------+
>    Autoboot in 4 seconds. [Space] to pause
> Loading kernel...
> /boot/kernel/kernel text=0x2a8 text=0x9f2d10 text=0x26c014 
> data=0x151738 data=0x0+0x2bc000 0x8+0x154d70+0x8+0x17ec71
> Loading configured modules...
> can't find '/boot/entropy'
> /boot/kernel/gpiopps.ko text=0x127b text=0x9d4 data=0x478 
> 0x8+0x918+0x8+0x5f4
> can't find '/etc/hostid'
> Using DTB provided by EFI at 0x39ee4000.
> EFI framebuffer information:
> addr, size     0x3eac2000, 0x103000
> dimensions     592 x 448
> stride         592
> masks          0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB 
> compliance
> Copyright (c) 1992-2023 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 14.3-STABLE #0 stable/14-n271967-a6693b09e297-dirty: Mon Jul 
> 21 17:35:11 EDT 2025
> [email protected]:/work/OBJ/ARM64-14-NTP-STABLE/obj/usr/src.14-STABLE/arm64.aarch64/sys/GENERIC 
> arm64
> FreeBSD clang version 19.1.7 (https://github.com/llvm/llvm-project.git 
> llvmorg-19.1.7-0-gcd708029e0b2)
> VT(efifb): resolution 592x448
> module scmi already present!
> real memory  = 4148158464 (3955 MB)
> avail memory = 4020654080 (3834 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> kbd0 at kbdmux0
> Deprecated code (to be removed in FreeBSD 15): MIDI sequencer: no 
> longer needed or used
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> regfix1: <Fixed Regulator> on ofwbus0
> regfix2: <Fixed Regulator> on ofwbus0
> regfix3: <Fixed Regulator> on ofwbus0
> regfix4: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 
> 0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> gic0: <ARM Generic Interrupt Controller> mem 
> 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff 
> irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 
> 14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot configure GPIO pin: 5
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> regfix2: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix2: Cannot register regulator.
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on 
> simplebus0
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq 
> 31,32,33,34,35,36,37,38,39,40,41 on simplebus0
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on 
> simplebus0
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on 
> simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 
> on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff 
> irq 24 on simplebus0
> mmc0: <MMC/SD bus> on sdhci_bcm0
> iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 27 
> on simplebus0
> bcmwd0: <BCM2708/2835 Watchdog> mem 
> 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on 
> simplebus0
> bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e104027 on 
> simplebus0
> gpioc1: <GPIO controller> on gpio1
> fb0: <BCM2835 VT framebuffer driver> on simplebus0
> fb0: keeping existing fb bpp of 32
> fbd0 on fb0
> WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD 
> 15.0.
> VT: Replacing driver "efifb" with new "fb".
> fb0: 592x448(592x448@0,0) 32bpp
> fb0: fbswap: 1, pitch 2368, base 0x3eac2000, screen_size 1060864
> sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff 
> irq 79 on simplebus1
> mmc1: <MMC/SD bus> on sdhci_bcm1
> pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0
> cpulist0: <Open Firmware CPU Group> on ofwbus0
> cpu0: <Open Firmware CPU> on cpulist0
> bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
> cpufreq0: <CPU frequency control> on cpu0
> pcib0: <BCM2838-compatible PCI-express controller> mem 
> 0x7d500000-0x7d50930f irq 80,81 on simplebus2
> pcib0: hardware identifies as revision 0x304.
> pci0: <OFW PCI bus> on pcib0
> pcib1: <PCI-PCI bridge> irq 91 at device 0.0 on pci0
> pci1: <OFW PCI bus> on pcib1
> bcm_xhci0: <VL805 USB 3.0 controller (on the Raspberry Pi 4b)> irq 92 
> at device 0.0 on pci1
> bcm_xhci0: 32 bytes context size, 64-bit DMA
> usbus0 on bcm_xhci0
> genet0: <RPi4 Gigabit Ethernet> mem 0x7d580000-0x7d58ffff irq 82,83 on 
> simplebus2
> genet0: GENET version 5.0 phy 0x0000
> miibus0: <MII bus> on genet0
> brgphy0: <BCM54213PE 1000BASE-T media interface> PHY 1 on miibus0
> brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
> 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
> genet0: Ethernet address: dc:a6:32:8c:9e:8a
> clk_fixed4: clock-fixed has no clock-frequency
> clk_fixed4: clock-fixed has no clock-frequency
> gpioled0: <GPIO LEDs> on ofwbus0
> armv8crypto0: CPU lacks AES instructions
> Timecounters tick every 1.000 msec
> usbus0: 5.0Gbps Super Speed USB v3.0
> sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no 
> active command.
> sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
> sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
> sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
> sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
> sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
> sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
> sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
> sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
> sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
> sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
> sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm0-slot0: ===========================================
> ugen0.1: <(0x1106) XHCI root HUB> at usbus0
> uhub0 on usbus0
> uhub0: <(0x1106) XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on 
> usbus0
> sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no 
> active command.
> sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
> sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
> sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
> sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
> sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
> sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
> sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
> sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
> sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
> sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
> sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm0-slot0: ===========================================
> sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no 
> active command.
> sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
> sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
> sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
> sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
> sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
> sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
> sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
> sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
> sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
> sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
> sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm0-slot0: ===========================================
> sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no 
> active command.
> sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
> sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
> sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
> sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
> sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
> sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
> sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
> sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
> sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
> sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
> sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm0-slot0: ===========================================
> sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no 
> active command.
> sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
> sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
> sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
> sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
> sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
> sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
> sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
> sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
> sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
> sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
> sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm0-slot0: ===========================================
> sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no 
> active command.
> sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
> sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
> sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
> sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
> sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
> sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
> sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
> sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
> sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
> sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
> sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm0-slot0: ===========================================
> sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no 
> active command.
> sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version:  0x00009902
> sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
> sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
> sdhci_bcm0-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
> sdhci_bcm0-slot0: Power:    0x0000000f | Blk gap:  0x00000000
> sdhci_bcm0-slot0: Wake-up:  0x00000000 | Clock:    0x00003947
> sdhci_bcm0-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
> sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
> sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm0-slot0: Caps:     0x00000000 | Caps2:    0x00000000
> sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
> sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm0-slot0: ===========================================
> mmc0: No compatible cards found on bus
> iicbus0: <OFW I2C bus> on iichb0
> iic0: <I2C generic I/O> on iicbus0
> mmcsd0: 128GB <SDHC SR128 8.6 SN 4F22B206 MFG 01/2024 by 3 SD> at mmc1 
> 50.0MHz/4bit/65535-block
> bcm2835_cpufreq0: ARM 600MHz, Core 200MHz, SDRAM 400MHz, Turbo OFF
> uhub0: 5 ports with 4 removable, self powered
> CPU  0: ARM Cortex-A72 r0p3 affinity:  0
>                    Cache Type = <64 byte D-cacheline,64 byte 
> I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG>
>  Instruction Set Attributes 0 = <CRC32>
>  Instruction Set Attributes 1 = <>
>  Instruction Set Attributes 2 = <>
>          Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
> Trying to mount root from ufs:/dev/mmcsd0s2a [ro]...
>          Processor Features 1 = <>
>          Processor Features 2 = <>
>       Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit 
> ASID,16TB PA>
>       Memory Model Features 1 = <8bit VMID>
>       Memory Model Features 2 = <32bit CCIDX,48bit VA>
>       Memory Model Features 3 = <>
>       Memory Model Features 4 = <>
>              Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 
> Watchpoints,6 Breakpoints,PMUv3,Debugv8>
>              Debug Features 1 = <>
>          Auxiliary Features 0 = <>
>          Auxiliary Features 1 = <>
> AArch32 Instruction Set Attributes 5 = <CRC32,SEVL>
> AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP 
> VFPv3+v4,SP VFPv3+v4,AdvSIMD>
> AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP 
> Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
> CPU  1: ARM Cortex-A72 r0p3 affinity:  1
> CPU  2: ARM Cortex-A72 r0p3 affinity:  2
> CPU  3: ARM Cortex-A72 r0p3 affinity:  3
> gic0: using for IPIs
> Release APs...done
>
> TCP_ratelimit: Is now initialized
> ugen0.2: <vendor 0x2109 USB2.0 Hub> at usbus0
> uhub1 on uhub0
> uhub1: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.10/4.21, addr 1> on 
> usbus0
> uhub1: 4 ports with 4 removable, self powered
> sdhci_bcm1-slot0: Controller timeout
> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm1-slot0: Sys addr: 0x000000c8 | Version:  0x00001002
> sdhci_bcm1-slot0: Blk size: 0x00000200 | Blk cnt:  0x00000001
> sdhci_bcm1-slot0: Argument: 0x0ee2afff | Trn mode: 0x00000012
> sdhci_bcm1-slot0: Present:  0x1fff0a06 | Host ctl: 0x00000007
> sdhci_bcm1-slot0: Power:    0x0000000f | Blk gap:  0x00000080
> sdhci_bcm1-slot0: Wake-up:  0x00000000 | Clock:    0x00000107
> sdhci_bcm1-slot0: Timeout:  0x00000003 | Int stat: 0x00000000
> sdhci_bcm1-slot0: Int enab: 0x01ff003b | Sig enab: 0x01ff0009
> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm1-slot0: Caps:     0x45ee6432 | Caps2:    0x0000a525
> sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000
> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm1-slot0: ===========================================
> mmcsd0: Error indicated: 1 Timeout
> sdhci_bcm1-slot0: Controller timeout
> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm1-slot0: Sys addr: 0x000000c8 | Version:  0x00001002
> sdhci_bcm1-slot0: Blk size: 0x00000200 | Blk cnt:  0x00000001
> sdhci_bcm1-slot0: Argument: 0x0ee2afff | Trn mode: 0x00000012
> sdhci_bcm1-slot0: Present:  0x1fff0a06 | Host ctl: 0x00000007
> sdhci_bcm1-slot0: Power:    0x0000000f | Blk gap:  0x00000080
> sdhci_bcm1-slot0: Wake-up:  0x00000000 | Clock:    0x00000107
> sdhci_bcm1-slot0: Timeout:  0x00000003 | Int stat: 0x00000021
> sdhci_bcm1-slot0: Int enab: 0x01ff003b | Sig enab: 0x01ff0008
> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm1-slot0: Caps:     0x45ee6432 | Caps2:    0x0000a525
> sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000
> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm1-slot0: ===========================================
> mmcsd0: Error indicated: 1 Timeout
> sdhci_bcm1-slot0: Controller timeout
> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
> sdhci_bcm1-slot0: Sys addr: 0x000000c8 | Version:  0x00001002
> sdhci_bcm1-slot0: Blk size: 0x00000200 | Blk cnt:  0x00000004
> sdhci_bcm1-slot0: Argument: 0x0ee2afc1 | Trn mode: 0x00000036
> sdhci_bcm1-slot0: Present:  0x1fff0a06 | Host ctl: 0x00000007
> sdhci_bcm1-slot0: Power:    0x0000000f | Blk gap:  0x00000080
> sdhci_bcm1-slot0: Wake-up:  0x00000000 | Clock:    0x00000107
> sdhci_bcm1-slot0: Timeout:  0x00000003 | Int stat: 0x00000021
> sdhci_bcm1-slot0: Int enab: 0x01ff003b | Sig enab: 0x01ff0008
> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
> sdhci_bcm1-slot0: Caps:     0x45ee6432 | Caps2:    0x0000a525
> sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000
> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
> sdhci_bcm1-slot0: ===========================================
> mmcsd0: Error indicated: 1 Timeout
> mmcsd0: Error indicated: 1 Timeout
> mmcsd0: Error indicated: 1 Timeout
> mmcsd0: Error indicated: 1 Timeout
> mmcsd0: Error indicated: 1 Timeout
> mountroot: waiting for device /dev/mmcsd0s2a...
> Mounting from ufs:/dev/mmcsd0s2a failed with error 19.
>
> Loader variables:
>   vfs.root.mountfrom=ufs:/dev/mmcsd0s2a
>   vfs.root.mountfrom.options=ro
>
> Manual root filesystem specification:
>   <fstype>:<device> [options]
>       Mount <device> using filesystem <fstype>
>       and with the specified (optional) option list.
>
>     eg. ufs:/dev/da0s1a
>         zfs:zroot/ROOT/default
>         cd9660:/dev/cd0 ro
>           (which is equivalent to: mount -t cd9660 -o ro /dev/cd0 /)
>
>   ?               List valid disk boot devices
>   .               Yield 1 second (for background tasks)
>   <empty line>    Abort manual input
>
> mountroot>
>
> Tried writing the image on a newer (and much-faster) microSD card, no 
> change.
>
> The OFFICIAL load for the RPI here also fails with the same error: 
> https://download.freebsd.org/releases/ISO-IMAGES/14.3/
>
> Any ideas on where to start looking as to what got borked as needless 
> to say -- this sucks!
>
> -- 
> Karl Denninger
> [email protected]
> /The Market Ticker/
> /[S/MIME encrypted email preferred]/
-- 
Karl Denninger
[email protected]
/The Market Ticker/
/[S/MIME encrypted email preferred]/