HAL status 3

Hi guys,

I'm using FreeBSD 6.0 stable and I'm trying to use a atheros card, but i 
got always the same msg.

ath0: <Atheros 5212> mem 0xa0010000-0xa001ffff irq 11 at device 14.0 on pci0
ath0: [GIANT-LOCKED]
ath0: unable to attach hardware; HAL status 3

I've search by google and found that puting this line in 
/boot/loader.conf, would work, but nothing.
hw.pci.allow_unsupported_io_range="1"

Someone already saw it?

Thanks

Luiz

==============dmesg============================
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 6.0-STABLE #2: Tue Jan 17 16:38:11 UTC 2006
    [email protected]:/usr/src/sys/i386/compile/SOEKRIS_6
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
WARNING: MPSAFE network stack disabled, expect reduced performance.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.62-MHz 
586-class CPU)
  Origin = "Geode by NSC"  Id = 0x540  Stepping = 0
  Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory  = 134217728 (128 MB)
avail memory = 126111744 (120 MB)
ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem 
0xa0000000-0xa0000fff irq 10 at device 6.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:00:24:c5:4c:64
sis0: [GIANT-LOCKED]
ath0: <Atheros 5212> mem 0xa0010000-0xa001ffff irq 11 at device 14.0 on pci0
ath0: [GIANT-LOCKED]
ath0: unable to attach hardware; HAL status 3
device_attach: ath0 attach returned 6
Geode GPIO@ = 6100
Geode Soekris net4801 comBIOS ver. 1.28 20050529 Copyright (C) 2000-2005
isab0: <PCI-ISA bridge> port 0x6100-0x613f,0x6200-0x623f at device 18.0 
on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 18.2 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
Geode CBA@ 0x6000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge> at device 18.5 (no driver attached)
pci0: <serial bus, USB> at device 19.0 (no driver attached)
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc8000-0xd0fff on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding 
enabled, default to accept, logging unlimited
ad0: 61MB <64MB ATA Flash Disk ADAA328E> at ata0-master WDMA2
Trying to mount root from ufs:/dev/ad0a

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"