Re: ath countrycode

Eric Anderson <[email protected]>
Newsgroups gmane.os.freebsd.devel.mobile
Message-ID <[email protected]>
Jiri Mikulas wrote:
> Hello
> I have ATH cards Wistron CM9 (AR5213),
> I want to set correct countrycode to use correct channels (ETSI)
> (channels 1-13 on 11g, channels 100-140 on 11a)
> but it's "disabled'
>
> osika:/# sysctl -a dev.ath.0.countrycode=203
> sysctl: oid 'dev.ath.0.countrycode' is read only
>
> On most HW wireles AP I can switch country (for example COMPEX WPE54AG-5GHz),
> on NetBSD and Linux I can set it too (according to this article http://www.fehu.org/atheros.html )
> so I'm little bit suprised, that it's 'forbiden' on Freebsd
>
> I have
>  FreeBSD 6.0-STABLE #1: Thu Jan 19 10:40:33 CET 2006
>  dev.ath.0.countrycode: 0
>  dev.ath.0.regdomain: 0
>  hw.ath.hal.version: 0.9.14.9
>  ath0: <Atheros 5212> mem 0xff920000-0xff92ffff irq 17 at device 2.0 on pci1
>  ath0: Ethernet address: 00:0b:6b:35:46:d7
>  ath0: mac 5.9 phy 4.3 radio 3.6
>
> osika:/# ifconfig ath0 list chan
> Channel   1 : 2412  Mhz 11g          Channel  48 : 5240  Mhz 11a
> Channel   2 : 2417  Mhz 11g          Channel  50 : 5250  Mhz 11a Turbo
> Channel   3 : 2422  Mhz 11g          Channel  52 : 5260  Mhz 11a
> Channel   4 : 2427  Mhz 11g          Channel  56 : 5280  Mhz 11a
> Channel   5 : 2432  Mhz 11g          Channel  58 : 5290  Mhz 11a Turbo
> Channel   6 : 2437  Mhz 11g          Channel  60 : 5300  Mhz 11a
> Channel   7 : 2442  Mhz 11g          Channel  64 : 5320  Mhz 11a
> Channel   8 : 2447  Mhz 11g          Channel 149 : 5745  Mhz 11a
> Channel   9 : 2452  Mhz 11g          Channel 152 : 5760  Mhz 11a Turbo
> Channel  10 : 2457  Mhz 11g          Channel 153 : 5765  Mhz 11a
> Channel  11 : 2462  Mhz 11g          Channel 157 : 5785  Mhz 11a
> Channel  36 : 5180  Mhz 11a          Channel 160 : 5800  Mhz 11a Turbo
> Channel  40 : 5200  Mhz 11a          Channel 161 : 5805  Mhz 11a
> Channel  42 : 5210  Mhz 11a Turbo    Channel 165 : 5825  Mhz 11a
> Channel  44 : 5220  Mhz 11a
>
>
> Is there any way to switch countrycode on FBSD please ?
>   

Did you try setting it in /boot/loader.conf?


Eric




-- 
------------------------------------------------------------------------
Eric Anderson        Sr. Systems Administrator        Centaur Technology
Anything that works is better than anything that doesn't.
------------------------------------------------------------------------

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.