Re: kernel: stray irq7
Yousef Raffah <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Organization | The Savola Group |
| Message-ID | <[email protected]> |
Ian Smith wrote:
> On Sat, 22 Jul 2006, Yousef Raffah wrote:
> > Ian Smith wrote:
> > > On Sat, 22 Jul 2006, Yousef Raffah wrote:
> > >
> > > > I have FreeBSD -CURRENT as of Mon Jul 17 20:06:47 AST 2006 on my
> > > > Toshiba Tecra A4 on my laptop and I keep on getting kernel: stray irq7
> > > > messages in my syslog and dmesg
> > > >
> > > > I have absolutely no idea what does it mean except that it is related to
> > > > irq(s) somehow!
> > >
> > > % dmesg | grep 'irq 7'
> > > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> > >
> > > Does your Tecra have a parallel port? Is it connected to anything?
>
> > Actually I do have a parallel port (DB25) that is not connected to
> > anything, but when I grep that, I get:
> > dmesg -a | grep ppc0
> > ppc0: parallel port not found
>
> Well that's not good news if you want it - maybe needs enabling in BIOS?
>
> It might pay to do a verbose-message boot and check dmesg carefully.
>
>
I have the verbose dmesg at the bottom.
> > stray irq7
> >
> > Does this help?
>
> Maybe related, but the irq 11 storm associated with cbb0 and iwi0 you
> reported to David W looks like more of a worry; I'll dip out of that.
>
> |> irq11: cbb0 iwi0+* 323649 13
>
> Cheers, Ian
>
>
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
rr232x: RocketRAID 232x controller driver v1.02 (Jul 17 2006 20:06:31)
npx0: INT 16 interface
acpi0: <INSYDE RSDT_000> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80010014
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25908086)
pcibios: BIOS version 2.10
Found $PIR table, 12 entries at 0xc00fe840
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 1 A 0x60 5 9 10 11
embedded 0 28 A 0x61 5 9 10 11
embedded 0 28 B 0x60 5 9 10 11
embedded 0 28 C 0x62 5 9 10 11
embedded 0 28 D 0x63 5 9 10 11
embedded 0 29 A 0x6b 5 9 10 11
embedded 0 29 B 0x63 5 9 10 11
embedded 0 29 C 0x62 5 9 10 11
embedded 0 29 D 0x60 5 9 10 11
embedded 0 30 A 0x61 5 9 10 11
embedded 0 30 B 0x68 5 9 10 11
embedded 0 31 A 0x62 5 9 10 11
embedded 0 31 B 0x63 5 9 10 11
embedded 0 31 D 0x60 5 9 10 11
embedded 1 0 A 0x60 5 9 10 11
embedded 1 0 B 0x61 5 9 10 11
embedded 1 0 C 0x62 5 9 10 11
embedded 1 0 D 0x63 5 9 10 11
embedded 2 0 A 0x60 5 9 10 11
embedded 2 0 B 0x61 5 9 10 11
embedded 2 0 C 0x62 5 9 10 11
embedded 2 0 D 0x63 5 9 10 11
embedded 3 0 A 0x61 5 9 10 11
embedded 3 0 B 0x62 5 9 10 11
embedded 3 0 C 0x63 5 9 10 11
embedded 3 0 D 0x60 5 9 10 11
embedded 4 0 A 0x62 5 9 10 11
embedded 4 0 B 0x63 5 9 10 11
embedded 4 0 C 0x60 5 9 10 11
embedded 4 0 D 0x61 5 9 10 11
embedded 5 0 A 0x63 5 9 10 11
embedded 5 0 B 0x60 5 9 10 11
embedded 5 0 C 0x61 5 9 10 11
embedded 5 0 D 0x62 5 9 10 11
embedded 6 4 A 0x60 5 9 10 11
embedded 6 4 B 0x61 5 9 10 11
embedded 6 6 A 0x62 5 9 10 11
embedded 6 6 B 0x63 5 9 10 11
embedded 6 6 C 0x6a 5 9 10 11
embedded 6 6 D 0x68 5 9 10 11
acpi_bus_number: root bus has no _BBN, assuming 0
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
AcpiOsDerivePciId: bus 6 dev 6 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xccb94000 pa 0x9d000
atpic: Programming IRQ9 as level/low
acpi_bus_number: root bus has no _BBN, assuming 0
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
AcpiOsDerivePciId: bus 0 dev 0 func 0
ACPI timer: 1/1 1/1 1/1 1/2 1/2 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x10> port 0x62,0x66 on acpi0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 5 11
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 5 11
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 11
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 5 10 11
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 10 N 0 5 10 11
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 10 11
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 5 11
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 5 11
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 11
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 5 10 11
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 5 10 11
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 10 11
pci_link4: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 5 11
pci_link4: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 5 N 0 5 11
pci_link4: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 11
pci_link5: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 10
pci_link5: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 10
pci_link5: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 10
pci_link6: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 6
pci_link6: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 6
pci_link6: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 6
pci_link7: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 5 10
pci_link7: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 10
pci_link7: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 10
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x1010
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.1.INTA at func 0: 11
ACPI: Found matching pin for 0.28.INTA at func 0: 10
ACPI: Found matching pin for 0.28.INTB at func 1: 11
ACPI: Found matching pin for 0.29.INTA at func 0: 11
pci_link7: BIOS IRQ 11 for 0.29.INTA is invalid
ACPI: Found matching pin for 0.29.INTB at func 1: 11
ACPI: Found matching pin for 0.29.INTC at func 2: 11
ACPI: Found matching pin for 0.29.INTD at func 3: 11
ACPI: Found matching pin for 0.30.INTA at func 2: 10
ACPI: Found matching pin for 0.30.INTB at func 3: 5
ACPI: Found matching pin for 0.31.INTB at func 2: 255
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x2590, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2591, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.LPCB.LNKA:0)
pcib0: slot 1 INTA routed to irq 11 via \\_SB_.PCI0.LPCB.LNKA
found-> vendor=0x8086, dev=0x2660, revid=0x04
bus=0, slot=28, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
pcib0: matched entry for 0.28.INTA (src \\_SB_.PCI0.LPCB.LNKB:0)
pcib0: slot 28 INTA routed to irq 10 via \\_SB_.PCI0.LPCB.LNKB
found-> vendor=0x8086, dev=0x2662, revid=0x04
bus=0, slot=28, func=1
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
pcib0: matched entry for 0.28.INTB (src \\_SB_.PCI0.LPCB.LNKA:0)
pcib0: slot 28 INTB routed to irq 11 via \\_SB_.PCI0.LPCB.LNKA
found-> vendor=0x8086, dev=0x2658, revid=0x04
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[20]: type 4, range 32, base 00001200, size 5, enabled
pcib0: matched entry for 0.29.INTA (src \\_SB_.PCI0.LPCB.LNKH:0)
pci_link7: Picked IRQ 5 with weight 0
pcib0: slot 29 INTA routed to irq 5 via \\_SB_.PCI0.LPCB.LNKH
found-> vendor=0x8086, dev=0x2659, revid=0x04
bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
map[20]: type 4, range 32, base 00001220, size 5, enabled
pcib0: matched entry for 0.29.INTB (src \\_SB_.PCI0.LPCB.LNKD:0)
pcib0: slot 29 INTB routed to irq 11 via \\_SB_.PCI0.LPCB.LNKD
found-> vendor=0x8086, dev=0x265a, revid=0x04
bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=11
map[20]: type 4, range 32, base 00001240, size 5, enabled
pcib0: matched entry for 0.29.INTC (src \\_SB_.PCI0.LPCB.LNKC:0)
pcib0: slot 29 INTC routed to irq 11 via \\_SB_.PCI0.LPCB.LNKC
found-> vendor=0x8086, dev=0x265b, revid=0x04
bus=0, slot=29, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
map[20]: type 4, range 32, base 00001260, size 5, enabled
pcib0: matched entry for 0.29.INTD (src \\_SB_.PCI0.LPCB.LNKA:0)
pcib0: slot 29 INTD routed to irq 11 via \\_SB_.PCI0.LPCB.LNKA
found-> vendor=0x8086, dev=0x265c, revid=0x04
bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base f4000000, size 10, memory disabled
pcib0: matched entry for 0.29.INTA (src \\_SB_.PCI0.LPCB.LNKH:0)
pcib0: slot 29 INTA routed to irq 5 via \\_SB_.PCI0.LPCB.LNKH
found-> vendor=0x8086, dev=0x2448, revid=0xd4
bus=0, slot=30, func=0
class=06-04-01, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x266e, revid=0x04
bus=0, slot=30, func=2
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000e000, size 8, enabled
map[14]: type 4, range 32, base 0000e100, size 6, enabled
map[18]: type 1, range 32, base d0000000, size 9, enabled
map[1c]: type 1, range 32, base d0000200, size 8, enabled
pcib0: matched entry for 0.30.INTA (src \\_SB_.PCI0.LPCB.LNKB:0)
pcib0: slot 30 INTA routed to irq 10 via \\_SB_.PCI0.LPCB.LNKB
found-> vendor=0x8086, dev=0x266d, revid=0x04
bus=0, slot=30, func=3
class=07-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=5
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000e200, size 8, enabled
map[14]: type 4, range 32, base 0000e300, size 7, enabled
pcib0: matched entry for 0.30.INTB (src \\_SB_.PCI0.LPCB.LNKE:0)
pcib0: slot 30 INTB routed to irq 5 via \\_SB_.PCI0.LPCB.LNKE
found-> vendor=0x8086, dev=0x2641, revid=0x04
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2653, revid=0x04
bus=0, slot=31, func=2
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 00001100, size 4, enabled
pcib1: <ACPI PCI-PCI bridge> irq 11 at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xc000-0xdfff
pcib1: memory decode 0xc0000000-0xcfffffff
pcib1: prefetched decode 0x90000000-0x9fffffff
ACPI: Found matching pin for 1.0.INTA at func 0: 11
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1002, dev=0x5460, revid=0x00
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 3, range 32, base 90000000, size 27, enabled
pcib1: (null) requested memory range 0x90000000-0x97ffffff: good
map[14]: type 4, range 32, base 0000c000, size 8, enabled
pcib1: (null) requested I/O range 0xc000-0xc0ff: in range
map[18]: type 1, range 32, base c0000000, size 16, enabled
pcib1: (null) requested memory range 0xc0000000-0xc000ffff: good
pcib1: matched entry for 1.0.INTA (src \\_SB_.PCI0.LPCB.LNKA:0)
pcib1: slot 0 INTA routed to irq 11 via \\_SB_.PCI0.LPCB.LNKA
vgapci0: <VGA-compatible display> port 0xc000-0xc0ff mem
0x90000000-0x97ffffff,0xc0000000-0xc000ffff irq 11 at device 0.0 on pci1
pcib2: <ACPI PCI-PCI bridge> irq 10 at device 28.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xa000-0xbfff
pcib2: memory decode 0xbc000000-0xbfffffff
pcib2: prefetched decode 0x8c000000-0x8fffffff
ACPI: Found matching pin for 2.0.INTA at func 0: 11
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
found-> vendor=0x11ab, dev=0x4362, revid=0x15
bus=2, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=4 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
MSI supports 2 messages, 64 bit
map[10]: type 1, range 64, base bc000000, size 14, enabled
pcib2: (null) requested memory range 0xbc000000-0xbc003fff: good
map[18]: type 4, range 32, base 0000a000, size 8, enabled
pcib2: (null) requested I/O range 0xa000-0xa0ff: in range
pcib2: matched entry for 2.0.INTA (src \\_SB_.PCI0.LPCB.LNKA:0)
pcib2: slot 0 INTA routed to irq 11 via \\_SB_.PCI0.LPCB.LNKA
pci2: <network, ethernet> at device 0.0 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> irq 11 at device 28.1 on pci0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0x8000-0x9fff
pcib3: memory decode 0xb8000000-0xbbffffff
pcib3: prefetched decode 0x88000000-0x8bffffff
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port
0x1200-0x121f irq 5 at device 29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1200
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port
0x1220-0x123f irq 11 at device 29.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1220
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port
0x1240-0x125f irq 11 at device 29.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1240
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port
0x1260-0x127f irq 11 at device 29.3 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1260
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801FB (ICH6) USB 2.0 controller> mem
0xf4000000-0xf40003ff irq 5 at device 29.7 on pci0
ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xf4000000
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801FB (ICH6) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4
uhub4: 8 ports with 8 removable, self powered
pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib4: secondary bus 6
pcib4: subordinate bus 6
pcib4: I/O decode 0x6000-0x7fff
pcib4: memory decode 0xb0000000-0xb7ffffff
pcib4: prefetched decode 0x80000000-0x87ffffff
pcib4: Subtractively decoded bridge.
ACPI: Found matching pin for 6.4.INTA at func 0: 11
ACPI: Found matching pin for 6.6.INTA at func 0: 255
ACPI: Found matching pin for 6.6.INTA at func 4: 11
ACPI: Found matching pin for 6.6.INTC at func 2: 11
pci_link6: BIOS IRQ 11 for 6.6.INTC is invalid
ACPI: Found matching pin for 6.6.INTD at func 3: 5
pci6: <ACPI PCI bus> on pcib4
pci6: physical bus=6
found-> vendor=0x8086, dev=0x4220, revid=0x05
bus=6, slot=4, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base b000b000, size 12, enabled
pcib4: (null) requested memory range 0xb000b000-0xb000bfff: good
pcib4: matched entry for 6.4.INTA (src \\_SB_.PCI0.LPCB.LNKA:0)
pcib4: slot 4 INTA routed to irq 11 via \\_SB_.PCI0.LPCB.LNKA
found-> vendor=0x104c, dev=0x8031, revid=0x00
bus=6, slot=6, func=0
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xc0 (48000 ns), maxlat=0x03
(750 ns)
intpin=a, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base 13000000, size 12, enabled
pcib4: (null) requested memory range 0x13000000-0x13000fff: good
found-> vendor=0x104c, dev=0x8032, revid=0x00
bus=6, slot=6, func=2
class=0c-00-10, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0210, cachelnsz=4 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
intpin=c, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base b0000000, size 11, enabled
pcib4: (null) requested memory range 0xb0000000-0xb00007ff: good
map[14]: type 1, range 32, base b0004000, size 14, enabled
pcib4: (null) requested memory range 0xb0004000-0xb0007fff: good
pcib4: matched entry for 6.6.INTC (src \\_SB_.PCI0.LPCB.LNKG:0)
pci_link6: Picked IRQ 9 with weight 0
pcib4: slot 6 INTC routed to irq 9 via \\_SB_.PCI0.LPCB.LNKG
found-> vendor=0x104c, dev=0x8033, revid=0x00
bus=6, slot=6, func=3
class=01-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0210, cachelnsz=4 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x07 (1750 ns), maxlat=0x04
(1000 ns)
intpin=d, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base b0008000, size 13, enabled
pcib4: (null) requested memory range 0xb0008000-0xb0009fff: good
pcib4: matched entry for 6.6.INTD (src \\_SB_.PCI0.LPCB.LNKE:0)
pcib4: slot 6 INTD routed to irq 5 via \\_SB_.PCI0.LPCB.LNKE
found-> vendor=0x104c, dev=0x8034, revid=0x00
bus=6, slot=6, func=4
class=08-05-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0210, cachelnsz=4 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x07 (1750 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base b000a000, size 8, enabled
pcib4: (null) requested memory range 0xb000a000-0xb000a0ff: good
map[14]: type 1, range 32, base b000a100, size 8, enabled
pcib4: (null) requested memory range 0xb000a100-0xb000a1ff: good
map[18]: type 1, range 32, base b000a200, size 8, enabled
pcib4: (null) requested memory range 0xb000a200-0xb000a2ff: good
pcib4: matched entry for 6.6.INTA (src \\_SB_.PCI0.LPCB.LNKC:0)
pcib4: slot 6 INTA routed to irq 11 via \\_SB_.PCI0.LPCB.LNKC
iwi0: <Intel(R) PRO/Wireless 2200BG> mem 0xb000b000-0xb000bfff irq 11 at
device 4.0 on pci6
iwi0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xb000b000
iwi0: bpf attached
iwi0: Ethernet address: 00:12:f0:63:ae:ca
iwi0: bpf attached
iwi0: bpf attached
iwi0: [MPSAFE]
iwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
iwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
24Mbps 36Mbps 48Mbps 54Mbps
cbb0: <TI6411 PCI-CardBus Bridge> mem 0x13000000-0x13000fff at device
6.0 on pci6
cbb0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0x13000000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib4: matched entry for 6.6.INTA (src \\_SB_.PCI0.LPCB.LNKC:0)
pcib4: slot 6 INTA routed to irq 11 via \\_SB_.PCI0.LPCB.LNKC
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
0x00: 0x8031104c 0x02100007 0x06070000 0x00824000
0x10: 0x13000000 0x020000a0 0x40080706 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b
0x40: 0xff101179 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x08409060 0x00000000 0x000f0002 0x01aa1b22
0x90: 0x606600c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe120001 0x00c00000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
fwohci0: vendor=104c, dev=8032
fwohci0: vendor=104c, dev=8032
fwohci0: <1394 Open Host Controller Interface> mem
0xb0000000-0xb00007ff,0xb0004000-0xb0007fff irq 9 at device 6.2 on pci6
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xb0000000
fwohci0: [MPSAFE]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:08:0d:a0:d1:bf:aa:e1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:08:0d:bf:aa:e1
fwe0: bpf attached
fwe0: Ethernet address: 02:08:0d:bf:aa:e1
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci6: <mass storage> at device 6.3 (no driver attached)
pci6: <base peripheral> at device 6.4 (no driver attached)
pcm0: <Intel ICH6 (82801FB)> port 0xe000-0xe0ff,0xe100-0xe13f mem
0xd0000000-0xd00001ff,0xd0000200-0xd00002ff irq 10 at device 30.2 on pci0
pcm0: Reserved 0x200 bytes for rid 0x18 type 3 at 0xd0000000
pcm0: Reserved 0x100 bytes for rid 0x1c type 3 at 0xd0000200
pcm0: [MPSAFE]
pcm0: <Analog Devices AD1981B AC97 Codec (id = 0x41445374)>
pcm0: Codec features headphone, 20 bit DAC, 5 bit master volume, no 3D
Stereo Enhancement
pcm0: Primary codec extended features variable rate PCM, AMAP, reserved 4
pcm0: ac97 codec dac ready count: 0
pcm0: sndbuf_setmap 1f452000, 4000; 0xd4ac8000 -> 1f452000
pcm0: sndbuf_setmap 1f44e000, 4000; 0xd4acc000 -> 1f44e000
pci0: <simple comms, generic modem> at device 30.3 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6 SATA150 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1100-0x110f at device 31.2 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1100
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=80 ostat1=80
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
acpi_tz2: <Thermal Zone> on acpi0
acpi_tz3: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0067
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
sio0: irq maps: 0xa21 0xa31 0xa21 0xa21
sio0: irq maps: 0xa21 0xa31 0xa21 0xa21
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
sio0: [FAST]
sio1: irq maps: 0xa21 0xa29 0xa21 0xa21
sio1: irq maps: 0xa21 0xa29 0xa21 0xa21
sio1 port 0x2f8-0x2ff,0x110-0x117 irq 3 drq 1 on acpi0
sio1: type 16550A
sio1: [FAST]
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
ex_isa_identify()
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
pass0 at ata1 bus 0 target 0 lun 0
pass0: <MATSHITA DVD-RAM UJ-831S 1.40> Removable CD-ROM SCSI-0 device
pass0: 33.000MB/s transfers
GEOM: new disk cd0
ATA PseudoRAID loaded
cd0 at ata1 bus 0 target 0 lun 0
cd0: <MATSHITA DVD-RAM UJ-831S 1.40> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: cd present [1 x 2048 byte records]
(cd0:ata1:0:0:0): error 22
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 22
(cd0:ata1:0:0:0): Unretryable Error
Trying to mount root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
battery0: battery initialization done, tried 2 times
Linux ELF exec handler installed
--
Sincerely,
Yousef Adnan Raffah
The Savola Group
-------------------
Aren't you using Firefox? Get it at http://www.getfirefox.com
signature.asc
(application/pgp-signature, 187 B)
-----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.4 (FreeBSD) iD8DBQFEwx8HqG4sHeIU6qURAnK6AKC1qU/kCrKzfHuZ9bV7W6byfnjHPACeOb/v ERAiumTiRUj1kpkqMmkLcQ0= =Ufv4 -----END PGP SIGNATURE-----