Re: ACPI Attach (acpi_ibm) stops mouse from working

> Date: Thu, 25 Oct 2007 09:20:49 +0100
> From: Tom Judge <[email protected]>
> 
> Kevin Oberman wrote:
> >> Date: Mon, 22 Oct 2007 17:04:52 +0100
> >> From: Tom Judge <[email protected]>
> >> Sender: [email protected]
> >>
> >> Hi,
> >>
> >>
> >> I have recently setup an IBM/Lenovo T43 with RELENG_7 as of mid last 
> >> week, however I have a problem with the acpi_ibm module.
> >>
> >> If I add acpi_ibm_load="YES" to loader.conf I get the following message 
> >> during boot:
> >>
> >> psm0: unable to allocate IRQ
> >>
> >> This is followed by a message stating that the acpi_ibm module has 
> >> attached to IRQ 12.
> >>
> >> If I remove this module from loader.conf and boot the system the mouse 
> >> attaches and works as expected.  If I then kldload acpi_ibm the module 
> >> attaches to acpi0.
> >>
> >>
> >> Is there any way to make this work without loading the acpi module after 
> >> boot?
> > 
> > I have a T43 and see the same thing if I load drivers in
> > /boot/loader.conf. I have seen it with both umass and it's USB brethren,
> > and if_ath. If I build them into the kernel or load them after the
> > system boots, there is no problem. Otherwise, no IRQ for the mouse (and
> > no mouse).
> > 
> > But you don't have to explicitly load ACPI. It's "magic" and
> > automatically loads if you don't disable it in hints. If it loads that
> > way, I have never had problems with the mouse.
> > 
> > jhb had some ideas of what caused the problem, but I have never had
> > time to pursue it and it is pretty rare.
> > 
> > Try removing the load from /boot/loader.conf and see if it works and if
> > you still get ACPI.
> 
> If I remove acpi_ibm_load="YES" from loader.conf I do indeed still get 
> acpi.  But what I don't get are access to the IBM acpi extensions such 
> as being able to use the access button to launch applications.  It all 
> seems to be related to the order in which the modules are loaded. If 
> acpi_ibm is loaded last then all is well, if not then it attaches to irq 
> 12 clobbering the ps2 port for the mouse.

How odd. I can't see why acpi_ibm would effect IRQs in any way.

Are you running with APIC? I am not.

Here are the contents of my loader.conf file:
#Increase PCM buffer for smoother sound
hint.pcm.0.buffersize="16384"
kern.maxfiles="25000"
# Kick the mouse on resume
hint.psm.0.flags="0x2000"
# Disable TCC CPU throttling
#hint.p4tcc.0.disabled="1"
#hint.acpi_throttle.0.disabled="1"
# The DVD/CD does DMA just fine
hw.ata.atapi.dma="1"
# Allow better power management of devices
hw.pci.do_power_nodriver="2"
hw.psm.synaptics_support="1"
# Don't use cpufreq on this system!
#cpufreq_load="YES"
wlan_scan_sta_load="YES"
# VESA allows full res VTYs (132x50 with mode 322)
vesa_load="YES"
# Support full disk encryption
geom_eli_load="YES"
# Support IBM ACPI extensions
acpi_ibm_load="YES"
# Load the sound driver
snd_ich_load="YES"
acpi_video_load="YES"
# Support WEP on WiFi
wlan_wep_load="YES"
# Don't enable firewall at boot as it breaks IPv6 RDP/NDP 
#ipfw_load="YES"
linux_load="YES"

These entries are for a variety of things and some may not be appropriate
or may be built into the kernel. I am running the latest available BIOS.
-- 
R. Kevin Oberman, Network Engineer
Energy Sciences Network (ESnet)
Ernest O. Lawrence Berkeley National Laboratory (Berkeley Lab)
E-mail: [email protected]			Phone: +1 510 486-8634
Key fingerprint:059B 2DDF 031C 9BA3 14A4  EADA 927D EBB3 987B 3751

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (FreeBSD)
Comment: Exmh version 2.5 06/03/2002

iD8DBQFHINnMkn3rs5h7N1ERAj1eAKC0rhOJKBjEEQ3PP1p/8mpu+/Bi0gCgke+O
n2XvKo369REtMf9XhOKN5bI=
=xKh0
-----END PGP SIGNATURE-----