sony vaio srx51p
David Haworth <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
good evening folks
I've just got my hands on a sony vaio srx51p. I think it goes by the
names srx7 in japan and srx77 in the states. this is a picture of it on
the sony website anyways
http://www.vaio.sony-europe.com/eng/products/notebooks/models/srx51p/content.html
anyways, I'm getting it all setup with freebsd on it but I can't seem to
find the wireless card.
the machine is a little subnotebook with onboard ethernet (found, works)
and then wireless (orinoco) and bluetooth. but with wi compiled into the
kernel, nothing shows up.
I have a feeling that the system can't cope with stuff in the pcmcia
slot (and I think the wireless and bluetooth stuff is considered a
pcmcia card, even though it's onboard. whats the situation with cardbus?
my old vaio (an sr11k) claims to have a cardbus controller (Ricoh
RL5C475 PCI-CardBus Bridge), in fact, the same one as on this new vaio
(although the new one seems to have 2 controllers, the second being a
"TI PCI-1410 PCI-CardBus Bridge". I've plugged my dlink dwl-650 into the
new vaio (which works fine with the old one) and also a 3com card. I get
informed of the insertion of both cards, but nothing else happens. they
aren't recognised and no drivers appear to be loaded.
is there anything I can do to get pcmcia or wireless working for this
laptop wihtout going to current? I was hoping to try DP2 but it seems to
be nowhere in sight (and dp1 crashes on boot of the cd).
for anyone else with one of these lappies. I seem to have most of the
rest of it working fine. I booted a 4.6.2 cd in the firewire dvd drive.
of course that couldn't install off the cd but it did get to sysinstall
where I could do a network install. I did need to set these at the boot
menu (and later in loader.conf, I thought that sysinstall might have
done that for me already but it didn't, without it things act very
strangely, the screen stops updating during boot for example)
set hw.pcic.irq=0
set hw.pcic.intr_path=1
however, X supports the intel 815 graphics. the onboard ethernet is
fxp0, works fine. sound seems to work fine. got the jogdial working as a
mouse scroll wheel (although the little "back" button doesn't seem to do
anything, also it doesn't generate any data from /dev/jogdial). no
firewire or bluetooth obvious as I've got no drivers for them so the
firewire dvd/cdrw ain't likely to work in freebsd for a while, but all
in good time I imagine.
don't think apm works either. doesn't give me any readout's or turn off
the machine for me, but afaik it's all acpi. roll on freebsd 5. vaiobat
from usr/ports/graphics/picturebook does appear to report battery status
correctly though and the setbrightness tool works (well, I can only seem
to make it either full bright, or miniumal brightness <shrug>)
anyways, here's as much info as I can cram into a post :)
root@alice:~# pccardc dumpcis
Read return -1 bytes (expected 2)
pccardc: CIS code read: Cannot allocate memory
Read return -1 bytes (expected 10)
Configuration data for card in slot 1
2 slots found
root@alice:~# cat /boot/loader.conf
# -- sysinstall generated deltas -- #
userconfig_script_load="YES"
hw.pcic.irq=0
hw.pcic.intr_path=1
agp_load="YES"
root@alice:~# dmesg
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.7-PRERELEASE #0: Thu Sep 5 22:43:45 BST 2002
[email protected]:/usr/obj/usr/src/sys/ALICE
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (496.83-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 266862592 (260608K bytes)
avail memory = 255787008 (249792K bytes)
Preloaded elf kernel "kernel" at 0xc03c0000.
Preloaded elf module "agp.ko" at 0xc03c009c.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 9 entries at 0xc00fdf30
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem 0xf4000000-0xf407ffff,0xf8000000-0xfbffffff irq 9 at device 2.0 on pci0
pcib1: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x104c, dev=0x8023) at 0.0 irq 9
pcic0: <Ricoh RL5C475 PCI-CardBus Bridge> irq 0 at device 2.0 on pci1
pcic0: PCI Memory allocated: 0x88000000
pcic0: Polling mode
pccard0: <PC Card bus (classic)> on pcic0
pcic1: <TI PCI-1410 PCI-CardBus Bridge> mem 0x44001000-0x44001fff at device 5.0 on pci1
pcic1: Polling mode
pcic1: TI12XX PCI Config Reg: [pwr save][pci only]
pccard1: <PC Card bus (classic)> on pcic1
fxp0: <Intel Pro/100 Ethernet> port 0x3000-0x303f mem 0xf4104000-0xf4104fff irq 9 at device 8.0 on pci1
fxp0: Ethernet address 08:00:46:54:72:7e
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=244c)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0x1800-0x180f at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0x1820-0x183f irq 9 at device 31.2 on pci0
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ichsmb0: <Intel 82801BA (ICH2) SMBus controller> port 0x1810-0x181f irq 9 at device 31.3 on pci0
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus general purpose I/O> on smbus0
uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0x1840-0x185f irq 9 at device 31.4 on pci0
usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ugen0: Sony USB Memory Stick Slot, rev 1.10/1.09, addr 2
pcm0: <Intel 82801BA (ICH2)> port 0x1880-0x18bf,0x1c00-0x1cff irq 9 at device 31.5 on pci0
pci0: <unknown card> (vendor=0x8086, dev=0x2446) at 31.6 irq 9
orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xd8000-0xdbfff,0xdc000-0xdffff on isa0
spic0: device model type = 2
spic0: <Sony Programmable I/O Controller> at port 0x10a0-0x10a4 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
IP Filter: v3.4.29 initialized. Default = pass all, Logging = enabled
ad0: 28615MB <HITACHI_DK23DA-30> [58140/16/63] at ata0-master UDMA100
Mounting root from ufs:/dev/ad0s2a
pccard: card inserted, slot 1
(notice that last line, thats in the dmesg from boot, I didn't put anything in the pcmcia slot for that. btw, anyone know what the sio devices are? the machine doesn't have any obvious serial ports and afaik the machine has a soft modem. is one that?)
root@alice:~# pciconf -lv
chip0@pci0:0:0: class=0x060000 card=0x80f2104d chip=0x11308086 rev=0x11 hdr=0x00
vendor = 'Intel Corporation'
device = '82815/EM/EP/P 815/EM/EP/P (Solano) Host to I/O Hub Bridge'
class = bridge
subclass = HOST-PCI
agp0@pci0:2:0: class=0x030000 card=0x80f2104d chip=0x11328086 rev=0x11 hdr=0x00
vendor = 'Intel Corporation'
device = '82815/EM/EP/P 815/EM/EP/P (Solano) Interal GUI Accelerator'
class = display
subclass = VGA
pcib1@pci0:30:0: class=0x060400 card=0x00000000 chip=0x24488086 rev=0x03 hdr=0x01
vendor = 'Intel Corporation'
device = '82801BAM/CAM Hub Interface to PCI Bridge (Camino 2)'
class = bridge
subclass = PCI-PCI
isab0@pci0:31:0: class=0x060100 card=0x00000000 chip=0x244c8086 rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BAM (ICH2-M) LPC Interface Controller'
class = bridge
subclass = PCI-ISA
atapci0@pci0:31:1: class=0x010180 card=0x80f2104d chip=0x244a8086 rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BAM (ICH2-M) UltraATA/100 IDE Controller'
class = mass storage
subclass = ATA
uhci0@pci0:31:2: class=0x0c0300 card=0x80f2104d chip=0x24428086 rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) USB Universal Host Controller'
class = serial bus
subclass = USB
ichsmb0@pci0:31:3: class=0x0c0500 card=0x80f2104d chip=0x24438086 rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) SMBus Controller'
class = serial bus
subclass = SMBus
uhci1@pci0:31:4: class=0x0c0300 card=0x80f2104d chip=0x24448086 rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) USB Universal Host Controller'
class = serial bus
subclass = USB
pcm0@pci0:31:5: class=0x040100 card=0x80f2104d chip=0x24458086 rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) AC'97 Audio Controller'
class = multimedia
subclass = audio
none0@pci0:31:6: class=0x070300 card=0x80f2104d chip=0x24468086 rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) AC'97 Modem Controller'
class = simple comms
none1@pci1:0:0: class=0x0c0010 card=0x80f2104d chip=0x8023104c rev=0x00 hdr=0x00
vendor = 'Texas Instruments (TI)'
device = 'TSB43AB22/A IEEE1394a-2000 OHCI PHY/Link-Layer Ctrlr'
class = serial bus
subclass = FireWire
pcic0@pci1:2:0: class=0x060700 card=0x80f2104d chip=0x04751180 rev=0x80 hdr=0x02
vendor = 'Communication Automation Corporation'
device = 'RL5C475 CardBus controller'
class = bridge
subclass = PCI-CardBus
pcic1@pci1:5:0: class=0x060700 card=0xab0112a3 chip=0xac50104c rev=0x01 hdr=0x02
vendor = 'Texas Instruments (TI)'
device = 'PCI1410 PC card cardBus Controller'
class = bridge
subclass = PCI-CardBus
fxp0@pci1:8:0: class=0x020000 card=0x8111104d chip=0x24498086 rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/CAM (ICH2/3) LAN Controller'
class = network
subclass = ethernet
root@alice:~# cat /sys/i386/conf/ALICE
machine i386
cpu I686_CPU
ident ALICE
maxusers 0
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Improve performance on big directories
options MFS #Memory Filesystem
options NFS #Network Filesystem
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
device smbus # Bus support, required for smb below.
device ichsmb
device smb
device pcm
options IPFILTER #ipfilter support
options IPFILTER_LOG #ipfilter logging
options RANDOM_IP_ID
options USER_LDT
device isa
device pci
device spic0 at isa? irq 0 port 0x10a0
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
options ATA_STATIC_ID #Static device numbering
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus?
# PCCARD (PCMCIA) support
device card
device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
device wi
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
pseudo-device snp
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
#device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device uscanner # Scanners
device urio # Diamond Rio MP3 Player
# USB Ethernet, requires mii
device aue # ADMtek USB ethernet
device cue # CATC USB ethernet
device kue # Kawasaki LSI USB ethernet
hmm.. I can't think of any other info to attach offhand. if anyone can
help I'd appreciate it.
many thanks
dave
To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message