Re: Please Help ..Modem & Sound Info

in message <[email protected]>,
wrote sonam singh thusly...
>
>  I successfuly installed the FreeBSD4.5 on ... Dell Inspiron 4100
>  Laptop .but i am not able to configure the modem and sound card
>  .It has PCtel Modem & Crystal 4205 Sound card .

it would help if you tell us the what are the actual problems and/or
error messages w/ the modem or the sound card.  what/how were you
trying to configure that gave you grief?

i don't have any experience w/ the mentioned sound card.  modem,
however, from the dmesg looks like, should just work ...  unless
it's a software modem.  speaking of which, what do you have for "sio"
in your kernel.  for example, i have...

# Serial (COM) ports
# sio0/com1 -- 9-pin serial port on dell inspiron 5000e
# sio2/com3 is winmodem
device          sio0    at isa? port IO_COM1 flags 0x10 irq 4
#device         sio1    at isa? port IO_COM2 irq 3
device          sio2    at isa? disable port IO_COM3


...and, if possible, please do not wrap the computer generated
messages like dmesg output below.

  - parv


> here is output of dmesg. i also try same thing which u
>  mentioned . I recompile the kernle with
>  device pcm
>  device csa
...
> Copyright (c) 1992-2002 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989,
> 1991, 1992, 1993, 1994
> 	The Regents of the University of California. All
> rights reserved.
> FreeBSD 4.5-RELEASE #0: Sun Apr  7 10:49:54 IST 2002
>    
> [email protected]:/usr/src/sys/compile/SON_KER2_1
> Timecounter "i8254"  frequency 1193182 Hz
> CPU: Pentium III/Pentium III Xeon/Celeron (863.79-MHz
> 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x6b1  Stepping = 1
>  
> Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
> real memory  = 134094848 (130952K bytes)
> config> di sn0
> config> di lnc0
> config> di le0
> No such device: le0
> Invalid command or syntax.  Type `?' for help.
> config> di ie0
> config> di fe0
> config> di ed0
> config> di cs0
> config> q
> avail memory = 125517824 (122576K bytes)
> Preloaded elf kernel "kernel" at 0xc04e1000.
> Preloaded userconfig_script "/boot/kernel.conf" at
> 0xc04e109c.
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> Using $PIR table, 11 entries at 0xc00fbba0
> apm0: <APM BIOS> on motherboard
> apm: found APM BIOS v1.2, connected at v1.2
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> pcib1: <PCI to PCI bridge (vendor=8086 device=3576)>
> at device 1.0 on pci0
> pci1: <PCI bus> on pcib1
> pci1: <ATI model 4c59 graphics accelerator> at 0.0 irq
> 11
> uhci0: <UHCI (generic) USB controller> port
> 0xbf80-0xbf9f irq 11 at device 29.0 on pci0
> uhci0: (New UHCI DeviceId=0x24828086)
> usb0: <UHCI (generic) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: (0x24828086) UHCI root hub, class 9/0, rev
> 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> pcib2: <PCI to PCI bridge (vendor=8086 device=2448)>
> at device 30.0 on pci0
> pci2: <PCI bus> on pcib2
> pcic0: <TI PCI-1420 PCI-CardBus Bridge> irq 11 at
> device 1.0 on pci2
> pcic0: PCI Memory allocated: 0x44000000
> pcic0: TI12XX PCI Config Reg: [ring enable][speaker
> enable][CSC serial isa irq]
> pccard0: <PC Card bus (classic)> on pcic0
> pcic1: <TI PCI-1420 PCI-CardBus Bridge> irq 11 at
> device 1.1 on pci2
> pcic1: PCI Memory allocated: 0x44001000
> pcic1: TI12XX PCI Config Reg: [ring enable][speaker
> enable][CSC serial isa irq]
> pccard1: <PC Card bus (classic)> on pcic1
> isab0: <PCI to ISA bridge (vendor=8086 device=248c)>
> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH3 ATA100 controller> port
> 0xbfa0-0xbfaf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7
> irq 0 at device 31.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> pcm0: <Intel 82801CA (ICH3)> port
> 0xdc80-0xdcbf,0xd800-0xd8ff irq 11 at device 31.5 on
> pci0
> pci0: <unknown card> (vendor=0x8086, dev=0x2486) at
> 31.6 irq 11
> orm0: <Option ROMs> at iomem
> 0xc0000-0xcefff,0xcf000-0xcf7ff,0xcf800-0xcffff on
> isa0
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7
> irq 6 drq 2 on isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> atkbdc0: <Keyboard controller (i8042)> at port
> 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model Generic PS/2 mouse, device ID 0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
> 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1: configured irq 3 not in bitmap of probed irqs 0
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on
> isa0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in
> COMPATIBLE mode
> ppc0: FIFO with 16/16/8 bytes threshold
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> pccard: card inserted, slot 0
> pccard: card removed, slot 0
> pcic0: Card type 32-bit cardbus is unsupported
> ad0: 19077MB <IC25N020ATDA04-0> [38760/16/63] at
> ata0-master UDMA100
> acd0: CDROM <LG CD-ROM CRN-8245B> at ata1-master using
> PIO4
> Mounting root from ufs:/dev/ad0s2a

-- 
 

To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message