Re: cardbus problem

> In message: <[email protected]>
>             "kalin mintchev" <[email protected]> writes:
> : cardbus1: Expecting link target, got 0xff
> : cardbus1: <old> at device 0.0 (no driver attached)
> : cbb1: CardBus card activation failed
>
> This sounds like a resource conflict of some sort.  0xff typically means
that there's no real hardware there, which in turn is usually due to
some resource issue :-(.  W/o a more complete dmesg, it is hard to say
more.
>
> Warner
>

thanks.... i guess better later then never...
below is the dmesg. i might be wrong but there is a lot going on pci0.
cbb0 says cardbus0 failed. cbb0 is on pci0 (which in turn is on pcib0
which is on apci0 which is on the motherboard and has a fixed Power
Button?!?!) but so is xl0 (nic) with the same irq....


acpi0: <PTLTD    RSDT  > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 11 entries at 0xc00fdee0
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
acpi_tz0: <Thermal Zone> port 0x530-0x537 on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 2 INTA is routed to irq 11
pcib0: slot 2 INTB is routed to irq 11
pcib0: slot 3 INTA is routed to irq 11
pcib0: slot 3 INTA is routed to irq 11
pcib0: slot 5 INTA is routed to irq 11
pcib0: slot 7 INTD is routed to irq 11
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem
0xf8000000-0xfbffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib1: slot 0 INTA is routed to irq 11
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <TI1450 PCI-CardBus Bridge> mem 0x50000000-0x50000fff irq 11 at
device 2.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [MPSAFE]
cbb1: <TI1450 PCI-CardBus Bridge> mem 0x50100000-0x50100fff irq 11 at
device 2.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
cbb1: [MPSAFE]
xl0: <3Com 3c556B Fast Etherlink XL> port 0x1800-0x18ff mem
0xe8101000-0xe810107f,0xe8101400-0xe810147f irq 11 at device 3.0 on pci0
xl0: chip is in D3 power mode -- setting to D0
xl0: Ethernet address: 00:00:86:43:54:46
miibus0: <MII bus> on xl0
acphy0: <AC101 10/100 media interface> on miibus0
acphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <simple comms> at device 3.1 (no driver attached)
csa0: <CS4280/CS4614/CS4622/CS4624/CS4630> mem
0xe8000000-0xe80fffff,0xe8100000-0xe8100fff irq 11 at device 5.0 on pci0
csa: card is Thinkpad 600X/A20/T20
pcm0: <CS461x PCM Audio> on csa0
pcm0: <Cirrus Logic CS4297A AC97 Codec>
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0x1c00-0x1c0f at device 7.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1c20-0x1c3f irq 11
at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
ppc0 port 0x3bc-0x3c3 irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
acpi_ec0: <Embedded Controller: GPE 0x9, GLK> port 0x66,0x62 on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
orm0: <Option ROMs> at iomem
0xe0000-0xeffff,0xcc000-0xcc7ff,0xc0000-0xcbfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 746757463 Hz quality 800
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
cardbus0: Expecting link target, got 0xff
cardbus0: Resource not specified in CIS: id=10, size=10
cardbus0: <old> at device 0.0 (no driver attached)
cbb0: CardBus card activation failed



--



_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"