Re: FirePro M5100 Support in drm-next-kmod?

Jacob Meadows <[email protected]>
Newsgroups gmane.os.freebsd.devel.x11
Message-ID <[email protected]>
It is actually 

kld_list="/boot/modules/amdgpu.ko" as leaving out the .ko causes nothing to attempt to load.  
I still have the same system freeze with that line as with the kld_list="amdgpu"
--------------------------------------------
On Tue, 10/23/18, Doug Kirk <[email protected]> wrote:

 Subject: Re: FirePro M5100 Support in drm-next-kmod?
 To: "Jacob Meadows" <[email protected]>
 Cc: [email protected]
 Date: Tuesday, October 23, 2018, 3:49 PM
 
 From what
 I understand, you should probably try
  
 kld_list="/boot/modules/amdgpu"
 in rc.conf to ensure you're
 picking up the port kmod instead of the base
 kmod.
 On Tue, Oct 23,
 2018 at 2:45 PM Jacob Meadows <[email protected]>
 wrote:
 I am testing FreeBSD on a Dell
 Latitude M4800 with an AMD FirePro M5100 mxm video card. 
 On a clean install, I install drm-next-kmod from ports, then
 add kld_list="amdgpu" to the /etc/rc.conf.  On
 reboot, the system freezes during the driver loading, and I
 have to physically power off the system and boot into single
 user mode to disable the driver and recover.
 
 
 
 I have tried this in 11.2 and 12.0 Beta1.  I have tried
 drm-stable-kmod as well.  I have tried this in both UEFI
 and legacy boot modes, but it happens the same each time. 
 If I load the i915 driver, that loads without issue.
 
 
 
 I run "pciconf –lv | grep display –B 3 –A"
 and get the following result:
 
 
 
 Vgapci1@pci0:0:2:0:     Class=0x030000 card=0x05cc1028
 chip=0x04168086 rev=0x06 hdr=0x00
 
         Vendor  = ‘Intel Corporation’
 
         Device  = ‘4th Gen Core Processor Integrated
 Graphics Controller’
 
         Class   = display
 
         Subclass = VGA
 
 --
 
 Vgapci0@pci0:1:0:0:     class-0x030000 card=0x05cc1028
 chip=0x68211002 rev=0x00 hdr=0x00
 
         Vendor  = ‘Advanced Micro Devices, Inc.
 [AMD/ATI]’
 
         Device  = ‘Venus XT [Radeon HD 8870M / R9
 M270X/M370X]’
 
         Class   = display
 
         Subclass        = VGA
 
 
 
 
 
 I do see an error during boot, but otherwise seems to be
 ok:
 
 Radeon/verde_me.bin: could not load firmware image, error
 2
 
 Radeon/verde_me.bin: could not load firmware image, error
 2
 
 Radeon/verde_ce.bin: could not load firmware image, error
 2
 
 Radeon/verde_ce.bin: could not load firmware image, error
 2
 
 Radeon/verde_rlc.bin: could not load firmware image, error
 2
 
 Radeon/verde_rlc.bin: could not load firmware image, error
 2
 
 
 
 My question is this:  Is this particular card unsupported,
 or is there something I am missing?
 
 _______________________________________________
 
 [email protected]
 mailing list
 
 https://lists.freebsd.org/mailman/listinfo/freebsd-x11
 
 To unsubscribe, send any mail to "[email protected]"
 
 
_______________________________________________
[email protected] mailing list
https://lists.freebsd.org/mailman/listinfo/freebsd-x11
To unsubscribe, send any mail to "[email protected]"
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.