Re: 5.0 restorecd

Just wanted to say that the 5.0 restorecd works like a charm on a Cobalt
Qube 2700. Took me some time to get the Qube to netboot, because the
RestoreCD doesn't always set up the network cards in the bootserver
properly, so you have to dive into the command line and play about with
ifconfig.

Question: what is the default configuration for the GENERIC Cobalt
kernel? I want to try and get a USB or WiFi card to work in the older
PCI slot.

It detects the USB chips, but doesn't configure them, so I'm assuming
the kernel drivers are missing.

Anthony


NetBSD 5.0 (GENERIC) #0: Sun Apr 26 10:39:04 UTC 2009

[email protected]:/home/builds/ab/netbsd-5-0-RELEASE/cobalt/200904260229Z-obj/home/builds/ab/netbsd-5-0-RELEASE/src/sys/arch/cobalt/compile/GENERIC
Cobalt Qube 2700
total memory = 65536 KB
avail memory = 59504 KB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root)
cpu0 at mainbus0: QED RM5200 CPU (0x2810) Rev. 1.0 with built-in FPU
Rev. 1.0
cpu0: 16KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 16KB/32B 2-way set-associative write-back L1 Data cache
mcclock0 at mainbus0 addr 0x10000070: mc146818 compatible time-of-day clock
panel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64011 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21041 Ethernet, pass 2.1
tlp0: interrupting at level 2
tlp0: Ethernet address 00:10:e0:00:09:e0
tlp0: 10baseT, 10baseT-FDX, 10base2, 10base5
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 PCI-ISA Bridge, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
VIA Technologies VT83C572 USB Controller (USB serial bus, revision 0x02)
at pci0 dev 9 function 2 not configured
Opti 82C861 (USB serial bus, interface 0x10, revision 0x10) at pci0 dev
10 function 0 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mips3_cp0_counter" frequency 75000000 Hz
quality 100
wd0 at atabus0 drive 0: <SAMSUNG WU32163A (2.16GB)>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 2060 MB, 4186 cyl, 16 head, 63 sec, 512 bytes/sect x 4219488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs


-- 
Anthony C Howe            Skype: SirWumpus                  SnertSoft
+33 6 11 89 73 78       Twitter: SirWumpus      BarricadeMX & Milters
http://snert.com/      http://nanozen.info/     http://snertsoft.com/