Re: LSI MegaRAID installation

On Mon, 30 Apr 2018, Steve Blinkhorn wrote:
> I can't see anything in dmesg.boot: it's conceivable that if RAID mode
> is not configured in the BIOS then the chip won't show up I suppose.
> But in case you know different dmesg.boot is appended below.

You will still see the PCI device, e.g.:

vendor 1000 product 0016 (RAID mass storage, revision 0x01) at pci11 dev 0 function 0 not configured

It sounds as though you have undetected PCI busses (or devices on those 
busses). Perhaps you could use pcictl to list the devices (and perhaps 
compare to another OS)?

> I'll try to boot from a USB port with the machine configured in RAID
> mode.
>
>
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
>    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017
>    The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>    The Regents of the University of California.  All rights reserved.
>
> NetBSD 8.0_RC1 (GENERIC.201804201240Z)
> total memory = 8055 MB
> avail memory = 7799 MB
> cpu_rng: RDSEED
> timecounter: Timecounters tick every 10.000 msec
> Kernelized RAIDframe activated
> running cgd selftest aes-xts-256 aes-xts-512 done
> timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
> FUJITSU PRIMERGY RX1330 M3 (GS01)
> mainbus0 (root)
> ACPI: RSDP 0x00000000000F05B0 000024 (v02 FUJ   )
> ACPI: XSDT 0x0000000087AA10A8 0000CC (v01 FUJ    D3375-B1 11300000 AMI  00010013)
> ACPI: FACP 0x0000000087AC3CC8 00010C (v05 FUJ    D3375-B1 11300000 AMI  00010013)
> ACPI: DSDT 0x0000000087AA1200 022AC6 (v02 FUJ    D3375-B1 11300000 INTL 20120913)
> ACPI: FACS 0x000000008EB7CF80 000040
> ACPI: APIC 0x0000000087AC3DD8 000084 (v03 FUJ    D3375-B1 11300000 AMI  00010013)
> ACPI: FPDT 0x0000000087AC3E60 000044 (v01 FUJ    D3375-B1 11300000 AMI  00010013)
> ACPI: FIDT 0x0000000087AC3EA8 00009C (v01 FUJ    D3375-B1 11300000 AMI  00010013)
> ACPI: SPMI 0x0000000087AC3F48 000041 (v05 FUJ    D3375-B1 00000000 AMI. 00000000)
> ACPI: MCFG 0x0000000087AC3F90 00003C (v01 FUJ    D3375-B1 11300000 MSFT 00000097)
> ACPI: HPET 0x0000000087AC3FD0 000038 (v01 FUJ    D3375-B1 11300000 AMI. 0005000B)
> ACPI: LPIT 0x0000000087AC4008 000094 (v01 INTEL  GNLR     00000000 MSFT 0000005F)
> ACPI: SSDT 0x0000000087AC40A0 000248 (v02 INTEL  sensrhub 00000000 INTL 20120913)
> ACPI: SSDT 0x0000000087AC42E8 0006DE (v02 INTEL  USB_MAP  00000000 INTL 20120913)
> ACPI: DBGP 0x0000000087AC49C8 000034 (v01 INTEL           00000000 MSFT 0000005F)
> ACPI: DBG2 0x0000000087AC4A00 000054 (v00 INTEL           00000000 MSFT 0000005F)
> ACPI: PRAD 0x0000000087AC4A58 0000CA (v02 PRADID PRADTID  00000001 INTL 20120913)
> ACPI: SSDT 0x0000000087AC4B28 005277 (v02 SaSsdt SaSsdt   00003000 INTL 20120913)
> ACPI: UEFI 0x0000000087AC9DA0 000042 (v01                 00000000      00000000)
> ACPI: SSDT 0x0000000087AC9DE8 000E73 (v02 CpuRef CpuSsdt  00003000 INTL 20120913)
> ACPI: DMAR 0x0000000087ACAC60 000070 (v01 INTEL  SKL      00000001 INTL 00000001)
> ACPI: EINJ 0x0000000087ACACD0 000130 (v01 AMI    AMI.EINJ 00000000 AMI. 00000000)
> ACPI: ERST 0x0000000087ACAE00 000230 (v01 AMIER  AMI.ERST 00000000 AMI. 00000000)
> ACPI: BERT 0x0000000087ACB030 000030 (v01 AMI    AMI.BERT 00000000 AMI. 00000000)
> ACPI: HEST 0x0000000087ACB060 0000A8 (v01 AMI    AMI.HEST 00000000 AMI. 00000000)
> ACPI: Executed 20 blocks of module-level executable AML code
> ACPI: Executed 2 blocks of module-level executable AML code
> ACPI: 5 ACPI AML tables successfully acquired and loaded
> ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 120 pins
> cpu0 at mainbus0 apid 0
> cpu0: Intel(R) Xeon(R) CPU E3-1220 v6 @ 3.00GHz, id 0x906e9
> cpu0: package 0, core 0, smt 0
> cpu1 at mainbus0 apid 2
> cpu1: Intel(R) Xeon(R) CPU E3-1220 v6 @ 3.00GHz, id 0x906e9
> cpu1: package 0, core 1, smt 0
> cpu2 at mainbus0 apid 4
> cpu2: Intel(R) Xeon(R) CPU E3-1220 v6 @ 3.00GHz, id 0x906e9
> cpu2: package 0, core 2, smt 0
> cpu3 at mainbus0 apid 6
> cpu3: Intel(R) Xeon(R) CPU E3-1220 v6 @ 3.00GHz, id 0x906e9
> cpu3: package 0, core 3, smt 0
> acpi0 at mainbus0: Intel ACPICA 20170303
> acpi0: X/RSDT: OemId <FUJ   ,D3375-B1,11300000>, AslId <AMI ,00010013>
> acpi0: MCFG: segment 0, bus 0-255, address 0x00000000e0000000
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFE826DCEA808 00037F (v02 PmRef  Cpu0Cst  00003001 INTL 20120913)
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFE826DDB3008 000660 (v02 PmRef  Cpu0Ist  00003000 INTL 20120913)
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFE826DDB1008 0005AA (v02 PmRef  ApIst    00003000 INTL 20120913)
> ACPI: Dynamic OEM Table Load:
> ACPI: SSDT 0xFFFFFE810E579308 000119 (v02 PmRef  ApCst    00003000 INTL 20120913)
> acpi0: SCI interrupting at int 9
> timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
> hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
> timecounter: Timecounter "hpet0" frequency 24000000 Hz quality 2000
> acpiec0 at acpi0 (H_EC, PNP0C09-1)acpiec0: unable to evaluate _GPE: AE_NOT_FOUND
> pckbc1 at acpi0 (PS2K, MSFT0001) (kbd port): io 0x60,0x64 irq 1
> pckbc2 at acpi0 (PS2M, MSFT0003) (aux port): irq 12
> SIO1 (PNP0C02) at acpi0 not configured
> UAR1 (PNP0501) at acpi0 not configured
> FWHD (INT0800) at acpi0 not configured
> LDRC (PNP0C02) at acpi0 not configured
> LDR2 (PNP0C02) at acpi0 not configured
> attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
> CWDT (INT3F0D) at acpi0 not configured
> SPMI (IPI0001) at acpi0 not configured
> PDRC (PNP0C02) at acpi0 not configured
> IOTR (PNP0C02) at acpi0 not configured
> GPI0 (INT345D) at acpi0 not configured
> PEPD (INT33A1) at acpi0 not configured
> acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
> PMT1 (ACPI000D) at acpi0 not configured
> FJGI (FUJ0420) at acpi0 not configured
> ACPI: Enabled 5 GPEs in block 00 to 7F
> pckbc: cmd word write error
> ipmi0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1
> pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
> pchb0 at pci0 dev 0 function 0: vendor 8086 product 5918 (rev. 0x05)
> xhci0 at pci0 dev 20 function 0: vendor 8086 product a12f (rev. 0x31)
> xhci0: interrupting at msi0 vec 0
> xhci0: xHCI version 1.0
> usb0 at xhci0: USB revision 3.0
> usb1 at xhci0: USB revision 2.0
> vendor 8086 product a131 (miscellaneous DASP, revision 0x31) at pci0 dev 20 function 2 not configured
> vendor 8086 product a13a (miscellaneous communications, revision 0x31) at pci0 dev 22 function 0 not configured
> vendor 8086 product a13b (miscellaneous communications, revision 0x31) at pci0 dev 22 function 1 not configured
> ahcisata0 at pci0 dev 23 function 0: vendor 8086 product a102 (rev. 0x31)
> ahcisata0: interrupting at ioapic0 pin 16
> ahcisata0: 64-bit DMA
> ahcisata0: AHCI revision 1.31, 8 ports, 32 slots, CAP 0xe334ff47<EMS,PSC,SSC,PMD,SAM,ISS=0x3=Gen3,SCLO,SAL,SSNTF,SNCQ,S64A>
> atabus0 at ahcisata0 channel 0
> atabus1 at ahcisata0 channel 1
> atabus2 at ahcisata0 channel 2
> atabus3 at ahcisata0 channel 3
> atabus4 at ahcisata0 channel 4
> atabus5 at ahcisata0 channel 5
> ppb0 at pci0 dev 28 function 0: vendor 8086 product a114 (rev. 0xf1)
> ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 8.0GT/s
> ppb0: link is x1 @ 2.5GT/s
> pci1 at ppb0 bus 1
> pci1: i/o space, memory space enabled
> vga0 at pci1 dev 0 function 0: vendor 102b product 0522 (rev. 0x05)
> wsdisplay0 at vga0 kbdmux 1
> wsmux1: connecting to wsdisplay0
> drm at vga0 not configured
> vendor 19a2 product 0800 (Co-processor processor) at pci1 dev 0 function 1 not configured
> ppb1 at pci0 dev 28 function 5: vendor 8086 product a115 (rev. 0xf1)
> ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 8.0GT/s
> ppb1: link is x1 @ 2.5GT/s
> pci2 at ppb1 bus 3
> pci2: i/o space, memory space enabled
> wm0 at pci2 dev 0 function 0: I210-T1 Ethernet Server Adapter (rev. 0x03)
> wm0: for TX and RX interrupting at msix1 vec 0 affinity to 0
> wm0: for TX and RX interrupting at msix1 vec 1 affinity to 1
> wm0: for TX and RX interrupting at msix1 vec 2 affinity to 2
> wm0: for TX and RX interrupting at msix1 vec 3 affinity to 3
> wm0: for LINK interrupting at msix1 vec 4
> wm0: PCI-Express bus
> wm0: 2048 words FLASH(HW), version 3.25, Image Unique ID 00000603
> wm0: Ethernet address 90:1b:0e:e8:82:09
> wm0: Copper
> wm0: 0x8214500<FLASH_HW,IOH_VALID,PCIE,NEWQUEUE,WOL>
> ukphy0 at wm0 phy 1: OUI 0x000ac2, model 0x0000, rev. 0
> ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
> ppb2 at pci0 dev 28 function 6: vendor 8086 product a116 (rev. 0xf1)
> ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 8.0GT/s
> ppb2: link is x1 @ 2.5GT/s
> pci3 at ppb2 bus 2
> pci3: i/o space, memory space enabled
> wm1 at pci3 dev 0 function 0: I210-T1 Ethernet Server Adapter (rev. 0x03)
> wm1: for TX and RX interrupting at msix2 vec 0 affinity to 0
> wm1: for TX and RX interrupting at msix2 vec 1 affinity to 1
> wm1: for TX and RX interrupting at msix2 vec 2 affinity to 2
> wm1: for TX and RX interrupting at msix2 vec 3 affinity to 3
> wm1: for LINK interrupting at msix2 vec 4
> wm1: PCI-Express bus
> wm1: 2048 words FLASH(HW), version 3.25, Image Unique ID 00000604
> wm1: Ethernet address 90:1b:0e:e8:61:87
> wm1: Copper
> wm1: 0x8214500<FLASH_HW,IOH_VALID,PCIE,NEWQUEUE,WOL>
> ukphy1 at wm1 phy 1: OUI 0x000ac2, model 0x0000, rev. 0
> ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
> pcib0 at pci0 dev 31 function 0: vendor 8086 product a149 (rev. 0x31)
> vendor 8086 product a121 (miscellaneous memory, revision 0x31) at pci0 dev 31 function 2 not configured
> ichsmb0 at pci0 dev 31 function 4: vendor 8086 product a123 (rev. 0x31)
> ichsmb0: interrupting at ioapic0 pin 16
> iic0 at ichsmb0: I2C bus
> isa0 at pcib0
> com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
> com0: console
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0: PC Speaker
> midi0 at pcppi0: PC speaker
> sysbeep0 at pcppi0
> attimer1: attached to pcppi0
> acpicpu0 at cpu0: ACPI CPU
> acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
> acpicpu0: C2: FFH, lat 151 us, pow   200 mW
> acpicpu0: C3: FFH, lat 256 us, pow   200 mW
> acpicpu0: P0: FFH, lat  10 us, pow 72000 mW, 3001 MHz, turbo boost
> acpicpu0: P1: FFH, lat  10 us, pow 72000 mW, 3000 MHz
> acpicpu0: P2: FFH, lat  10 us, pow 65442 mW, 2800 MHz
> acpicpu0: P3: FFH, lat  10 us, pow 62602 mW, 2700 MHz
> acpicpu0: P4: FFH, lat  10 us, pow 56402 mW, 2500 MHz
> acpicpu0: P5: FFH, lat  10 us, pow 53738 mW, 2400 MHz
> acpicpu0: P6: FFH, lat  10 us, pow 47885 mW, 2200 MHz
> acpicpu0: P7: FFH, lat  10 us, pow 45371 mW, 2100 MHz
> acpicpu0: P8: FFH, lat  10 us, pow 39867 mW, 1900 MHz
> acpicpu0: P9: FFH, lat  10 us, pow 34580 mW, 1700 MHz
> acpicpu0: P10: FFH, lat  10 us, pow 32326 mW, 1600 MHz
> acpicpu0: P11: FFH, lat  10 us, pow 27366 mW, 1400 MHz
> acpicpu0: P12: FFH, lat  10 us, pow 25267 mW, 1300 MHz
> acpicpu0: P13: FFH, lat  10 us, pow 20623 mW, 1100 MHz
> acpicpu0: P14: FFH, lat  10 us, pow 18664 mW, 1000 MHz
> acpicpu0: P15: FFH, lat  10 us, pow 14332 mW,  800 MHz
> coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
> acpicpu1 at cpu1: ACPI CPU
> coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=100
> acpicpu2 at cpu2: ACPI CPU
> coretemp2 at cpu2: thermal sensor, 1 C resolution, Tjmax=100
> acpicpu3 at cpu3: ACPI CPU
> coretemp3 at cpu3: thermal sensor, 1 C resolution, Tjmax=100
> timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
> timecounter: Timecounter "TSC" frequency 3000896830 Hz quality 3000
> uhub0 at usb0: vendor 8086 (0x8086) xHCI Root Hub (0000), class 9/0, rev 1.00/1.00, addr 0
> uhub0: 10 ports with 10 removable, self powered
> uhub1 at usb1: vendor 8086 (0x8086) xHCI Root Hub (0000), class 9/0, rev 2.00/1.00, addr 0
> uhub1: 16 ports with 16 removable, self powered
> IPsec: Initialized Security Association Processing.
> ahcisata0 port 0: device present, speed: 6.0Gb/s
> ahcisata0 port 5: device present, speed: 1.5Gb/s
> ahcisata0 port 4: PHY offline
> ahcisata0 port 1: PHY offline
> ahcisata0 port 3: PHY offline
> ahcisata0 port 2: PHY offline
> wd0 at atabus0 drive 0
> uhidev0 at uhub1 port 3 configuration 1 interface 0
> uhidev0: Fujitsu Technology Solutions GmbH (0xbf8) Fujitsu Keyboard (0x101e), rev 1.10/1.01, addr 1, iclass 3/1
> wd0: <ST1000NM0055-1V410C>
> wd0: drive supports 16-sector PIO transfers, LBA48 addressing
> wd0: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors
> ukbd0 at uhidev0
> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
> wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
> atapibus0 at atabus5: 1 targets
> cd0 at atapibus0 drive 0: <HL-DT-ST DVDRAM GUD0N, B7LRVC1426792, PF02> cdrom removable
> cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
> cd0(ahcisata0:5:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
> wskbd0 at ukbd0 mux 1
> wskbd0: connecting to wsdisplay0
> uhidev1 at uhub1 port 3 configuration 1 interface 1
> uhidev1: Fujitsu Technology Solutions GmbH (0xbf8) Fujitsu Keyboard (0x101e), rev 1.10/1.01, addr 1, iclass 3/0
> uhidev1: 5 report ids
> uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
> uhid1 at uhidev1 reportid 3: input=3, output=0, feature=0
> uhid2 at uhidev1 reportid 5: input=0, output=0, feature=5
> uhidev2 at uhub1 port 4 configuration 1 interface 0
> uhidev2: vendor 1241 (0x1241) product 1111 (0x1111), rev 1.00/1.00, addr 2, iclass 3/1
> ums0 at uhidev2: 3 buttons and Z dir
> wsmouse0 at ums0 mux 0
> pad0: outputs: 44100Hz, 16-bit, stereo
> audio0 at pad0: half duplex, playback, capture, mmap
> pad0: Virtual format configured - Format SLINEAR, precision 16, channels 2, frequency 44100
> pad0: Latency: 139 milliseconds
> spkr1 at audio0: PC Speaker (synthesized)
> WARNING: 6 errors while detecting hardware; check system log.
> boot device: wd0
> root on wd0a dumps on wd0b
> root file system type: ffs
> kern.module.path=/stand/amd64/8.0/modules
> wsdisplay0: screen 1 added (80x25, vt100 emulation)
> wsdisplay0: screen 2 added (80x25, vt100 emulation)
> wsdisplay0: screen 3 added (80x25, vt100 emulation)
> wsdisplay0: screen 4 added (80x25, vt100 emulation)
> You wrote:
>>
>> On Sun, 29 Apr 2018, Steve Blinkhorn wrote:
>>> Why might an LSI MegaRAID installation not be recognised in an
>>> attempted installation?   A RAID 1 array is set up using 2 identical disks
>>> recognised as properly configured by the BIOS; the install kernel is
>>> 8.0.
>>
>> Most (all?) recent LSI cards are not supported. See:
>> http://mail-index.netbsd.org/current-users/2018/02/19/msg033252.html
>>
>> There are some moves afoot to get drivers, so could you share the relevant
>> line from your dmesg so we can see what its product ID is?
>>
>> --
>> Stephen
>>
>>
>
>
> -- 
> Steve Blinkhorn <[email protected]>
>
>