Re: Nintendo WII: USB Keyboards not recognized on any USB ports

Hi Jared,

Thank you for letting me know about the update! I'll be happy to give it a =
try.

Thanks & Regards,
Melan Jayasinghage

On Sun, Sep 22, 2024 at 11:10=E2=80=AFPM Jared McNeill <jmcneill@invisible.=
ca> wrote:
>
> Hi Melan --
>
> I just added support for the onboard OHCI controller to NetBSD -current.
> Can you give it a try and let me know if it works for you?
>
> Thanks!
> Jared
>
> On Mon, 25 Mar 2024, Jared McNeill wrote:
>
> > Hi Melan --
> >
> > The onboard OHCI controller isn't supported yet, so you need to plug a =
USB
> > 2.0 (or better) hub into the Wii and then plug the USB keyboard into th=
e hub.
> >
> > Take care,
> > Jared
> >
> >
> > On Mon, 25 Mar 2024, Melan Jayasinghage wrote:
> >
> >>  Hello,
> >>
> >>  I hope this email finds you well.
> >>
> >>  Recently, I installed NetBSD  on my Nintendo Wii console. It seems
> >>  that USB keyboards connected to any of the USB ports on the Wii
> >>  console are not being recognized by NetBSD. I have attempted to
> >>  connect a few different USB keyboards, but unfortunately, none of the=
m
> >>  are being detected. I've verified that the USB port is functioning by
> >>  connecting an ethernet adapter and it was detected.
> >>
> >>  Could you please let me know if there is any additional configuration
> >>  required to enable USB keyboards support? Thank you.
> >>
> >>  =3D=3Ddmesg output=3D=3D
> >>  [     1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 200=
2,
> >>  2003,
> >>  [     1.000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2=
012,
> >>  2013,
> >>  [     1.000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2=
022,
> >>  2023,
> >>  [     1.000000]     2024
> >>  [     1.000000]     The NetBSD Foundation, Inc.  All rights reserved.
> >>  [     1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
> >>  [     1.000000]     The Regents of the University of California.  All
> >>  rights reserved.
> >>
> >>  [     1.000000] NetBSD 10.99.10 (WII) #0: Wed Mar 20 13:51:35 UTC 202=
4
> >>  [     1.000000]
> >>  [email protected]:/usr/src/sys/arch/evbppc/compile/WII
> >>  [     1.000000] total memory =3D 90112 KB
> >>  [     1.000000] avail memory =3D 67692 KB
> >>  [     1.000000] timecounter: Timecounters tick every 10.000 msec
> >>  [     1.000000] mainbus0 (root): Nintendo Wii
> >>  [     1.000000] cpu0 at mainbus0: 750 (Revision 2.0), ID 0 (primary)
> >>  [     1.000000] cpu0: HID0
> >>  0x8051c2e4<EMCP,NAP,DPM,NHR,ICE,DCE,SPD,SGE,DCFA,BTIC,BHT>, powersave=
:
> >>  1
> >>  [     1.000000] cpu0: 750.00 MHz, 256KB WB L2 cache
> >>  [     1.000000] genfb0 at mainbus0 addr 0x0c002000: NTSC 480i
> >>  [     1.000000] genfb0: framebuffer at 0x1698000, size 640x448, depth
> >>  16, stride 1280
> >>  [     1.000000] wsdisplay0 at genfb0 kbdmux 1: console (default, vt10=
0
> >>  emulation)
> >>  [     1.000000] wsmux1: connecting to wsdisplay0
> >>  [     1.000000] wsdisplay0: screen 1-3 added (default, vt100 emulatio=
n)
> >>  [     1.000000] exi0 at mainbus0 addr 0x0d006800 irq 4: External Inte=
rface
> >>  [     1.000000] rtcsram0 at exi0 addr 0-1: RTC/SRAM
> >>  [     1.000000] hollywood0 at mainbus0 irq 14: Hollywood ES2.1
> >>  [     1.000000] ehci0 at hollywood0 addr 0xd040000 irq 4: EHCI
> >>  [     1.000000] ehci0: EHCI version 1.0
> >>  [     1.000000] ehci0: 2 companion controllers, 2 ports each
> >>  [     1.000000] usb0 at ehci0: USB revision 2.0
> >>  [     1.000000] sdhc0 at hollywood0 addr 0xd070000 irq 7: SDHC
> >>  [     1.000000] sdhc0: SDHC 1.0, rev 0, caps <01e130b0/00000000>,
> >>  SDMA, 48000 kHz, HS 3.3V, 1024 byte blocks
> >>  [     1.000000] sdmmc0 at sdhc0 slot 0
> >>  [     1.000000] sdhc1 at hollywood0 addr 0xd080000 irq 8: SDHC
> >>  [     1.000000] sdhc1: SDHC 1.0, rev 0, caps <01e130b0/00000000>,
> >>  SDMA, 48000 kHz, HS 3.3V, 1024 byte blocks
> >>  [     1.000000] sdmmc1 at sdhc1 slot 0
> >>  [     1.000000] resetbtn0 at hollywood0 irq 17: Reset button
> >>  [     1.000000] hwgpio0 at hollywood0 addr 0xd0000c0 irq 10: GPIO
> >>  [     1.000000] gpio0 at hwgpio0: 24 pins
> >>  [     1.000000] gpioiic0 at gpio0 pins 14 15: SDA[15], SCL[14]
> >>  [     1.000000] iic0 at gpioiic0: I2C bus
> >>  [     1.000000] avenc0 at iic0 addr 0x70: A/V Encoder
> >>  [     1.000000] bwai0 at mainbus0 addr 0x0d006c00 irq 5: Audio Interf=
ace
> >>  [     1.000000] bwdsp0 at mainbus0 addr 0x0c005000 irq 6: DSP
> >>  [     1.000000] audio0 at bwdsp0: playback
> >>  [     1.000000] audio0: slinear_be:16 2ch 48000Hz, blk 1920 bytes
> >>  (10ms) for playback
> >>  [     1.000000] spkr0 at audio0: PC Speaker (synthesized)
> >>  [     1.000000] wsbell at spkr0 not configured
> >>  [     1.000000] vmmask 38000000 schedmask 7a000000 highmask 7e000000
> >>  [     1.000000] timecounter: Timecounter "mftb" frequency 60750000 Hz
> >>  quality 100
> >>  [     1.000003] timecounter: Timecounter "clockinterrupt" frequency
> >>  100 Hz quality 0
> >>  [     1.000003] WARNING: system needs entropy for security; see entro=
py(7)
> >>  [     1.000003] IPsec: Initialized Security Association Processing.
> >>  [     1.019992] uhub0 at usb0: NetBSD (0x0000) EHCI root hub (0x0000)=
,
> >>  class 9/0, rev 2.00/1.00, addr 1
> >>  [     1.019992] uhub0: 4 ports with 4 removable, self powered
> >>  [     1.109987] sdmmc0: SD card status: 4-bit, C10, U1
> >>  [     1.109987] ld0 at sdmmc0: <0x27:0x5048:SD32G:0x60:0x20a6096b:0x1=
64>
> >>  [     1.109987] ld0: 29820 MB, 7573 cyl, 128 head, 63 sec, 512
> >>  bytes/sect x 61071360 sectors
> >>  [     1.109987] ld0: 4-bit width, High-Speed/SDR25, 48.000 MHz
> >>  [     1.209988] sdmmc1: 4-bit width, 25.000 MHz
> >>  [     1.209988] sdmmc1: autoconfiguration error:
> >>  CISTPL_FUNCE(function) too short
> >>  [     1.209988] (manufacturer 0x2d0, product 0x44b) at sdmmc1 functio=
n
> >>  1 not configured
> >>  [     2.089987] axe0 at uhub0 port 2
> >>  [     2.089987] axe0: ASIX Electronics (0x0b95) AX88772 USB 2.0 10/10=
0
> >>  ethernet controller (0x7720), rev 2.00/0.01, addr 2
> >>  [     2.549988] ukphy0 at axe0 phy 16: Asix Semiconductor AX88772
> >>  internal PHY (OUI 0x007063, model 0x0001), rev. 1
> >>  [     2.559993] ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FD=
X,
> >>  auto
> >>  [     2.559993] axe0: Ethernet address 00:1b:7a:c6:c9:fa
> >>  [     3.149989] ehci0: handing over full speed device on port 3 to
> >>  companion controller
> >>  [     3.209990] WARNING: 1 error while detecting hardware; check syst=
em
> >>  log.
> >>  [     3.209990] boot device: ld0
> >>  [     3.209990] root on ld0a dumps on ld0b
> >>  [     3.209990] root file system type: ffs
> >>  [     3.230001] kern.module.path=3D/stand/evbppc/10.99.10/modules
> >>  [     4.060002] entropy: best effort
> >>  [     6.810043] wsdisplay0: screen 4 added (default, vt100 emulation)
> >>
> >>
> >>  Thanks & Regards,
> >>  Melan Jayasinghage
> >>
> >>
> >
> >