Re: Nintendo WII: USB Keyboards not recognized on any USB ports

Hi Melan --

I just added support for the onboard OHCI controller to NetBSD -current. 
Can you give it a try and let me know if it works for you?

Thanks!
Jared

On Mon, 25 Mar 2024, Jared McNeill wrote:

> Hi Melan --
>
> The onboard OHCI controller isn't supported yet, so you need to plug a USB 
> 2.0 (or better) hub into the Wii and then plug the USB keyboard into the hub.
>
> Take care,
> Jared
>
>
> On Mon, 25 Mar 2024, Melan Jayasinghage wrote:
>
>>  Hello,
>>
>>  I hope this email finds you well.
>>
>>  Recently, I installed NetBSD  on my Nintendo Wii console. It seems
>>  that USB keyboards connected to any of the USB ports on the Wii
>>  console are not being recognized by NetBSD. I have attempted to
>>  connect a few different USB keyboards, but unfortunately, none of them
>>  are being detected. I've verified that the USB port is functioning by
>>  connecting an ethernet adapter and it was detected.
>>
>>  Could you please let me know if there is any additional configuration
>>  required to enable USB keyboards support? Thank you.
>>
>>  ==dmesg output==
>>  [     1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002,
>>  2003,
>>  [     1.000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012,
>>  2013,
>>  [     1.000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022,
>>  2023,
>>  [     1.000000]     2024
>>  [     1.000000]     The NetBSD Foundation, Inc.  All rights reserved.
>>  [     1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
>>  [     1.000000]     The Regents of the University of California.  All
>>  rights reserved.
>>
>>  [     1.000000] NetBSD 10.99.10 (WII) #0: Wed Mar 20 13:51:35 UTC 2024
>>  [     1.000000]
>>  [email protected]:/usr/src/sys/arch/evbppc/compile/WII
>>  [     1.000000] total memory = 90112 KB
>>  [     1.000000] avail memory = 67692 KB
>>  [     1.000000] timecounter: Timecounters tick every 10.000 msec
>>  [     1.000000] mainbus0 (root): Nintendo Wii
>>  [     1.000000] cpu0 at mainbus0: 750 (Revision 2.0), ID 0 (primary)
>>  [     1.000000] cpu0: HID0
>>  0x8051c2e4<EMCP,NAP,DPM,NHR,ICE,DCE,SPD,SGE,DCFA,BTIC,BHT>, powersave:
>>  1
>>  [     1.000000] cpu0: 750.00 MHz, 256KB WB L2 cache
>>  [     1.000000] genfb0 at mainbus0 addr 0x0c002000: NTSC 480i
>>  [     1.000000] genfb0: framebuffer at 0x1698000, size 640x448, depth
>>  16, stride 1280
>>  [     1.000000] wsdisplay0 at genfb0 kbdmux 1: console (default, vt100
>>  emulation)
>>  [     1.000000] wsmux1: connecting to wsdisplay0
>>  [     1.000000] wsdisplay0: screen 1-3 added (default, vt100 emulation)
>>  [     1.000000] exi0 at mainbus0 addr 0x0d006800 irq 4: External Interface
>>  [     1.000000] rtcsram0 at exi0 addr 0-1: RTC/SRAM
>>  [     1.000000] hollywood0 at mainbus0 irq 14: Hollywood ES2.1
>>  [     1.000000] ehci0 at hollywood0 addr 0xd040000 irq 4: EHCI
>>  [     1.000000] ehci0: EHCI version 1.0
>>  [     1.000000] ehci0: 2 companion controllers, 2 ports each
>>  [     1.000000] usb0 at ehci0: USB revision 2.0
>>  [     1.000000] sdhc0 at hollywood0 addr 0xd070000 irq 7: SDHC
>>  [     1.000000] sdhc0: SDHC 1.0, rev 0, caps <01e130b0/00000000>,
>>  SDMA, 48000 kHz, HS 3.3V, 1024 byte blocks
>>  [     1.000000] sdmmc0 at sdhc0 slot 0
>>  [     1.000000] sdhc1 at hollywood0 addr 0xd080000 irq 8: SDHC
>>  [     1.000000] sdhc1: SDHC 1.0, rev 0, caps <01e130b0/00000000>,
>>  SDMA, 48000 kHz, HS 3.3V, 1024 byte blocks
>>  [     1.000000] sdmmc1 at sdhc1 slot 0
>>  [     1.000000] resetbtn0 at hollywood0 irq 17: Reset button
>>  [     1.000000] hwgpio0 at hollywood0 addr 0xd0000c0 irq 10: GPIO
>>  [     1.000000] gpio0 at hwgpio0: 24 pins
>>  [     1.000000] gpioiic0 at gpio0 pins 14 15: SDA[15], SCL[14]
>>  [     1.000000] iic0 at gpioiic0: I2C bus
>>  [     1.000000] avenc0 at iic0 addr 0x70: A/V Encoder
>>  [     1.000000] bwai0 at mainbus0 addr 0x0d006c00 irq 5: Audio Interface
>>  [     1.000000] bwdsp0 at mainbus0 addr 0x0c005000 irq 6: DSP
>>  [     1.000000] audio0 at bwdsp0: playback
>>  [     1.000000] audio0: slinear_be:16 2ch 48000Hz, blk 1920 bytes
>>  (10ms) for playback
>>  [     1.000000] spkr0 at audio0: PC Speaker (synthesized)
>>  [     1.000000] wsbell at spkr0 not configured
>>  [     1.000000] vmmask 38000000 schedmask 7a000000 highmask 7e000000
>>  [     1.000000] timecounter: Timecounter "mftb" frequency 60750000 Hz
>>  quality 100
>>  [     1.000003] timecounter: Timecounter "clockinterrupt" frequency
>>  100 Hz quality 0
>>  [     1.000003] WARNING: system needs entropy for security; see entropy(7)
>>  [     1.000003] IPsec: Initialized Security Association Processing.
>>  [     1.019992] uhub0 at usb0: NetBSD (0x0000) EHCI root hub (0x0000),
>>  class 9/0, rev 2.00/1.00, addr 1
>>  [     1.019992] uhub0: 4 ports with 4 removable, self powered
>>  [     1.109987] sdmmc0: SD card status: 4-bit, C10, U1
>>  [     1.109987] ld0 at sdmmc0: <0x27:0x5048:SD32G:0x60:0x20a6096b:0x164>
>>  [     1.109987] ld0: 29820 MB, 7573 cyl, 128 head, 63 sec, 512
>>  bytes/sect x 61071360 sectors
>>  [     1.109987] ld0: 4-bit width, High-Speed/SDR25, 48.000 MHz
>>  [     1.209988] sdmmc1: 4-bit width, 25.000 MHz
>>  [     1.209988] sdmmc1: autoconfiguration error:
>>  CISTPL_FUNCE(function) too short
>>  [     1.209988] (manufacturer 0x2d0, product 0x44b) at sdmmc1 function
>>  1 not configured
>>  [     2.089987] axe0 at uhub0 port 2
>>  [     2.089987] axe0: ASIX Electronics (0x0b95) AX88772 USB 2.0 10/100
>>  ethernet controller (0x7720), rev 2.00/0.01, addr 2
>>  [     2.549988] ukphy0 at axe0 phy 16: Asix Semiconductor AX88772
>>  internal PHY (OUI 0x007063, model 0x0001), rev. 1
>>  [     2.559993] ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
>>  auto
>>  [     2.559993] axe0: Ethernet address 00:1b:7a:c6:c9:fa
>>  [     3.149989] ehci0: handing over full speed device on port 3 to
>>  companion controller
>>  [     3.209990] WARNING: 1 error while detecting hardware; check system
>>  log.
>>  [     3.209990] boot device: ld0
>>  [     3.209990] root on ld0a dumps on ld0b
>>  [     3.209990] root file system type: ffs
>>  [     3.230001] kern.module.path=/stand/evbppc/10.99.10/modules
>>  [     4.060002] entropy: best effort
>>  [     6.810043] wsdisplay0: screen 4 added (default, vt100 emulation)
>> 
>>
>>  Thanks & Regards,
>>  Melan Jayasinghage
>> 
>> 
>
>