Re: Xfree86 broken in 5.0-rc2 binary sets?

--- On Thu, 2/19/09, Michael <[email protected]> wrote:

> From: Michael <[email protected]>
> Subject: Re: Xfree86 broken in 5.0-rc2 binary sets?
> To: "Andrew Randrianasulu" <[email protected]>
> Cc: [email protected]
> Date: Thursday, February 19, 2009, 1:55 AM
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
> 
> Hello,
> 
> On Feb 18, 2009, at 8:46 PM, Andrew Randrianasulu wrote:
> 
> > Hello!
> > 
> > I have netbsd-5/sgimips as completely network-based
> install: tftpd for booting kernel, NFS for root fs. It works
> fine on my sgi o2. But Xfree give me error  at X -configure
> stage:
> > 
> > -----
> > (II) Loading
> /usr/X11R6/lib/modules/drivers/libwsfb_drv.so I am at
> 0x4829b4
> > dlopen: /usr/X11R6/lib/modules/drivers/libwsfb_drv.so:
> Undefined symbol "shadowU
> > pdatePacked" (symnum = 47)
> > (EE) Failed to load
> /usr/X11R6/lib/modules/drivers/libwsfb_drv.so
> > (II) UnloadModule: "libwsfb"
> > (EE) Failed to load module "libwsfb" (loader
> failed, 7)
> > -----
> > and
> > 
> > No devices to configure.  Configuration failed.
> 
> Known problem, the MIPS-specific module loader in XFree86
> is quite broken. It works in Xorg though. Also, wsfb on
> crmfb doesn't currently work anyway - wsfb expects a
> linear framebuffer which crmfb does not provide - it uses
> CRIME's native tiled format. You can use experimental X
> binaries from
> ftp://ftp.netbsd.org/pub/NetBSD/misc/macallan/sgimips/
> which provide quite a bit of hardware acceleration (
> including xrender ) but still have some glitches. So far I
> didn't get around to fix that properly.

Yes, crime_drv.so works, with some bugs. (for example using gimp's screenshot function caused whole X to freeze). I want to help you with this
driver, but  probably i need more recent kernel and (native) Xorg first? Compiling this will take some time even on my x86 box .... And for some reason i still don't have internet access under NetBSD. I can netboot, of course, /etc/hosts was edited with correct hostname (before all X programs were very slow at startup), i have correct IP address (192.168.1.3), resolv.conf with one entry "nameserver 192.168.1.1" and default route to  
192.168.1.1 (my router). But i can't ping neither router, nor outside network. Strange, but Irix with same settings can reach Internet (and cause my router to freeze (!) after some Netscape activity ... router = small box labeled "WBR-3405TX", from LevelOne. May be just broken hardware inside it. Very easy to freeze, and no way to reconfigure after this, only full reset.)
> 
> have fun
> Michael
> 
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.4.7 (Darwin)
> 
> iQEVAwUBSZy8LMpnzkX8Yg2nAQJ54gf+JxVLvzW7w7vrdLJTHzeagOz2eHRhmPX7
> DKprc7qlX2uIZK4vk8BL48Iep02cnvwH1sC2NPqW5aXrBYQTo52secnCYGYeygzP
> H9cuZ3au8hq3mSPuM2q+EZP2Ylj8foz29zEjDY9IcWU8pfnv9Sfeukk2Ls/86Ggn
> lLfM9Al31ZsVK5wYUm80wqqGhgauMGokGxBHgKTzBXc1Z9z16rsJZS/RuhGIDr7M
> bm8Vpej4vD4D8wvqHSrp/GcHF8uVqgShZuWBIvIvKyXS07yYcnjM+9FinNQieLML
> +jatQJZH3Zjpjrqmeajntj4FNYB3H/opwn7LqxIWyfsUjhNmct5LBA==
> =lSkg
> -----END PGP SIGNATURE-----