Re: Whats about Cyrix ?

On Wed, 3 Jul 2002 19:54:32 +0200
"Ralf Riedel" <[email protected]> wrote:

> does NetBSD works on a Cyrix MediaGX 233MHz with the companion Chip
> CX5530 (National Semiconductors). 

Here is a dmesg of a system I have here, which has been running for quite
a while, and very stably despite the cheap architecture:

NetBSD 1.5.2 (mmondor.gobot) #2: Sun Apr 21 17:38:46 EDT 2002
    [email protected]:/data/src/sys/arch/i386/compile/mmondor.gobot
cpu0: Cyrix MMX-enhanced MediaGX (GXm) (586-class), 233.87 MHz
total memory = 127 MB
avail memory = 115 MB
using 1659 buffers containing 6636 KB of memory
BIOS32 rev. 0 found at 0xfb510
mainbus0 (root)
pnpbios0 at mainbus0: nodes 18, max len 78
com5 at pnpbios0 index 16 (PNP0501)
com5: io 3f8-3ff, irq 4
com5: ns16550a, working fifo
lpt3 at pnpbios0 index 18 (PNP0400)
lpt3: io 378-37f, irq 7
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1078 product 0x0001 (rev. 0x00)
ne2 at pci0 dev 7 function 0: RealTek 8029 Ethernet
ne2: 10base2, 10baseT, 10baseT-FDX, auto, default [0x00 0x30] auto
ne2: Ethernet address 00:e0:29:4f:36:b9
ne2: interrupting at irq 10
vga1 at pci0 dev 8 function 0: vendor 0x1002 product 0x4750 (rev. 0x5c)
wsdisplay0 at vga1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 18 function 0
pcib0: vendor 0x1078 product 0x0002 (rev. 0x00)
isa0 at pcib0
ne0 at isa0 port 0x280-0x29f irq 9
ne0: NE2000 Ethernet
ne0: Ethernet address 00:80:29:64:cb:fa
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
wd0 at wdc0 channel 0 drive 0: <FUJITSU MPD3043AT>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 4125 MB, 8940 cyl, 15 head, 63 sec, 512 bytes/sect x 8448300 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4
wdc1 at isa0 port 0x170-0x177 irq 15
wd1 at wdc1 channel 0 drive 1: <FUJITSU MPE3064AT>
wd1: drive supports 16-sector pio transfers, lba addressing
wd1: 6187 MB, 13410 cyl, 15 head, 63 sec, 512 bytes/sect x 12672450 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: read port 0x203
isapnp0: <CMI8330. Audio Adapter, @@@0001, , > port 0x530/8,0x388/8 irq 11 drq 0 not configured
isapnp0: <CMI8330. Audio Adapter, @H@0001, , > port 0x330/2 irq 9 not configured
isapnp0: <CMI8330. Audio Adapter, @P@0001, , > port 0x200/8 not configured
sb1 at isapnp0 port 0x220/16 irq 5 drq 1,5
sb1: CMI8330. Audio Adapter : dsp v4.13
audio0 at sb1: full duplex, mmap, independent
midi0 at sb1: SB MIDI UART
opl0 at sb1: model OPL3
midi at opl0 not configured
biomask e94d netmask ef4d ttymask ffcf
IPsec: Initialized Security Association Processing.
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs

Sound also works fine.