cbb on b180l problem

cbb0 at pci0 dev 1 function 0 "Texas Instruments PCI1410 CardBus" rev 0x01: couldn't establish interrupt at irq 256

any ideas?

Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2004 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 3.6-current (GENERIC) #181: Sat Oct 30 04:23:34 MDT 2004
    [email protected]:/usr/src/sys/arch/hppa/compile/GENERIC
HP 9000/778/B180L+ (Merlin L2+ 180) PA-RISC 1.1e
real mem = 268435456 (524288 reserved for PROM, 6184960 used by OpenBSD)
avail mem = 228274176
using 8421 buffers containing 26828800 bytes of memory
mainbus0 (root) [flex fff80000]
pdc0 at mainbus0
power0 at mainbus0 offset 140000
mem0 at mainbus0 offset ffbf000: size 256MB, 1MB L2 cache
cpu0 at mainbus0 offset ffbe000 irq 31: PCXL2 L1-A 180MHz, FPU VR rev 1
cpu0: 64K(32b/l) Icache, 64K(32b/l) wr-back Dcache, 96 coherent TLB, 8 BTLB
phantomas0 at mainbus0 offset fc00000
sti0 at phantomas0 offset 8000000 irq 11: INTERNAL_EG_1280 rev 8.07;9, ID 0x2D08C0A709A02587
sti0: 2048x2048 frame buffer, 1280x1024x8 display, offset 0x0
sti0: 8x16 font type 1, 16 bpc, charset 0-255
lasi0 at phantomas0 offset fd00000 irq 28: rev 3.0
gsc0 at lasi0: wordleds
gsckbc0 at gsc0 offset 8100 irq 26
gsckbc1 at gsc0 offset 8000 irq 26
osiop0 at gsc0 offset 6000 irq 9: NCR53C710 rev 2, 40MHz, SCSI ID 7
scsibus0 at osiop0: 8 targets
osiop0: target 2 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
cd0 at scsibus0 targ 2 lun 0: <TOSHIBA, CD-ROM XM-6201TA, 1037> SCSI2 5/cdrom removable
com0 at gsc0 offset 5000 irq 5: ns16550a, 16 byte fifo
com0: console
harmony0 at gsc0 offset 4000 irq 13: rev 0
audio0 at harmony0
lpt0 at gsc0 offset 2000 irq 7
dino0 at phantomas0 offset ff80000 irq 25: Dino V3.1
com1 at dino0 irq 11: ns16550a, 16 byte fifo
pci0 at dino0
cbb0 at pci0 dev 1 function 0 "Texas Instruments PCI1410 CardBus" rev 0x01: couldn't establish interrupt at irq 256
siop0 at pci0 dev 19 function 0 "Symbios Logic 53c875" rev 0x04: irq 4, using 4K of on-board RAM
scsibus1 at siop0: 16 targets
sd0 at scsibus1 targ 6 lun 0: <SEAGATE, ST34572WS, HP00> SCSI2 0/direct fixed
sd0: 4095MB, 6300 cyl, 8 head, 166 sec, 512 bytes/sec, 8388314 sec total
dc0 at pci0 dev 20 function 0 "DEC 21142/3" rev 0x41: irq 1, address 00:10:83:03:ed:5c
lxtphy0 at dc0 phy 1: LXT970 10/100 PHY, rev. 1
biomask 0xb netmask 0xf ttymask 0x3f
boot path: 8/0/19/0.6 class=1 flags=c0<autoboot,autosearch> hpa=0xf0ffd000 spa=0x0 io=0x12000
root on sd0a swap on sd0b
siop0: target 6 now using tagged 16 bit 20.0 MHz 15 REQ/ACK offset xfers
wsdisplay0 at sti0
wsdisplay0: screen 0 added (default, vt100 emulation)
rootdev=0x400 rrootdev=0xa00 rawdev=0xa02