Re: cbb on b180l problem

Making, drinking tea and reading an opus magnum from Jolan Luff:
> cbb0 at pci0 dev 1 function 0 "Texas Instruments PCI1410 CardBus" rev 0x01: couldn't establish interrupt at irq 256
> 
> any ideas?

same problem as on i386 -- prom does not setup the irqs
current cbb support was primarily done for the onboard
controller on the rdi precision book that seems to work (;

cu

> Copyright (c) 1982, 1986, 1989, 1991, 1993
>         The Regents of the University of California.  All rights reserved.
> Copyright (c) 1995-2004 OpenBSD. All rights reserved.  http://www.OpenBSD.org
> 
> OpenBSD 3.6-current (GENERIC) #181: Sat Oct 30 04:23:34 MDT 2004
>     [email protected]:/usr/src/sys/arch/hppa/compile/GENERIC
> HP 9000/778/B180L+ (Merlin L2+ 180) PA-RISC 1.1e
> real mem = 268435456 (524288 reserved for PROM, 6184960 used by OpenBSD)
> avail mem = 228274176
> using 8421 buffers containing 26828800 bytes of memory
> mainbus0 (root) [flex fff80000]
> pdc0 at mainbus0
> power0 at mainbus0 offset 140000
> mem0 at mainbus0 offset ffbf000: size 256MB, 1MB L2 cache
> cpu0 at mainbus0 offset ffbe000 irq 31: PCXL2 L1-A 180MHz, FPU VR rev 1
> cpu0: 64K(32b/l) Icache, 64K(32b/l) wr-back Dcache, 96 coherent TLB, 8 BTLB
> phantomas0 at mainbus0 offset fc00000
> sti0 at phantomas0 offset 8000000 irq 11: INTERNAL_EG_1280 rev 8.07;9, ID 0x2D08C0A709A02587
> sti0: 2048x2048 frame buffer, 1280x1024x8 display, offset 0x0
> sti0: 8x16 font type 1, 16 bpc, charset 0-255
> lasi0 at phantomas0 offset fd00000 irq 28: rev 3.0
> gsc0 at lasi0: wordleds
> gsckbc0 at gsc0 offset 8100 irq 26
> gsckbc1 at gsc0 offset 8000 irq 26
> osiop0 at gsc0 offset 6000 irq 9: NCR53C710 rev 2, 40MHz, SCSI ID 7
> scsibus0 at osiop0: 8 targets
> osiop0: target 2 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
> cd0 at scsibus0 targ 2 lun 0: <TOSHIBA, CD-ROM XM-6201TA, 1037> SCSI2 5/cdrom removable
> com0 at gsc0 offset 5000 irq 5: ns16550a, 16 byte fifo
> com0: console
> harmony0 at gsc0 offset 4000 irq 13: rev 0
> audio0 at harmony0
> lpt0 at gsc0 offset 2000 irq 7
> dino0 at phantomas0 offset ff80000 irq 25: Dino V3.1
> com1 at dino0 irq 11: ns16550a, 16 byte fifo
> pci0 at dino0
> cbb0 at pci0 dev 1 function 0 "Texas Instruments PCI1410 CardBus" rev 0x01: couldn't establish interrupt at irq 256
> siop0 at pci0 dev 19 function 0 "Symbios Logic 53c875" rev 0x04: irq 4, using 4K of on-board RAM
> scsibus1 at siop0: 16 targets
> sd0 at scsibus1 targ 6 lun 0: <SEAGATE, ST34572WS, HP00> SCSI2 0/direct fixed
> sd0: 4095MB, 6300 cyl, 8 head, 166 sec, 512 bytes/sec, 8388314 sec total
> dc0 at pci0 dev 20 function 0 "DEC 21142/3" rev 0x41: irq 1, address 00:10:83:03:ed:5c
> lxtphy0 at dc0 phy 1: LXT970 10/100 PHY, rev. 1
> biomask 0xb netmask 0xf ttymask 0x3f
> boot path: 8/0/19/0.6 class=1 flags=c0<autoboot,autosearch> hpa=0xf0ffd000 spa=0x0 io=0x12000
> root on sd0a swap on sd0b
> siop0: target 6 now using tagged 16 bit 20.0 MHz 15 REQ/ACK offset xfers
> wsdisplay0 at sti0
> wsdisplay0: screen 0 added (default, vt100 emulation)
> rootdev=0x400 rrootdev=0xa00 rawdev=0xa02
> 


-- 
    paranoic mickey       (my employers have changed but, the name has remained)