Re: Recent mac68k improvements

On Wed, Dec 08, 2004 at 08:53:05PM +0000, Miod Vallat wrote:
> Hello,
> 
>   So, if you have a machine to upgrade or to install, please give the
> latest OpenBSD/mac68k snapshot a try. Say goodbye to the Mac OS tools
> (except for the booter), enjoy bsd.rd, and let us know of your results.
> 
>   Your mileage may vary, though: this snapshot has issues on the AV
> machines, and depending upon how much memory you have in your machine,
> bsd.rd may not run. These problems have already been fixed, and a new
> snapshot will be available soon. We are also working on the rough edges
> of the installation procedure, in order to make it easier by the time
> OpenBSD 3.7 hits the stack.

I took something dated Dec 7 9:17 from ftp5.usa and went nowhere with it.

Do I need a new Mac Booter? The utils dir had the same 1.11.3 so I
didn't bother to unhex it.

Are there special options to use in the Mac booter? Beside pointing
it to the right file.

When booting the bsd.rd, it prints the Copyrights notices and then
nothing. I have to reset the machine.  I can load the bsd kernel fine.

That's on my Quadra 650 with 24MB of memory.

This is the dmesg from "bsd":

OpenBSD 3.6-current (GENERIC) #1: Mon Dec  6 15:10:53 EST 2004
    [email protected]:/usr/src/sys/arch/mac68k/compile/GENERIC
Apple Macintosh Quadra 650, 68040 CPU+MMU+FPU, 4k on-chip physical I/D caches
real mem = 25165824 (24576K)
avail mem = 17510400 (17100K)
using 307 buffers containing 1257472 bytes (1228K) of memory
mrg: 'Quadra/Centris ROMs' ROM glue, tracing off, debug off, silent traps
mrg: I/O map kludge for ROMs that use hardware addresses directly.
adb: bus subsystem
mrg: skipping egret setup
adb: calling ADBReInit
adb: using II series hardware support
adb: cleanup: nothing returned
adb: ADBReInit complete
adb: mapped device (5) at 2
adb: 100 dpi mouse at 3
mainbus0 (root)
obio0 at mainbus0
adb0 at obio0 (ADB event device)
asc0 at obio0: Apple Sound Chip
intvid0 at obio0: DAFB: Monitor sense 1.
intvid0: 640 x 480, monochrome
grf0 at intvid0
ite0 at grf0 (minimal console)
sn0 at obio0: integrated ethernet adapter, address 08:00:07:9c:f8:76
esp0 at obio0: address 0x898000: NCR53C96, 16MHz, SCSI ID 7
scsibus0 at esp0: 8 targets
sd0 at scsibus0 targ 2 lun 0: <IBM, DPES-31080 !t, S31R> SCSI2 0/direct fixed
sd0: 1034MB, 4903 cyl, 4 head, 108 sec, 512 bytes/sec, 2118144 sec total
cd0 at scsibus0 targ 3 lun 0: <SONY, CD-ROM CDU-8003A, 1.9a> SCSI2 5/cdrom removable
zsc0 at obio0
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
nubus0 at mainbus0
root on sd0a swap on sd0b
PRAM: 0x41b8eb06, macos_boottime: 0x41b8eafe.

At the top, there's debugging info about the memory that didn't
show there. Only with bsd, not with bsd.rd.


-- 
Hugo Villeneuve <[email protected]>
http://EINTR.net/