Re: SMP on Compaq 1850R

> -----Original Message-----
> From: [email protected] [mailto:[email protected]] On 
> Behalf Of Daniel Leeds
> Sent: Tuesday, November 02, 2004 9:53 AM
> To: Mark Keating
> Cc: [email protected]
> Subject: Re: SMP on Compaq 1850R
> 
> Mark Keating wrote:
> 
> >
> >I will test it on the same system tomorrow.  Was this installed from 
> >the 3.6 CD?
> >  
> >
> I created a boot floppy and then did an ftp install over the net.
> 
> 
>
Daniel,

I was able to get both processors recognized by using the OS setting of
'other' and the APIC mode to 'full table - mapped' in the system
configuration utility(scu).  You can run scu by booting to a SmartStart CD
or by creating the disketes using the file at
http://h18023.www1.hp.com/support/files/server/us/download/13227.html  When
you run scu, hit ctrl-a to enter advanced mode, select the sytem
configuration option from the menu, select the option to review the setings,
scroll down to the APIC mode and set it 'full table - mapped'.  The system
should then be able to see both processors.

Mark

OpenBSD 3.6 (GENERIC.MP) #173: Fri Sep 17 12:52:31 MDT 2004
    [email protected]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel Pentium III ("GenuineIntel" 686-class, 512KB L2 cache) 499 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,
FXSR,SSE
real mem  = 268001280 (261720K)
avail mem = 237600768 (232032K)
using 3297 buffers containing 13504512 bytes (13188K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000
pcibios0: PCI BIOS has 7 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:20:0 ("Intel 82371AB PIIX4 ISA" rev
0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xe8000/0x6000 0xee000/0x2000!
mainbus0: Intel MP Specification (Version 1.4) (COMPAQ   PROLIANT    )
cpu0 at mainbus0: apid 1 (boot processor)
cpu0: apic clock running at 99 MHz
cpu1 at mainbus0: apid 0 (application processor)
cpu1: Intel Pentium III ("GenuineIntel" 686-class, 512KB L2 cache) 498 MHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,
FXSR,SSE
mainbus0: bus 0 is type PCI   
mainbus0: bus 9 is type ISA   
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 11, 35 pins
ioapic0: misconfigured as apic 0, remapped to apic 8
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX" rev 0x02
siop0 at pci0 dev 6 function 0 "Symbios Logic 53c875" rev 0x14: apic 8 int 5
(irq 5), using 4K of on-board RAM
scsibus0 at siop0: 16 targets
sd0 at scsibus0 targ 1 lun 0: <COMPAQ, BD018122C0, 3B12> SCSI2 0/direct
fixed
sd0: 17365MB, 7001 cyl, 20 head, 254 sec, 512 bytes/sec, 35565080 sec total
siop1 at pci0 dev 6 function 1 "Symbios Logic 53c875" rev 0x14: apic 8 int
10 (irq 10), using 4K of on-board RAM
scsibus1 at siop1: 16 targets
tl0 at pci0 dev 7 function 0 "Compaq ProLiant Netelligent 10/100 TX" rev
0x10: apic 8 int 11 (irq 11) address 00:80:5f:65:6b:4c
lxtphy0 at tl0 phy 1: LXT970 10/100 media interface, rev. 0
ukphy0 at tl0 phy 31: Generic IEEE 802.3u media interface
ukphy0: OUI 0x100014, model 0x0001, rev. 5
vga1 at pci0 dev 8 function 0 "ATI Mach64 GV" rev 0x3a
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"Compaq Netelligent ASMC" rev 0x00 at pci0 dev 9 function 0 not configured
pcib0 at pci0 dev 20 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 20 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel
0 wired to compatibility, channel 1 wired to compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus2 at atapiscsi0: 2 targets
cd0 at scsibus2 targ 0 lun 0: <COMPAQ, CD-224E, 8.0J> SCSI0 5/cdrom
removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
uhci0 at pci0 dev 20 function 2 "Intel 82371AB USB" rev 0x01pci_intr_map: no
mapping for pin D
: couldn't map interrupt
"Intel 82371AB Power Mgmt" rev 0x02 at pci0 dev 20 function 3 not configured
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 0 netmask 0 ttymask 0
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
siop0: target 1 now using tagged 16 bit 20.0 MHz 15 REQ/ACK offset xfers
dkcsum: sd0 matched BIOS disk 80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02