Dell Inspiron 3000 running 3.8

USB does not seem to work (it may be the machine it had
a hard life). USB does not recognize any devices when they 
are plugged in. 

zzz and lid shutting do not work. System hangs, a hard restart
is necessary. Maybe it needs configuration, I haven't done any

Worked fine on auto generated xorg.conf


OpenBSD 3.8 (GENERIC) #138: Sat Sep 10 15:41:37 MDT 2005
    [email protected]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 267 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX
cpu0: F00F bug workaround installed
real mem  = 83468288 (81512K)
avail mem = 68759552 (67148K)
using 1044 buffers containing 4276224 bytes (4176K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(76) BIOS, date 11/07/97, BIOS32 rev. 0 @
0xfd800
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 100%
apm0: AC on, battery charge high, estimated 6:40 hours
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xfd800/0x800
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf90/80 (3 entries)
pcibios0: PCI Interrupt Router at 000:01:0 ("Intel 82371FB ISA" rev
0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xc000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82439TX System" rev 0x01
pcib0 at pci0 dev 1 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01
pciide0 at pci0 dev 1 function 1 "Intel 82371AB IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DTCA-24090>
wd0: 16-sector PIO, LBA, 3909MB, 8007552 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
uhci0 at pci0 dev 1 function 2 "Intel 82371AB USB" rev 0x01: irq 10
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82371AB Power" rev 0x01 at pci0 dev 1 function 3 not configured
vga1 at pci0 dev 2 function 0 "Neomagic Magicgraph NM2160" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
cbb0 at pci0 dev 4 function 0 "Texas Instruments PCI1131 CardBus" rev
0x01: irq 11
cbb1 at pci0 dev 4 function 1 "Texas Instruments PCI1131 CardBus" rev
0x01: irq 11
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x0, lattimer 0x20
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 2 device 0 cacheline 0x0, lattimer 0x20
pcmcia1 at cardslot1
biomask efed netmask efed ttymask ffef
pctr: 586-class performance counters and user-level cycle counter
enabled
ep1 at pcmcia0 function 0 "3Com Corporation, 3C562D/3C563D, EtherLink
III" port 0xa000/16: address 00:60:97:f9:78:55, utp/aui/bnc (default
utp)
pccom3 at pcmcia0 function 1 "3Com Corporation, 3C562D/3C563D, EtherLink
III" port 0xa2f8/8: ns16550a, 16 byte fifo
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302