[PATCH] staging: rtl8723bs: Rename variable supportRateNum

Rename the variable `supportRateNum` to `support_rate_num` to adhere to
Linux kernel coding standards by using snake_case instead of CamelCase.

Fixes checkpatch.pl warning:
    CHECK: Avoid CamelCase: <supportRateNum>

Signed-off-by: Erick Karanja <[email protected]>
---
 drivers/staging/rtl8723bs/core/rtw_ap.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/drivers/staging/rtl8723bs/core/rtw_ap.c b/drivers/staging/rtl8723bs/core/rtw_ap.c
index 50022bb5911e..5124260602c8 100644
--- a/drivers/staging/rtl8723bs/core/rtw_ap.c
+++ b/drivers/staging/rtl8723bs/core/rtw_ap.c
@@ -370,7 +370,7 @@ void add_RATid(struct adapter *padapter, struct sta_info *psta, u8 rssi_level)
 void update_bmc_sta(struct adapter *padapter)
 {
 	unsigned char network_type;
-	int supportRateNum = 0;
+	int support_rate_num = 0;
 	unsigned int tx_ra_bitmap = 0;
 	struct mlme_priv *pmlmepriv = &padapter->mlmepriv;
 	struct mlme_ext_priv *pmlmeext = &padapter->mlmeextpriv;
@@ -396,9 +396,9 @@ void update_bmc_sta(struct adapter *padapter)
 		/* psta->dot118021XPrivacy = _NO_PRIVACY_;//!!! remove it, because it has been set before this. */
 
 		/* prepare for add_RATid */
-		supportRateNum = rtw_get_rateset_len((u8 *)&pcur_network->supported_rates);
+		support_rate_num = rtw_get_rateset_len((u8 *)&pcur_network->supported_rates);
 		network_type = rtw_check_network_type((u8 *)&pcur_network->supported_rates,
-						      supportRateNum,
+						      support_rate_num,
 						      pcur_network->configuration.ds_config
 		);
 		if (is_supported_tx_cck(network_type)) {
@@ -893,7 +893,7 @@ int rtw_check_beacon_data(struct adapter *padapter, u8 *pbuf,  int len)
 	);
 	if (p) {
 		memcpy(supportRate, p + 2, ie_len);
-		supportRateNum = ie_len;
+		support_rate_num = ie_len;
 	}
 
 	/* get ext_supported rates */
@@ -904,11 +904,12 @@ int rtw_check_beacon_data(struct adapter *padapter, u8 *pbuf,  int len)
 		pbss_network->ie_length - _BEACON_IE_OFFSET_
 	);
 	if (p) {
-		memcpy(supportRate + supportRateNum, p + 2, ie_len);
-		supportRateNum += ie_len;
+		memcpy(supportRate + support_rate_num, p + 2, ie_len);
+		support_rate_num += ie_len;
 	}
 
-	network_type = rtw_check_network_type(supportRate, supportRateNum, channel);
+	network_type = rtw_check_network_type(supportRate, support_rate_num,
+					      channel);
 
 	rtw_set_supported_rate(pbss_network->supported_rates, network_type);
 
-- 
2.43.0