[PATCH v4 14/21] pinctrl: starfive: Add StarFive JHB100 per1 controller driver

Add pinctrl driver for StarFive JHB100 SoC Peripheral-1(per1) pinctrl
controller.

Co-developed-by: Lianfeng Ouyang <[email protected]>
Signed-off-by: Lianfeng Ouyang <[email protected]>
Signed-off-by: Alex Soo <[email protected]>
Signed-off-by: Changhuang Liang <[email protected]>
---
 drivers/pinctrl/starfive/Kconfig              |  11 ++
 drivers/pinctrl/starfive/Makefile             |   1 +
 .../starfive/pinctrl-starfive-jhb100-per1.c   | 163 ++++++++++++++++++
 3 files changed, 175 insertions(+)
 create mode 100644 drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per1.c

diff --git a/drivers/pinctrl/starfive/Kconfig b/drivers/pinctrl/starfive/Kconfig
index ddd39807e222..0fe2d21ba402 100644
--- a/drivers/pinctrl/starfive/Kconfig
+++ b/drivers/pinctrl/starfive/Kconfig
@@ -68,6 +68,17 @@ config PINCTRL_STARFIVE_JHB100_PER0
 	  peripherals supporting inputs, outputs, configuring pull-up/pull-down
 	  and interrupts on input changes.
 
+config PINCTRL_STARFIVE_JHB100_PER1
+	tristate "StarFive JHB100 SoC Peripheral-1 pinctrl and GPIO driver"
+	depends on ARCH_STARFIVE || COMPILE_TEST
+	select PINCTRL_STARFIVE_JHB100
+	default ARCH_STARFIVE
+	help
+	  Say yes here to support Peripheral-1 pin control on the StarFive JHB100 SoC.
+	  This also provides an interface to the GPIO pins not used by other
+	  peripherals supporting inputs, outputs, configuring pull-up/pull-down
+	  and interrupts on input changes.
+
 config PINCTRL_STARFIVE_JHB100_SYS0
 	tristate "StarFive JHB100 SoC System-0 pinctrl and GPIO driver"
 	depends on ARCH_STARFIVE || COMPILE_TEST
diff --git a/drivers/pinctrl/starfive/Makefile b/drivers/pinctrl/starfive/Makefile
index f2bb0c35a2a0..6beef7e313ef 100644
--- a/drivers/pinctrl/starfive/Makefile
+++ b/drivers/pinctrl/starfive/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_PINCTRL_STARFIVE_JH7110_AON)	+= pinctrl-starfive-jh7110-aon.o
 
 obj-$(CONFIG_PINCTRL_STARFIVE_JHB100)		+= pinctrl-starfive-jhb100.o
 obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER0)	+= pinctrl-starfive-jhb100-per0.o
+obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_PER1)	+= pinctrl-starfive-jhb100-per1.o
 obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0)	+= pinctrl-starfive-jhb100-sys0.o
 obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS0H)	+= pinctrl-starfive-jhb100-sys0h.o
 obj-$(CONFIG_PINCTRL_STARFIVE_JHB100_SYS1)	+= pinctrl-starfive-jhb100-sys1.o
diff --git a/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per1.c b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per1.c
new file mode 100644
index 000000000000..d1f722a7ccc6
--- /dev/null
+++ b/drivers/pinctrl/starfive/pinctrl-starfive-jhb100-per1.c
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Pinctrl / GPIO driver for StarFive JHB100 SoC Peripheral-1 domain
+ *
+ * Copyright (C) 2024 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <[email protected]>
+ *
+ */
+
+#include <dt-bindings/pinctrl/starfive,jhb100-pinctrl.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-starfive-jhb100.h"
+
+static const struct jhb100_pin_layout_desc jhb100_per1_pl_desc[] = {
+	{ .pin_start = 0, .pin_cnt = 36, .name = "gpio", .gpio_func_sel = 0 },
+	{ 0xff },
+};
+
+static const struct config_reg_layout_desc jhb100_per1_pinctr_rldesc[] = {
+	{
+		.pin_start					= 0,
+		.pin_cnt					= 32,
+		.fields[PAD_CFG_DRIVE_STRENGTH_2BIT]		= { .shift = 0, .width = 2 },
+		.fields[PAD_CFG_INPUT_ENABLE]			= { .shift = 2, .width = 1 },
+		.fields[PAD_CFG_PULL_DOWN]			= { .shift = 3, .width = 1 },
+		.fields[PAD_CFG_PULL_UP]			= { .shift = 4, .width = 1 },
+		.fields[PAD_CFG_SLEW_RATE]			= { .shift = 5, .width = 1 },
+		.fields[PAD_CFG_SCHMITT_TRIGGER_SELECT]		= { .shift = 6, .width = 1 },
+		.fields[PAD_CFG_DEBOUNCE_WIDTH]			= { .shift = 15, .width = 17 },
+	},
+	{
+		.pin_start					= 32,
+		.pin_cnt					= 4,
+		.fields[PAD_CFG_INPUT_ENABLE]			= { .shift = 0, .width = 1 },
+		.fields[PAD_CFG_MODE_SELECT]			= { .shift = 1, .width = 2 },
+		.fields[PAD_CFG_PULL_DOWN]			= { .shift = 3, .width = 1 },
+		.fields[PAD_CFG_PULL_UP]			= { .shift = 4, .width = 1 },
+		.fields[PAD_CFG_OPEN_DRAIN_PULL_UP_SEL]		= { .shift = 5, .width = 2 },
+		.fields[PAD_CFG_SCHMITT_TRIGGER_SELECT]		= { .shift = 7, .width = 1 },
+		.fields[PAD_CFG_DEBOUNCE_WIDTH]			= { .shift = 15, .width = 17 },
+	},
+	{ 0xff },
+};
+
+static const struct pinvref_desc pinvref_desc_per1[] = {
+	{
+		/* gpioe-spi */
+		.pin_grp = {
+			PADNUM_PER1_GPIO_C0,
+			PADNUM_PER1_GPIO_C1,
+			PADNUM_PER1_GPIO_C2,
+			PADNUM_PER1_GPIO_C3,
+			PADNUM_PER1_GPIO_C4
+		},
+		.num_pins = 5,
+		.range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+	},
+	{
+		/* gpioe-qspi0 */
+		.pin_grp = {
+			PADNUM_PER1_GPIO_C5,
+			PADNUM_PER1_GPIO_C6,
+			PADNUM_PER1_GPIO_C7,
+			PADNUM_PER1_GPIO_C8,
+			PADNUM_PER1_GPIO_C9,
+			PADNUM_PER1_GPIO_C10,
+			PADNUM_PER1_GPIO_C11
+		},
+		.num_pins = 7,
+		.range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+	},
+	{
+		/* gpioe-qspi1 */
+		.pin_grp = {
+			PADNUM_PER1_GPIO_C12,
+			PADNUM_PER1_GPIO_C13,
+			PADNUM_PER1_GPIO_C14,
+			PADNUM_PER1_GPIO_C15,
+			PADNUM_PER1_GPIO_C16,
+			PADNUM_PER1_GPIO_C17,
+			PADNUM_PER1_GPIO_C18,
+			PADNUM_PER1_GPIO_C19
+		},
+		.num_pins = 8,
+		.range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+	},
+	{
+		/* gpioe-qspi2 */
+		.pin_grp = {
+			PADNUM_PER1_GPIO_C20,
+			PADNUM_PER1_GPIO_C21,
+			PADNUM_PER1_GPIO_C22,
+			PADNUM_PER1_GPIO_C23,
+			PADNUM_PER1_GPIO_C24,
+			PADNUM_PER1_GPIO_C25,
+			PADNUM_PER1_GPIO_C26,
+			PADNUM_PER1_GPIO_C27
+		},
+		.num_pins = 8,
+		.range = BIT(JHB100_PINVREF_1_8V) | BIT(JHB100_PINVREF_3_3V)
+	},
+};
+
+static const struct starfive_pinctrl_regs jhb100_per1_pinctrl_regs = {
+	.vref			= { .reg = 0x00, .pv_desc = pinvref_desc_per1,
+				    .num_pv = ARRAY_SIZE(pinvref_desc_per1) },
+	.func_sel		= { .reg = 0xbc, .width_per_pin = 2 },
+	.config			= 0x14,
+	.output			= 0xa4,
+	.output_en		= 0xac,
+	.gpio_status		= 0xb4,
+	.irq_en			= 0xc8,
+	.irq_status		= 0xd0,
+	.irq_clr		= 0xd8,
+	.irq_trigger		= 0xe0,
+	.irq_level		= 0xe8,
+	.irq_both_edge		= 0xf0,
+	.irq_edge		= 0xf8,
+};
+
+static const struct jhb100_pinctrl_func_maps jhb100_func_maps_per1[] = {
+	{ .func = "gpio",		.val = 0 },
+	{ .func = "i2c",		.val = 1 },
+	{ .func = "sfc",		.val = 1 },
+	{ .func = "sgpio",		.val = 1,
+	  .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER1_GPIO_C31) },
+	{ .func = "sgpio",		.val = 2,
+	  .max_pin = JHB100_FUNC_MAPS_MAX_PIN(PADNUM_PER1_GPIO_C35) },
+	{ .func = "spi",		.val = 1 },
+};
+
+static const struct jhb100_pinctrl_domain_info jhb100_per1_pinctrl_info = {
+	.name			= "jhb100-per1",
+	.pl_desc		= jhb100_per1_pl_desc,
+	.crl_desc		= jhb100_per1_pinctr_rldesc,
+	.regs			= &jhb100_per1_pinctrl_regs,
+	.fmaps			= jhb100_func_maps_per1,
+	.num_maps		= ARRAY_SIZE(jhb100_func_maps_per1),
+};
+
+static const struct of_device_id jhb100_per1_pinctrl_of_match[] = {
+	{
+		.compatible = "starfive,jhb100-per1-pinctrl",
+		.data = &jhb100_per1_pinctrl_info,
+	},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jhb100_per1_pinctrl_of_match);
+
+static struct platform_driver jhb100_per1_pinctrl_driver = {
+	.probe = jhb100_pinctrl_probe,
+	.driver = {
+		.name = "starfive-jhb100-per1-pinctrl",
+		.of_match_table = jhb100_per1_pinctrl_of_match,
+	},
+};
+module_platform_driver(jhb100_per1_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for StarFive JHB100 SoC Peripheral-1 domain");
+MODULE_AUTHOR("Alex Soo <[email protected]>");
+MODULE_LICENSE("GPL");
-- 
2.25.1