An unexpected IO-APIC was found....
"Jens-S. Voeckler" <[email protected]>
| Newsgroups | org.kernel.vger.linux-smp |
|---|---|
| Message-ID | <[email protected]> |
Hi,
the kernel message said to tell you - just in case I sent the whole dmesg
output for you, at the bottom. Note that, although both CPUs in the ASUS
P4S800 ACPI Rev 1004 go to work, the interrupts are not balanced:
# cat /proc/interrupts
CPU0 CPU1
0: 61728 0 IO-APIC-edge timer
1: 1186 0 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
8: 1 0 IO-APIC-edge rtc
12: 746 0 IO-APIC-edge PS/2 Mouse
14: 10095 1 IO-APIC-edge ide0
15: 4472 0 IO-APIC-edge ide1
18: 288 0 IO-APIC-level SiS SI7012
19: 3050 0 IO-APIC-level eth0
20: 0 0 IO-APIC-level acpi
23: 0 0 IO-APIC-level ehci_hcd
NMI: 0 0
LOC: 61641 61639
ERR: 0
MIS: 0
This is the output from the BIOS setting true for PnP OS - but it does not
appear to make a lot of a difference concerning that one CPU does not get
any load share of interrupts. When doing many intensive tasks in parallel,
it appears as if one CPU "saturates" before the other one is doing things.
# cat boot.log
Linux version 2.4.23 ([email protected]) (gcc version 3.3.2) #1 SMP Thu Dec 4 18:45:42 CST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fffc000 (usable)
BIOS-e820: 000000003fffc000 - 000000003ffff000 (ACPI data)
BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
ACPI: have wakeup address 0xc0002000
On node 0 totalpages: 262140
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32764 pages.
ACPI: RSDP (v000 ASUS ) @ 0x000f5850
ACPI: RSDT (v001 ASUS P4S800 0x42302e31 MSFT 0x31313031) @ 0x3fffc000
ACPI: FADT (v001 ASUS P4S800 0x42302e31 MSFT 0x31313031) @ 0x3fffc0c0
ACPI: BOOT (v001 ASUS P4S800 0x42302e31 MSFT 0x31313031) @ 0x3fffc030
ACPI: MADT (v001 ASUS P4S800 0x42302e31 MSFT 0x31313031) @ 0x3fffc058
ACPI: DSDT (v001 ASUS P4S800 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 Pentium 4(tm) XEON(tm) APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 Pentium 4(tm) XEON(tm) APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] polarity[0x1] trigger[0x1] lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 128, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x1])
ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x14] polarity[0x3] trigger[0x3])
ACPI BALANCE SET
Using ACPI (MADT) for SMP configuration information
Kernel command line: ro root=/dev/hda3 hdc=ide-scsi vga=791 apm=off single
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 2600.129 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 5190.45 BogoMIPS
Memory: 1032836k/1048560k available (1897k kernel code, 15336k reserved, 607k data, 132k init, 131056k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
per-CPU timeslice cutoff: 1462.82 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5190.45 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU1: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
Total of 2 processors activated (10380.90 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-9, 2-16, 2-17, 2-18, 2-19, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2600.2865 MHz.
..... host bus clock speed is 200.0217 MHz.
cpu: 0, clocks: 2000217, slice: 666739
CPU0<T0:2000208,T1:1333456,D:13,S:666739,C:2000217>
cpu: 1, clocks: 2000217, slice: 666739
CPU1<T0:2000208,T1:666720,D:10,S:666739,C:2000217>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
ACPI: Subsystem revision 20031002
PCI: PCI BIOS revision 2.10 entry at 0xf1100, last bus=1
PCI: Using configuration type 1
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xa9 -> IRQ 20 Mode:1 Active:1)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
PCI: Probing PCI hardware
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb1 -> IRQ 16 Mode:1 Active:1)
00:00:02[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb9 -> IRQ 17 Mode:1 Active:1)
00:00:02[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xc1 -> IRQ 18 Mode:1 Active:1)
00:00:02[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc9 -> IRQ 19 Mode:1 Active:1)
00:00:02[D] -> 2-19 -> IRQ 19
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd1 -> IRQ 21 Mode:1 Active:1)
00:00:03[B] -> 2-21 -> IRQ 21
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd9 -> IRQ 22 Mode:1 Active:1)
00:00:03[C] -> 2-22 -> IRQ 22
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xe1 -> IRQ 23 Mode:1 Active:1)
00:00:03[D] -> 2-23 -> IRQ 23
Pin 2-19 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178080
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0080
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to [email protected]
.... register #02: 02000000
....... : arbitration: 02
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 0 0 0 0 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 000 00 1 0 0 0 0 0 0 00
0a 003 03 0 0 0 0 0 1 1 71
0b 003 03 0 0 0 0 0 1 1 79
0c 003 03 0 0 0 0 0 1 1 81
0d 003 03 0 0 0 0 0 1 1 89
0e 003 03 0 0 0 0 0 1 1 91
0f 003 03 0 0 0 0 0 1 1 99
10 003 03 1 1 0 1 0 1 1 B1
11 003 03 1 1 0 1 0 1 1 B9
12 003 03 1 1 0 1 0 1 1 C1
13 003 03 1 1 0 1 0 1 1 C9
14 003 03 0 1 0 1 0 1 1 A9
15 003 03 1 1 0 1 0 1 1 D1
16 003 03 1 1 0 1 0 1 1 D9
17 003 03 1 1 0 1 0 1 1 E1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:20
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
vesafb: framebuffer at 0xf0000000, mapped to 0xf885e000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:5490
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: Detected SiS 648 chipset
agpgart: AGP aperture is 256M @ 0xd0000000
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xa400-0xa407, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xa408-0xa40f, BIOS settings: hdc:DMA, hdd:pio
hda: WDC WD400JB-00ENA0, ATA DISK drive
hdb: WDC WD2000JB-32FUA0, ATA DISK drive
blk: queue c03d3b40, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03d3c88, I/O limit 4095Mb (mask 0xffffffff)
hdc: LITE-ON LTR-52327S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78165360 sectors (40021 MB) w/8192KiB Cache, CHS=4865/255/63, UDMA(100)
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 390721968 sectors (200050 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100)
Partition check:
hda: hda1 hda2 hda3
hdb: hdb1
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling device 00:03.3 (0004 -> 0006)
ehci_hcd 00:03.3: Silicon Integrated Systems [SiS] USB 2.0 Controller
ehci_hcd 00:03.3: irq 23, pci mem f8806000
usb.c: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 00:03.3
ehci_hcd 00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
hub.c: USB hub found
hub.c: 6 ports detected
host/usb-uhci.c: $Revision: 1.275 $ time 18:46:52 Dec 4 2003
host/usb-uhci.c: High bandwidth mode enabled
host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 132k freed
Adding Swap: 2096472k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide0(3,65)) ...
for (ide0(3,65))
ide0(3,65):Using r5 hash to sort names
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LITE-ON Model: LTR-52327S Rev: QS0B
Type: CD-ROM ANSI SCSI revision: 02
hdc: DMA disabled
--
Ciao,
Dipl.-Ing. Jens-S. Vöckler voeckler at cs dot uchicago dot edu
University of Chicago; Research Institutes Building #402;
5640 South Ellis Avenue; Chicago, IL 60637-1433; USA; +1 773 834 6693
You can rely on NFS for only one thing - don't!