Re: SMP Woes

Howdy,

I figured out the MPS 1.4 issue, it was enabled in my BIOS. I just
downloaded 2.6.5 and installed it. Everything works except the video mode. I
have "vga=791" in lilo.conf, which has worked on every kernel I've ever
built. 2.6.5 just ignores it. Ireadup a little on the vesafb, it has a lot
more stuff about configuring then I've seen before. In a bit I'm going to
reboot with "vga=ask" to see if I can use something different.

Bobby

----- Original Message ----- 
From: "Vladimir G. Ivanovic" <[email protected]>
To: "Bobby Hitt" <[email protected]>
Cc: <[email protected]>
Sent: Thursday, April 22, 2004 1:21 PM
Subject: Re: SMP Woes


> I have an ASUS CUV4X-DLS dual-processor motherboard that I've been
> running for three years (?).
>
> I use grub; here is my grub.conf file:
>
>    timeout=10
>    splashimage=(hd0,0)/grub/splash.xpm.gz
>    default=0
>
>    title Fedora Core (2.4.22-1.2179.nptlsmp)
>            root (hd0,0)
>            kernel /vmlinuz-2.4.22-1.2179.nptlsmp root=/dev/sda4
hdb=ide-scsi ide2=0x9400,0x9002 ide3=0x8800,0x8402
>            initrd /initrd-2.4.22-1.2179.nptlsmp.img
>
>    title Fedora Core (2.4.22-1.2174.nptlsmp)
>            root (hd0,0)
>            kernel /vmlinuz-2.4.22-1.2174.nptlsmp root=/dev/sda4
hdb=ide-scsi ide2=0x9400,0x9002 ide3=0x8800,0x8402
>            initrd /initrd-2.4.22-1.2174.nptlsmp.img
>
>    title Memtest86 v3.1
>            kernel /memtest86-3.1
>
> But to get Linux SMP to run, I had to turn off MPS 1.4 support in the
> BIOS. I also turn off automatic IDE detection, but then enable the
> Primary IDE channel. (I have an 133 MHz IDE controller hooked up to a
> 200 GB drive.)
>
> Let me know if you want more details about my setup.
>
> --- Vladimir
>
> ------------------------------------------------------------------------
> Vladimir G. Ivanovic                        http://leonora.org/~vladimir
> 2770 Cowper St.                                         [email protected]
> Palo Alto, CA 94306-2447                                 +1 650 678 8014
> ------------------------------------------------------------------------
>
> >>>>> "bh" == Bobby Hitt <[email protected]> writes:
>
>     bh> Hello,
>     bh>
>     bh> I recently posted this message to the linux-kernel list:
>     bh> ------
>     bh> I have an ASUS CUV4XD dual CPU mobo that I've been using with
Window 2000
>     bh> Professional for the last two years. It worked fine, W2K used both
CPUs with
>     bh> no problems whatsoever. I recently upgraded my W2K system, and
decided to
>     bh> use the ASUS board in a system I was building to use as a Linux
gateway. The
>     bh> problem I'm having is the system refuses to boot when I created a
kernel
>     bh> with SMP support. If I turn off SMP and rebuild the kernel, boots
fine. I
>     bh> have two other SMP systems, very old mother boards, 5+ years old.
They both
>     bh> run Linux fine with SMP. I even took the source tree from a
working system,
>     bh> built a new kernel, locks up on bootup. The last message displayed
:
>     bh>
>     bh> Total of 2 processors activated ( 3186.68 BogoMIPS)
>     bh> Enabling IO-APIC IRQs
>     bh> Setting 2 in the phys_id_present_map
>     bh> .. changing IO-APIC physical APIC ID to 2 ... ok.
>     bh>
>     bh> I contacted Alan Cox about this, he said he was working on his MBa
and
>     bh> hadn't been involved with kernel development for a while. He
suggest adding:
>     bh>
>     bh> append="noapic pci=usepirqmask"
>     bh>
>     bh> to the lilo.conf file, which I did. No change.
>     bh>
>     bh> Any body have similar problems or suggestions?
>     bh> ------
>     bh>
>     bh> This was for kernel 2.4.23.
>     bh>
>     bh> I've since figured out that problem. I found that the BIOS had an
option
>     bh> "MPS 1/4 Support" which was checked. Turned that off, and now the
system
>     bh> boots fine, but now have a new problem with my RAID configuration.
When
>     bh> "raidstart /dev/md0" runs, it gives this error:
>     bh>
>     bh> cannot determine md version: 6
>     bh>
>     bh> The only thing I've done is to enable smp support in the kernel,
which
>     bh> brings up another issue. I had just installed the source tree for
2.4.26.
>     bh> smp support was already checked, so all I did was to enable raid,
reiserfs
>     bh> support, etc. I didn't turn on anything un-necessary. With
"vga=791" set in
>     bh> the lilo.conf file, on reboot now all I get is a black screen and
system
>     bh> lockup. When I went back to turn off smp, now the build fails with
lots of
>     bh> "num_cpus" (or close to that) appear everywhere. The only way I
can now
>     bh> build a new kernel is to save my .config file, wipe the directory,
>     bh> re-install the source tree, copy my .config file back and rebuild.
With
>     bh> regard to the display issue, I'll disable the display for now. The
raid
>     bh> issue is the main thing.
>     bh>
>     bh> TIA,
>     bh>
>     bh> Bobby
>     bh>
>     bh> -
>     bh> To unsubscribe from this list: send the line "unsubscribe
linux-smp" in
>     bh> the body of a message to [email protected]
>     bh> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>     bh>
>