Re: Unable to Load Included Impress Templates in ooo-build 3.2.1.4

On 06/22/2010 10:15 PM, [email protected] wrote:
> On 06/22/2010 09:50 PM, Christoph Willing wrote:
>>
>> On 23/06/2010, at 1:24 PM, <[email protected]> <[email protected] 
>>  > wrote:
>>
>>> On 06/22/2010 07:07 PM, Christoph Willing wrote:
>>>>
>>>> On 23/06/2010, at 8:34 AM, <[email protected]> <[email protected]
>>>>> wrote:
>>>>
>>>>> Hi List,
>>>>>
>>>>> I have successfully built ooo-build 3.2.1.4 for Slackware64 13.1.
>>>>> Now I
>>>>> am having problems using the included Impress background templates.
>>>>
>>>>
>>>> I have also built 3.2.1.4 for Slackware64-13.1 but I can't reproduce
>>>> that problem. Templates & backgrounds load without any trouble.
>>>>
>>>> Perhaps you could check our binary at:
>>>>     http://www.vislab.uq.edu.au/slackware64/13.1/openoffice-3.2.1.4-x86_64-1_uqv.txz
>>>>
>>>> and if it works as expected (which it should) then we can investigate
>>>> whether some difference in building technique is causing the problem.
>>>>
>>>>
>>>> chris
>>>
>>> Thanks for responding, Chris.  Sure enough I do not have the same
>>> problems using your OOo package.
>>>
>>> Yours is built with an older icu4c.  That is the first difference I
>>> noticed.  I had to replace my icu4c package with yours.  I do not
>>> believe that is the cause of my issue, as I had the same problems with
>>> Impress when I built ooo-build 3.2.0.x for Slackware 13.0.  That was
>>> built against icu4c 4.2.1 (the same version you used).
>>>
>>> Here is my configure command line:
>>>
>>> CFLAGS="-O2 -fPIC" \
>>> CXXFLAGS="-O2 -fPIC" \
>>> ./configure \
>>>   --prefix=/usr \
>>>   --libdir=/usr/lib64 \
>>>   --sysconfdir=/etc \
>>>   --localstatedir=/var/lib \
>>>   --mandir=/usr/man \
>>>   --docdir=/usr/doc/openoffice-3.2.1.4 \
>>>   --build=x86_64-slackware-linux \
>>>   --with-distro=Slackware \
>>>   --with-ant-home=/usr/share/ant \
>>>   --with-lang="" \
>>>   --disable-odk \
>>>   --disable-pam \
>>>   --disable-pam-link \
>>>   --disable-post-install-scripts \
>>>   --enable-access \
>>>   --enable-cairo \
>>>   --disable-kde \
>>>   --disable-kde4 \
>>>   --enable-gtk \
>>>   --with-system-cairo \
>>>   --with-system-neon \
>>>   --with-system-icu \
>>>   --with-system-expat \
>>>   --with-system-boost \
>>>   --with-system-mozilla=seamonkey \
>>>   --disable-mono \
>>>   --with-docdir=/usr/doc/openoffice-3.2.1.4 \
>>>   --with-gcc-speedup=ccache \
>>>   --with-openclipart=/usr/share/openclipart \
>>>   --enable-pdfimport
>>>
>>> I've had to apply the patch included in this post:
>>> http://lists.freedesktop.org/archives/ooo-build/2010-January/000473.html
>>>
>>> That thread was started by me, as well.  No matter what I tried to use
>>> for --with-lang the build would fail.  I tried setting it to "",
>>> "en-US", and "en-US fr" without luck.  So I dug up that patch again  
>>> and
>>> configured with --with-lang="".
>>
>>
>> I haven't used any --with-lang at all in mine. I wonder if adding the  
>> patch suggested above which enables you to use it causes your problem?  
>> The patch name (sdext-presenter-makefile.diff) indicates that it plays  
>> around with the presenter makefile and maybe it has some bad side  
>> effect.
> 
> About 1.5 hours ago I started a build sans the above mentioned patch and
> leaving --with-lang out completely.  Because, as you say, building
> OpenOffice takes a fair bit of time, so I might as well try something as
> soon as possible.  I *think* I tried this approach already prior to
> resulting to trying the above patch, but I could be wrong.  I'll find
> out in a few hours whether or not it will build.
> 
>>
>> Since I don't set any --with-lang option, nor explicitly apply the  
>> above patch, I see a "fail" during compilation, same as already  
>> mentioned in http://lists.freedesktop.org/archives/ooo-build/2010-March/000741.html 
>> .
>>
>>
>>> Is there any chance you can share your build process, or perhaps the
>>> SlackBuild you used?
>>
>> Its included in the binary package in /usr/src/slackbuilds/ 
>> openoffice-3.2.1.4/Slack.build. Sorry its a bit messy - I often try  
>> new things with the builds but since the turn around time compiling/ 
>> testing for ooo is quite long, I tend to leave old things lying around  
>> in there much longer than I normally would, in case I need to revert  
>> to a previous incantation. The Slack.build uses some global helper  
>> functions of my own that are not included in that directory but their  
>> usage is pretty transparent.
>>
> 
> Thanks.  I guess I didn't examine the install log from your package
> closely enough to notice that.  You and I use a few different options,
> but it is unclear to me if any of them would have an impact.  I also see
> you and I came up similar fixes for the OpenOffice menus in Xfce missing
> icons.
> 
> Unfortunately I'll be away for about a week, so my time to experiment is
> limited for now.
> 
> -Mike
> 

When I got back in town last night I rebuilt ooo-build 3.2.1.4.  This
time I did not use any --with-lang configure option or the patch from
http://lists.freedesktop.org/archives/ooo-build/2010-January/000473.html.
The build failed until I configured without using --enable-pdfimport.
Obviously the PDF Import extension was not built.  Neither was the
Presentation Minimizer extension.  However, I am now able to use
templates in Impress.

-Mike