Re: Re: proxy arp problems

1.2 didn't resolve the problem, still no proxy arp.  It seems my
upstream isn't accepting the proxy arp. I didn't have time to wait for
the arp to time out or wait on a support ticket to get them to clear
(not sure if they would), so I am spoofing the mac address on the WAN
interface of the previous server who had the IP addresses (it's now
behind my m0n0wall).

This isn't ideal, I don't like spoofing it, but it was the only thing
that I found would work and allow me to get the firewall up and
running.

Thanks for all of the input and suggestions.
Charles

On Fri, Dec 11, 2009 at 10:35 AM, Charles Goldsmith
<[email protected]> wrote:
> Ok, thanks.  I'll downgrade to 1.2 this weekend hopefully and test
> from there and post my results.
>
> Charles
>
> On Fri, Dec 11, 2009 at 5:08 AM, Ulrik Lunddahl (PROconsult)
> <[email protected]> wrote:
>> I'm using Proxy ARP in a production environment, for two subnets from my ISP, it's running fine, but with version 1.21
>>
>> I'm about to upgrade to version 1.3, but it will be in the next few weeks. When I have upgraded, I will post here.
>>
>>
>> Med venlig hilsen, Best regards
>> Ulrik Lunddahl
>>
>> Sales Manager - Salgschef
>> PROconsult Data A/S - Rugårdsvej 15 - 5000  Odense C
>> Tel: +45 63113333 - Tel dir: +45 63113341 - Mobil: +45 26363341 - Fax: +45 63113344
>> E-mail: [email protected] - Web site: www.proconsult.dk
>>
>>
>>
>> VSP - Infrastructure Optimization Solutions
>> VSP - Business Continuity
>> VTSP - VMware Infrastructure Virtualization
>> vExpert - Nominated for and Awarded the vExpert award in February 2009
>>
>>
>>
>> -----Oprindelig meddelelse-----
>> Fra: Charles Goldsmith [mailto:[email protected]]
>> Sendt: 10. december 2009 23:14
>> Til: [email protected]
>> Emne: [m0n0wall] Re: proxy arp problems
>>
>> Is anyone using Proxy Arp in a production environment on 1.3?  Also,
>> if so, are you using it with Server NATs or 1:1 NATs?
>>
>> Thanks
>> Charles
>>
>> On Tue, Dec 8, 2009 at 10:47 PM, Charles Goldsmith <[email protected]> wrote:
>>> I've been a user of m0n0 for several years, and am trying to put a new
>>> install in at a colo.  Soekris 5501 with 1.3 new install on a flash
>>> card.
>>>
>>> No problems with the basic nat/fw setup.  But when I setup a few
>>> server NATs and proxy arp, the proxy arp doesn't seem to be working.
>>>
>>> I have a /29 in a vlan, so the ISP isn't routing it.  If I unplug my
>>> WAN port on the firewall and plug into my linux laptop, I can alias in
>>> all of the IP's and can ping them from remote.  The m0n0 doesn't seem
>>> to proxy arp my secondary IP's or the server nat's don't work, not
>>> totally sure, but it seems to be proxy arp.  I enabled ICMP to all
>>> ip's and can ping the WAN address, but I cannot ping any of the other
>>> IP's.
>>>
>>> Is anyone using server nats and proxy arp with 1.3 sucessfully?  I
>>> might be able to get my ISP to route the IPs for me, but I'd rather
>>> not bother them with this.
>>>
>>> Any help would be appreciated.
>>> Charles
>>>
>>
>> ---------------------------------------------------------------------
>> To unsubscribe, e-mail: [email protected]
>> For additional commands, e-mail: [email protected]
>>
>>
>> ---------------------------------------------------------------------
>> To unsubscribe, e-mail: [email protected]
>> For additional commands, e-mail: [email protected]
>>
>>
>