RE: Install Monowall on USB Thumb Drive?

Yes,

I did run it as admin. As I am login as admin. It worked well with regular
harddrive.

Here is the error messages:
physdiskwrite v0.5.2 by Manuel Kasper <[email protected]>

Searching for physical drives...

Information for \\.\PhysicalDrive0:
   Windows:       cyl: 19457
                  tpc: 255
                  spt: 63
   C/H/S:         16383/16/63
   Model:         MAXTOR STM3160215AS
   Serial number:             5RA7RB12
   Firmware rev.: 4.AAB

Information for \\.\PhysicalDrive1:
   Windows:       cyl: 41345
                  tpc: 240
                  spt: 63
   C/H/S:         16383/16/63
   Model:         WDC WD3200AAKS-00L6A0
   Serial number:      WD-WMAV23715016
   Firmware rev.: 01.03E01

Information for \\.\PhysicalDrive2:
   Windows:       cyl: 30401
                  tpc: 255
                  spt: 63

Information for \\.\PhysicalDrive3:
   Windows:       cyl: 3
                  tpc: 255
                  spt: 63

Information for \\.\PhysicalDrive4:
   Windows:       cyl: 14593
                  tpc: 255
                  spt: 63

Which disk do you want to write? (0..4) 3
About to overwrite the contents of disk 3 with new data. Proceed? (y/n) y
Found signed compressed image file
Write error after 0 bytes (8192).

Thank you
Rendra

-----Original Message-----
From: Michel Servaes [mailto:[email protected]] 
Sent: Friday, September 24, 2010 4:09 PM
To: [email protected]
Cc: 'Heinz Teichmann'; [email protected]
Subject: Re: [m0n0wall] Install Monowall on USB Thumb Drive?

  Make sure to run physdiskwrite as "administrator" (even if you are admin
!), winvista or win7 !

Op 24/09/2010 10:37, GD Incorporation schreef:
>
> Is the CF image the same as the Generic PC image? I Use only 32MB Old 
> USB Drive.
>
> Can you tell me what GUI tool you are using to copy the image to the 
> USB? I used the physdiskwrite.exe tool and it always returns error.
>
> Thanks
> Rendra
>
> -----Original Message-----
> From: Heinz Teichmann [mailto:[email protected]]
> Sent: Friday, September 24, 2010 2:32 PM
> To: Gold Dragon
> Subject: FW: [m0n0wall] Install Monowall on USB Thumb Drive?
>
>
>
>
> I did it with the normal CF image. I think there is a limitation 
> regarding the size. First time I tried it with a 100 GB USB HDD, it 
> didn't load the image up and came up with a fault. Second time I used 
> a 1 GB USB Stick and that worked well. I used that GUI tool to install 
> the image and that doesn't return any errors, so use the CLI if you 
> want to make sure that it had been copied correctly.
> I dumped Monowall again because of the VPN issues with Dynamic DNS. I 
> need a stable VPN with two AVM Fritz boxes behind dyndns and that is 
> not achievable with Monowall. Unfortunately. Because I think it's great
otherwise.
>
> HT
>
> -----Original Message-----
> From: David Burgess [mailto:[email protected]]
> Sent: Friday, 24 September 2010 1:56 PM
> Cc: [email protected]
> Subject: Re: [m0n0wall] Install Monowall on USB Thumb Drive?
>
> On Thu, Sep 23, 2010 at 11:50 PM, GD Incorporation 
> <[email protected]>  wrote:
>> Can anyone tell me how to install m0n0wall 1.32 on USB thumb drive?
> Have you tried just following the instructions for CF installation?
> That's where I would start, then make sure your BIOS is set to boot 
> from the USB device. I did a FreeNAS install on USB once, and I think 
> that's how I did it.
>
> db
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [email protected]
> For additional commands, e-mail: [email protected]
>
>
>
> www.thewest.com.au
>
> ----------------------------------------------------------------------
> ------
> --------
> West Australian Newspapers Group
> ----------------------------------------------------------------------
> ------
> --------
> Privacy and Confidentiality Notice
>
> The information contained herein and any attachments are intended 
> solely for the named recipients. It may contain privileged confidential
information.
> If you are not an intended recipient, please delete the message and 
> any attachments then notify the sender. Any use or disclosure of the 
> contents of either is unauthorised and may be unlawful. Any liability 
> for viruses is excluded to the fullest extent permitted by law.
>
> Advertising Terms&  Conditions
> Please refer to the current rate card for advertising terms and
conditions.
> The rate card is available on request or via 
> www.thewest.com.au/ratecard
>
> Unsubscribe
> If you do not wish to receive emails such as this in future please 
> reply to it with "unsubscribe" in the subject line.
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [email protected]
> For additional commands, e-mail: [email protected]
>