Re: websphere dev studio 5.1
Edmund Reinhardt <[email protected]> Fri, 26 Sep 2003 15:30:29 -0400
| Newsgroups | gmane.comp.systems.as400.code |
|---|---|
| Message-ID | <[email protected]> |
>> I was just passing on the article to show >> that it is still possible to just use CODE/400 >> and not the rest of the stuff you get in WDSC. > Yup - I understand. I just wanted to relate that if one can't load WDSCi, > one can't use Code in WDSCi. Buck are you saying you can't install WDSCi or you can't run it once it is installed? I would not attempt to run WDSCi on your hardware but once everything is installed, you will be running the same CODE/400 with some bug refreshes and minor enhancements. (I did finally get around to adding the Split Constant function in CODE Designer after all these years ;-) But you will have to wait for the next service pack WDSc 5.1 to get it.) --------------------------------------------------------------------------------------------- Edmund Reinhardt, AS/400 AD Tools, [email protected] Dept 607, IBM Canada Lab TL 969-4392 Phone 905-413-4392 "Buck" <buck.calabro@comms To: code400-l-Zwy7GipZuJhWk0Htik3J/[email protected] oft.net> cc: Sent by: Subject: Re: websphere dev studio 5.1 code400-l-bounces@m idrange.com 26/09/2003 03:09 PM Please respond to CODE/400 Discussion & Support > I was just passing on the article to show > that it is still possible to just use CODE/400 > and not the rest of the stuff you get in WDSC. Yup - I understand. I just wanted to relate that if one can't load WDSCi, one can't use Code in WDSCi. > "PII" - Is that right or a typo? Man, that is an OLD processor. That's right. Pentuim II, 450 MHz. And it runs WDT 5.1 Code/400 very snappily. Considering the anemic state of the economy, the company is rather unwilling to spend $1000+ USD (PC + XP license fee) to enable me to use a fraction of the capability (we're green screen only) of a slower running, less functional (jLpex is still behind Code), web-centric development tool like WDSCi. And I honestly can't say I can blame the boss this time. I'm already using PC based Code/400, so I'm already pretty productive - and we don't target V5R2 so I don't even notice the fact that WDT 5.1 Code chokes on V5R2 BIFs. > The current version of CODE/400 that comes with WDSC 5.0 > fully supports all the new RPG IV stuff in V5R2. Very nice. Thanks for that! --buck _______________________________________________ This is the CODE/400 Discussion & Support (CODE400-L) mailing list To post a message email: CODE400-L-Zwy7GipZuJhWk0Htik3J/[email protected] To subscribe, unsubscribe, or change list options, visit: http://lists.midrange.com/mailman/listinfo/code400-l or email: CODE400-L-request-Zwy7GipZuJhWk0Htik3J/[email protected] Before posting, please take a moment to review the archives at http://archive.midrange.com/code400-l. NOTE: WDSc for iSeries disucssion has it's own mailing list. Information can be found at http://lists.midrange.com/cgi-bin/listinfo/wdsc-l _______________________________________________ This is the CODE/400 Discussion & Support (CODE400-L) mailing list To post a message email: CODE400-L-Zwy7GipZuJhWk0Htik3J/[email protected] To subscribe, unsubscribe, or change list options, visit: http://lists.midrange.com/mailman/listinfo/code400-l or email: CODE400-L-request-Zwy7GipZuJhWk0Htik3J/[email protected] Before posting, please take a moment to review the archives at http://archive.midrange.com/code400-l. NOTE: WDSc for iSeries disucssion has it's own mailing list. Information can be found at http://lists.midrange.com/cgi-bin/listinfo/wdsc-l