Always the same problem with Voip and Hylafax

Giulio Nuti <[email protected]>
Newsgroups gmane.comp.telephony.fax.hylafax.user
Message-ID <[email protected]> 
Hi,
I ave a Voip line with Aethra SV1204... ISDN PBX - BOSCH (some ISDN
extensions, some PSTN) ... Hylafax to send fax.

With direct ISDN external lines from internal PSTN sending faxes was Ok.
If the receiving fax is a "software fax server" (hylafax maybe) I can
send/ receive data, but the document result in a micro image on a corner
on an A4 paper..
Sometime the connection hangs up.

There is some config in the modem I can use to correct these issues?


 I hope I won't bother you too much...

----------------
| config.ttyS  |
----------------

# Configuration for a Rockwell RC288DPi-based Class 1 modem.
#    Hayes Optima 28800         firmware rev ???
#    Microcom DeskPorte 28.8S   firmware rev V1.100K-V34_DS
#    PPI PM288FXMT              firmware rev 1.57
#
# Note that the modem does not lock the line rate for fax
# receive (at least not the PM288FXMT); but not sure whether
# current flow control settings are maintained or if it
# switches to XON/XOFF (testing host was too fast to see).
#
#
CountryCode:            39
AreaCode:               6
FAXNumber:              0
LongDistancePrefix:     0
InternationalPrefix:    0
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           50
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use this to supply a hint
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd: !RC288DPi
ModemRevQueryCmd: ATI3 # product information
#
ModemDialCmd: ATX3DT%s # T for tone dialing
---------------------------------------------------------
---------------------------------------------------------



SEND.log
------------


feb 01 15:58:20.84: [30871]: HylaFAX (tm) Version 6.0.6
feb 01 15:58:20.84: [30871]: SEND FAX: JOB 105 DEST XXXXXXXXXXXXX COMMID
000000321 DEVICE '/dev/ttyS0' FROM 'giulio <[email protected]>'
USER giulio
feb 01 15:58:20.84: [30871]: <-- [12:AT+FCLASS=1\r]
feb 01 15:58:20.85: [30871]: --> [2:OK]
feb 01 15:58:20.86: [30871]: DIAL XXXXXXXXXXX
feb 01 15:58:20.86: [30871]: <-- [18:ATX3DTXXXXXXXX\r]
feb 01 15:58:36.15: [30871]: --> [7:CONNECT]
feb 01 15:58:36.27: [30871]: --> [5:ERROR]
feb 01 15:58:36.27: [30871]: MODEM Command error
feb 01 15:58:36.27: [30871]: FCS error		<<<<<==<<<<<==<<<<<==
feb 01 15:58:36.27: [30871]: <-- [10:AT+FRS=21\r]
feb 01 15:58:36.52: [30871]: --> [2:OK]
feb 01 15:58:36.52: [30871]: <-- [9:AT+FTH=3\r]
feb 01 15:58:36.55: [30871]: --> [7:CONNECT]
feb 01 15:58:36.55: [30871]: <-- data [3]
feb 01 15:58:36.55: [30871]: <-- data [2]
feb 01 15:58:37.85: [30871]: --> [2:OK]
feb 01 15:58:37.85: [30871]: SEND send CRP (command repeat)
feb 01 15:58:37.85: [30871]: <-- [9:AT+FRH=3\r]
feb 01 15:58:41.42: [30871]: --> [7:CONNECT]
feb 01 15:58:42.90: [30871]: --> [2:OK]
feb 01 15:58:42.90: [30871]: REMOTE CSI "xxxxxxxx"
feb 01 15:58:42.90: [30871]: <-- [9:AT+FRH=3\r]
feb 01 15:58:42.91: [30871]: --> [7:CONNECT]
feb 01 15:58:43.19: [30871]: --> [2:OK]
feb 01 15:58:43.19: [30871]: REMOTE best rate 9600 bit/s
feb 01 15:58:43.19: [30871]: REMOTE max A3 page width (303 mm)
feb 01 15:58:43.19: [30871]: REMOTE max unlimited page length
feb 01 15:58:43.19: [30871]: REMOTE best vres 7.7 line/mm
feb 01 15:58:43.19: [30871]: REMOTE format support: MH, MR
feb 01 15:58:43.19: [30871]: REMOTE best 0 ms/scanline
feb 01 15:58:43.19: [30871]: USE 9600 bit/s
feb 01 15:58:43.19: [30871]: SEND file "docq/doc107.ps;41"
feb 01 15:58:43.19: [30871]: USE A4 page width (215 mm)
feb 01 15:58:43.19: [30871]: USE unlimited page length
feb 01 15:58:43.19: [30871]: USE 7.7 line/mm
feb 01 15:58:43.19: [30871]: USE 2-D MR
feb 01 15:58:43.19: [30871]: USE 0 ms/scanline
feb 01 15:58:43.19: [30871]: SEND training at v.29 9600 bit/s
feb 01 15:58:43.19: [30871]: <-- [9:AT+FRS=7\r]
feb 01 15:58:43.30: [30871]: --> [2:OK]
feb 01 15:58:43.30: [30871]: <-- [9:AT+FTH=3\r]
feb 01 15:58:43.33: [30871]: --> [7:CONNECT]
feb 01 15:58:43.33: [30871]: <-- data [23]
feb 01 15:58:43.33: [30871]: <-- data [2]
feb 01 15:58:45.12: [30871]: --> [7:CONNECT]
feb 01 15:58:45.12: [30871]: <-- data [6]
feb 01 15:58:45.12: [30871]: <-- data [2]
feb 01 15:58:45.54: [30871]: --> [2:OK]
feb 01 15:58:45.54: [30871]: <-- [9:AT+FTS=7\r]
feb 01 15:58:45.63: [30871]: --> [2:OK]
feb 01 15:58:45.63: [30871]: <-- [10:AT+FTM=96\r]
feb 01 15:58:45.66: [30871]: --> [7:CONNECT]
feb 01 15:58:45.66: [30871]: <-- data [1024]
feb 01 15:58:45.66: [30871]: <-- data [776]
feb 01 15:58:45.66: [30871]: <-- data [2]
feb 01 15:58:47.62: [30871]: --> [2:OK]
feb 01 15:58:47.62: [30871]: <-- [9:AT+FRH=3\r]
feb 01 15:58:49.10: [30871]: --> [7:CONNECT]
feb 01 15:58:49.99: [30871]: --> [2:OK]
feb 01 15:58:49.99: [30871]: TRAINING succeeded
feb 01 15:58:49.99: [30871]: <-- [9:AT+FRS=7\r]
feb 01 15:58:50.10: [30871]: --> [2:OK]
feb 01 15:58:50.10: [30871]: <-- [10:AT+FTM=96\r]
feb 01 15:58:50.14: [30871]: --> [7:CONNECT]
feb 01 15:58:50.14: [30871]: SEND begin page
feb 01 15:58:50.14: [30871]: <-- data [1027]
feb 01 15:58:50.14: [30871]: <-- data [1024]
feb 01 15:58:50.14: [30871]: <-- data [1024]
feb 01 15:58:50.14: [30871]: <-- data [1024]
feb 01 15:58:50.14: [30871]: <-- data [1024]
feb 01 15:58:51.46: [30871]: <-- data [1024]
feb 01 15:58:52.36: [30871]: <-- data [1043]
feb 01 15:58:53.25: [30871]: <-- data [1043]
feb 01 15:58:54.14: [30871]: <-- data [1055]
feb 01 15:58:55.04: [30871]: <-- data [262]
feb 01 15:58:55.04: [30871]: SENT 9472 bytes of data
feb 01 15:58:55.04: [30871]: SEND 2D RTC
feb 01 15:58:55.04: [30871]: <-- data [30]
feb 01 15:58:55.04: [30871]: <-- data [2]
feb 01 15:58:55.04: [30871]: SEND end page
feb 01 15:58:58.51: [30871]: --> [2:OK]
feb 01 15:58:58.51: [30871]: <-- [9:AT+FTS=9\r]
feb 01 15:58:58.62: [30871]: --> [2:OK]
feb 01 15:58:58.62: [30871]: SEND send EOP (no more pages or documents)
feb 01 15:58:58.62: [30871]: <-- [9:AT+FTH=3\r]
feb 01 15:58:58.65: [30871]: --> [7:CONNECT]
feb 01 15:58:58.65: [30871]: <-- data [3]
feb 01 15:58:58.65: [30871]: <-- data [2]
feb 01 15:58:59.95: [30871]: --> [2:OK]
feb 01 15:58:59.95: [30871]: <-- [9:AT+FRH=3\r]
feb 01 15:59:01.35: [30871]: --> [7:CONNECT]
feb 01 15:59:02.30: [30871]: --> [2:OK]
feb 01 15:59:02.30: [30871]: SEND recv MCF (message confirmation)
feb 01 15:59:02.30: [30871]: SEND FAX (000000321): FROM
[email protected] TO 0xxxxxxx (page 1 of 1[1,1,0,0]  sent in 0:00:19)
feb 01 15:59:02.30: [30871]: <-- [9:AT+FRS=7\r]
feb 01 15:59:02.42: [30871]: --> [2:OK]
feb 01 15:59:02.42: [30871]: SEND FAX (000000321): FROM
[email protected] TO 0xxxxxxxx (docq/doc107.ps;41 sent in 0:00:19)
feb 01 15:59:02.42: [30871]: <-- [9:AT+FTH=3\r]
feb 01 15:59:02.45: [30871]: --> [7:CONNECT]
feb 01 15:59:02.45: [30871]: <-- data [3]
feb 01 15:59:02.45: [30871]: <-- data [2]
feb 01 15:59:03.75: [30871]: --> [2:OK]
feb 01 15:59:04.75: [30871]: <-- [5:ATH0\r]
feb 01 15:59:05.66: [30871]: --> [2:OK]
feb 01 15:59:05.66: [30871]: SESSION END
-----------------------------------------------------------------
-----------------------------------------------------------------






-- 
Arch. Giulio Nuti


Questo messaggio di posta elettronica contiene informazioni di carattere
confidenziale rivolte esclusivamente al destinatario sopra indicato.
E' vietato l'uso, la diffusione, distribuzione o riproduzione da parte
di ogni altra personain accordo alle direttive del DL 196/03
Nel caso aveste ricevuto questo messaggio di posta elettronica per
errore, siete pregati di segnalarlo immediatamente al mittente e
distruggere quanto ricevuto (compresi file allegati) senza farne copia.
Qualsivoglia utilizzo non autorizzato del contenuto di questo messaggio
costituisce violazione dell'obbligo di non prendere cognizione della
corrispondenza tra gli altri soggetti, salvo più grave illecito, ed
espone il responsabile alle relative conseguenze.

Confidentiality Notice. This electronic mail transmission may contain
legally priviledge and/or confidential information. Do not read this if
you are not the person(s) named.
Any use, distribution, copying or disclosure by any other person is
stricly prohibited (DL 196/03).
If you received this trasmission in error, please notify the sender and
destroy the original transmission and its attachments without reading or
saving in any manner.
---------------------------


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe [email protected] < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail [email protected].*
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.