I recently upgraded to the 2.4.21 kernel with the ACPI patch for 2.4.21-rc3,
which I've read on other lists is supposed to work. I can boot, and ACPI
seems to be working but my touchpad stops working along with my wifi card.
Usually, orinoco_cs is loaded to handle the wifi, but it won't loae with ACPI
enabled. The outputs from dmesg and /var/log/messages follow:
DMESG:
Linux version 2.4.21 ([email protected]) (gcc version 3.2.2 20030222
(Red Hat Linux 3.2.2-4)) #2 S
at Jun 14 18:48:29 PDT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
BIOS-e820: 000000001ffd0000 - 000000001ffe0000 (ACPI data)
BIOS-e820: 000000001ffe0000 - 0000000020000000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 131024
zone(0): 4096 pages.
zone(1): 126928 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 TOSHIB ) @ 0x000f0180
ACPI: RSDT (v001 TOSHIB 5100 08194.01032) @ 0x1ffd0000
ACPI: FADT (v002 TOSHIB 5100 08194.01032) @ 0x1ffd0058
ACPI: DBGP (v001 TOSHIB 5100 08194.01032) @ 0x1ffd00dc
ACPI: BOOT (v001 TOSHIB 5100 08194.01032) @ 0x1ffd0030
ACPI: DSDT (v001 TOSHIB 5100 08194.01032) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
Kernel command line: ro root=LABEL=/ hdc=ide-scsi vga=1280x1024
ide_setup: hdc=ide-scsi
No local APIC present or hardware disabled
Initializing CPU#0
Detected 1794.225 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3578.26 BogoMIPS
Memory: 514904k/524096k available (1427k kernel code, 8804k reserved, 522k
data, 152k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febf9ff 00000000 00000000 00000000
CPU: Common caps: 3febf9ff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.80GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030522
PCI: PCI BIOS revision 2.10 entry at 0xfcd8a, last bus=5
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 S4 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 11 12, disabled)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *6 7 10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 *7 10 11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *4 6 7 10 11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12, disabled)
ACPI: PCI Interrupt Link [LNKG] (IRQs *5)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 10 11 12, disabled)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Fan [FAN0] (off)
ACPI: Fan [FAN1] (off)
ACPI: Processor [CPU0] (supports C1 C2 C3, 2 performance states)
ACPI: Thermal Zone [THRM] (70 C)
Toshiba Laptop ACPI Extras version 0.15
vesafb: framebuffer at 0xd8000000, mapped to 0xe0815000, size 2000k
vesafb: mode is 640x400x8, linelength=640, pages=14
vesafb: protected mode interface info at c000:e720
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 80x25
fb0: VESA VGA frame buffer device
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
PCI: Enabling device 00:1f.6 (0000 -> 0001)
Real Time Clock Driver v1.10e
floppy0: no floppy controllers found
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 00:1f.1
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xcfa0-0xcfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xcfa8-0xcfaf, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK6021GAS, ATA DISK drive
blk: queue c03538c0, I/O limit 4095Mb (mask 0xffffffff)
hdc: UJDA730 DVD/CDRW, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 117210240 sectors (60012 MB), CHS=7296/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 > hda3
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 146k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 152k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 19:04:41 Jun 14 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xefe0, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xef80, IRQ 7
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling device 00:1d.2 (0000 -> 0001)
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x1000, IRQ 6
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
hub.c: new USB device 00:1d.1-2, assigned address 2
: USB HID v1.00 Mouse [Synaptics Inc. Synaptics cPad] on usb2:2.0
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
Adding Swap: 1052184k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MATSHITA Model: UJDA730 DVD/CDRW Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
ohci1394: $Rev: 896 $ Ben Collins <[email protected]>
PCI: Enabling device 02:07.0 (0000 -> 0002)
PCI: Setting latency timer of device 02:07.0 to 64
ohci1394_0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394_0: Runaway loop while stopping context: ...
ohci1394_0: Runaway loop while stopping context: ...
ohci1394_0: Runaway loop while stopping context: ...
ohci1394_0: Runaway loop while stopping context: ...
ohci1394_0: OHCI-1394 165.165 (PCI): IRQ=[11] MMIO=[20000800-20000fff] Max
Packet=[65536]
ohci1394_0: Set PHY Reg timeout [0xffffffff/0x00004000/100]
ohci1394_0: Runaway loop while stopping context: ...
ohci1394_0: Runaway loop while stopping context: ...
ohci1394_0: Runaway loop while stopping context: ...
ohci1394_0: Runaway loop while stopping context: ...
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
ip_tables: (C) 2000-2002 Netfilter core team
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<[email protected]> and others
divert: allocating divert_blk for eth0
eth0: OEM i82557/i82558 10/100 Ethernet, 00:00:39:62:A9:BA, IRQ 4.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4363 Sat Apr
19 17:46:46 PDT 2003
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Intel i845 chipset
agpgart: AGP aperture is 256M @ 0xe0000000
hub.c: new USB device 00:1d.0-2, assigned address 2
usb-uhci.c: interrupt, status 2, frame# 1625
: USB HID v1.00 Mouse [0461:4d09] on usb1:2.0
hermes.c: 4 Dec 2002 David Gibson <[email protected]>
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services
/var/log/messages:
Jun 14 19:23:37 localhost kernel: hub.c: new USB device 00:1d.0-2, assigned
address 2
Jun 14 19:23:37 localhost kernel: usb-uhci.c: interrupt, status 2, frame# 1625
Jun 14 19:23:37 localhost kernel: : USB HID v1.00 Mouse [0461:4d09] on
usb1:2.0
Jun 14 19:23:41 localhost /etc/hotplug/usb.agent: Setup hid for USB product
461/4d09/10
Jun 14 19:23:41 localhost /etc/hotplug/usb.agent: Setup mousedev for USB
product 461/4d09/10
Jun 14 19:23:41 localhost devlabel: devlabel service started/restarted
Jun 14 19:23:57 localhost modprobe: modprobe: Can't locate module
char-major-10-134
Jun 14 19:24:29 localhost kernel: Linux Kernel Card Services 3.1.22
Jun 14 19:24:29 localhost kernel: options: [pci] [cardbus] [pm]
Jun 14 19:24:29 localhost kernel: ds: no socket drivers loaded!
Jun 14 19:24:29 localhost kernel: unloading Kernel Card Services
-------------------------------------------------------
This SF.NET email is sponsored by: eBay
Great deals on office technology -- on eBay now! Click here:
http://adfarm.mediaplex.com/ad/ck/711-11697-6916-5
lmpx.com only provides a reader for public news (NNTP) servers. It is not
affiliated with the servers or forums shown here and is not responsible for
the content of articles, which is written by their respective authors.