at76c505a and berliOS driver

Hello.

Configuration:

FC2 with 2.6.7-1.494.2.2 kernel
atmel at76c505a
USB ids 03eb:7614
berliOS driver v0.12beta14

Aug 10 00:41:00 leshik kernel: usb 5-1: new full speed USB device using 
address 2
Aug 10 00:41:00 leshik kernel: /usr/src/at76c503a/usbdfu.c: USB Device 
Firmware Upgrade (DFU) handler v0.12beta14 loading
Aug 10 00:41:00 leshik kernel: /usr/src/at76c503a/at76c503.c: Generic 
Atmel at76c503/at76c505 routines v0.12beta14
Aug 10 00:41:00 leshik kernel: /usr/src/at76c503a/at76c503-fw_skel.c: 
Atmel at76c505a (RFMD2958) Wireless LAN Driver v0.12beta14 loading
Aug 10 00:41:00 leshik kernel: /usr/src/at76c503a/at76c503.c: $Id: 
at76c503.c,v 1.61 2004/06/29 21:26:24 jal2 Exp $ compiled Aug 10 2004 
00:18:24
Aug 10 00:41:00 leshik kernel: /usr/src/at76c503a/at76c503.c: firmware 
version 1.103.0 #164 (fcs_len 4)
Aug 10 00:41:00 leshik kernel: /usr/src/at76c503a/at76c503.c: device's 
MAC 00:06:f4:06:e0:01, regulatory domain ETSI (Europe - (Spain+France) 
(id 48)
Aug 10 00:41:00 leshik kernel: /usr/src/at76c503a/at76c503.c: registered 
wlan0
Aug 10 00:41:00 leshik kernel: usbcore: registered new driver 
at76c505a-rfmd2958

Problem 1 (already posted trouble):

There is wrong case string in at76c502.c (line 972)

  case BOARDTYPE_505_RFMD_2958:

but in the header file the corresponding constant is

  #define BOARDTYPE_505A_RFMD_2958    7

with 'A' after 505

therefore, the first time i have inserted USB card the driver reported:

Bad board type set (7).  Unable to get hardware config.

Solving 1:

Just change BOARDTYPE_505_RFMD_2958: to    case 
BOARDTYPE_505A_RFMD_2958: in at76c502.c

Problem 2:

When trying to "ifup wlan0" -

Aug 10 00:43:38 leshik kernel: usb 5-1: control timeout on ep0in
Aug 10 00:43:38 leshik kernel: /usr/src/at76c503a/at76c503.c: wlan0: 
get_cmd_status failed: -110
Aug 10 00:43:38 leshik kernel: /usr/src/at76c503a/at76c503.c: wlan0 
start_scan completed with -110
Aug 10 00:44:26 leshik kernel: usb 5-1: control timeout on ep0out
Aug 10 00:44:26 leshik kernel: /usr/src/at76c503a/at76c503.c: wlan0: 
set_card_command(CMD_RADIO) failed: -110
Aug 10 00:45:44 leshik kernel: usb 5-1: control timeout on ep0out
Aug 10 00:45:44 leshik kernel: /usr/src/at76c503a/at76c503.c: wlan0: 
set_card_command failed: -110


Solving 2:

i added same timeout in get_cmd_status in  at76c502.c

static inline
int get_cmd_status(struct usb_device *udev,
          u8 cmd, u8 *cmd_status)
{
   return usb_control_msg(udev, usb_rcvctrlpipe(udev,0),
                  0x22, INTERFACE_VENDOR_REQUEST_IN,
                  cmd, 0,
                  cmd_status, 40, HZ * USB_CTRL_GET_TIMEOUT);  <--- line 
1041
}

and in set_card_command

static
int set_card_command(struct usb_device *udev, int cmd,
           unsigned char *buf, int buf_size)
{
   int ret;
   struct at76c503_command *cmd_buf =
       (struct at76c503_command *)kmalloc(
           sizeof(struct at76c503_command) + buf_size,
           GFP_KERNEL);

   if(cmd_buf){
       cmd_buf->cmd = cmd;
       cmd_buf->reserved = 0;
       cmd_buf->size = cpu_to_le16(buf_size);
       if(buf_size > 0)
           memcpy(&(cmd_buf[1]), buf, buf_size);
       ret = usb_control_msg(udev, usb_sndctrlpipe(udev,0),
                     0x0e, DEVICE_VENDOR_REQUEST_OUT,
                     0, 0,
                     cmd_buf,
                     sizeof(struct at76c503_command) + buf_size,
                     HZ * 
USB_CTRL_GET_TIMEOUT);                          <-- line 1106
       kfree(cmd_buf);
       return ret;
   }

   return -ENOMEM;
}

then make && make install

and everything works fine now :)

Thanks all, hope it'll be usefull.