DFE 570 TX not working.

Dear List,


I'm just trying to make a DFE 570 TX (4 ports board) work under Linux=20
Kernel 2.4.23. The board goes up but I can't ping anything. I don't even=20
get a "Destination unreacheable" error message"!

I already tried the tulip module and the de4x5 module. I already checked=20
that I'm using the correct port.

I include here the output of "tulip-diag -aemf":

tulip-diag.c:v2.17 5/6/2003 Donald Becker ([email protected])
 http://www.scyld.com/diag/index.html
Index #1: Found a Digital DS21143 Tulip adapter at 0x9800.
Digital DS21143 Tulip chip registers at 0x9800:
 0x00: f8208400 ffffffff ffffffff 0e5bd000 0e5bd080 f0660000 320c2002 f3f=
f8065
 0x40: e0000000 fffdc3ff ffffffff 00000000 000020c7 ffff0001 ffffffff 8ff=
10000
 Port selection is MII, half-duplex.
 Transmit started, Receive started.
  The Rx process state is 'Waiting for packets'.
  The Tx process state is 'Idle'.
  The transmit threshold is 128.
  The NWay status register is 000020c7.
EEPROM 64 words, 6 address bits.
PCI Subsystem IDs, vendor 1186, device 1112.
CardBus Information Structure at offset 00000000.
Ethernet MAC Station Address 00:80:C8:B9:3F:F5.
EEPROM transceiver/media description table.
Leaf node at offset 30, default media type 0800 (Autosense).
 1 transceiver description blocks:
  Media MII, block type 3, length 13.
   MII interface PHY 0 (media type 11).
   21143 MII initialization sequence is 0 words:.
   21143 MII reset sequence is 0 words:.
    Media capabilities are 7800, advertising 01e1.
    Full-duplex map 5000, Threshold map 1800.
    No MII interrupt.
 MII PHY found at address 1, status 0x784d.
  Internal autonegotiation state is 'Ability detect'.
Index #2: Found a Digital DS21143 Tulip adapter at 0x9400.
Digital DS21143 Tulip chip registers at 0x9400:
 0x00: f8000000 ffffffff ffffffff 0e5bb000 0e5bb080 f0000000 32040040 f3f=
e0000
 0x40: e0000000 ffffcbf8 ffffffff 00000000 000000c6 ffff0000 ffffffff 8ff=
00000
 Port selection is MII, half-duplex.
 Transmit stopped, Receive stopped.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 128.
  The NWay status register is 000000c6.
EEPROM 64 words, 6 address bits.
PCI Subsystem IDs, vendor 1186, device 1112.
CardBus Information Structure at offset 00000000.
Ethernet MAC Station Address 00:80:C8:B9:3F:F6.
EEPROM transceiver/media description table.
Leaf node at offset 30, default media type 0800 (Autosense).
 1 transceiver description blocks:
  Media MII, block type 3, length 13.
   MII interface PHY 0 (media type 11).
   21143 MII initialization sequence is 0 words:.
   21143 MII reset sequence is 0 words:.
    Media capabilities are 7800, advertising 01e1.
    Full-duplex map 5000, Threshold map 1800.
    No MII interrupt.
 MII PHY found at address 1, status 0x7849.
  Internal autonegotiation state is 'Autonegotiation disabled'.
Index #3: Found a Digital DS21143 Tulip adapter at 0x9000.
Digital DS21143 Tulip chip registers at 0x9000:
 0x00: f8000000 ffffffff ffffffff 0e5ba000 0e5ba080 f0000000 32040040 f3f=
e0000
 0x40: e0000000 ffffcbf8 ffffffff 00000000 000000c6 ffff0000 ffffffff 8ff=
00000
 Port selection is MII, half-duplex.
 Transmit stopped, Receive stopped.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 128.
  The NWay status register is 000000c6.
EEPROM 64 words, 6 address bits.
PCI Subsystem IDs, vendor 1186, device 1112.
CardBus Information Structure at offset 00000000.
Ethernet MAC Station Address 00:80:C8:B9:3F:F7.
EEPROM transceiver/media description table.
Leaf node at offset 30, default media type 0800 (Autosense).
 1 transceiver description blocks:
  Media MII, block type 3, length 13.
   MII interface PHY 0 (media type 11).
   21143 MII initialization sequence is 0 words:.
   21143 MII reset sequence is 0 words:.
    Media capabilities are 7800, advertising 01e1.
    Full-duplex map 5000, Threshold map 1800.
    No MII interrupt.
 MII PHY found at address 1, status 0x7849.
  Internal autonegotiation state is 'Autonegotiation disabled'.
Index #4: Found a Digital DS21143 Tulip adapter at 0x8800.
Digital DS21143 Tulip chip registers at 0x8800:
 0x00: f8000000 ffffffff ffffffff 0e5b9000 0e5b9080 f0000000 32040040 f3f=
e0000
 0x40: e0000000 ffffcbf8 ffffffff 00000000 000000c6 ffff0000 ffffffff 8ff=
0c000
 Port selection is MII, half-duplex.
 Transmit stopped, Receive stopped.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 128.
  The NWay status register is 000000c6.
EEPROM 64 words, 6 address bits.
PCI Subsystem IDs, vendor 1186, device 1112.
CardBus Information Structure at offset 00000000.
Ethernet MAC Station Address 00:80:C8:B9:3F:F8.
EEPROM transceiver/media description table.
Leaf node at offset 30, default media type 0800 (Autosense).
 1 transceiver description blocks:
  Media MII, block type 3, length 13.
   MII interface PHY 0 (media type 11).
   21143 MII initialization sequence is 0 words:.
   21143 MII reset sequence is 0 words:.
    Media capabilities are 7800, advertising 01e1.
    Full-duplex map 5000, Threshold map 1800.
    No MII interrupt.
 MII PHY found at address 1, status 0x7849.
  Internal autonegotiation state is 'Autonegotiation disabled'.



Any idea of what could be wrong?

I can try Donald's driver but I believe it isn't the recommended solution=
 for a 2.4.x kernel.


TIA,

Rodrigo Severo

--=20
----------------------------------------------------
Rodrigo Severo
F=E1brica de Id=E9ias
Fone: +55(61)321 1357
Fax: +55(61)223 1712
SBS - Quadra 2 - Ed. Empire Center - Sala 1301
Bras=EDlia/DF - Brasil
CEP: 70.070-904
----------------------------------------------------

_______________________________________________
tulip mailing list, [email protected]
To change to digest mode or unsubscribe visit
http://www.scyld.com/mailman/listinfo/tulip