Re: help with firmware update on R610...
Bruce Ferrell <[email protected]>
| Newsgroups | gmane.linux.hardware.dell.poweredge |
|---|---|
| Message-ID | <[email protected]> |
I have the same issue (symptom anyway) When I perform the steps outlined, sasdupie fails with a segmentation fault. inv.xml is zero length. debug.log is attached. No files in /var/log/dell/updatepackage/log/support/ sasdupie[20566]: segfault at 20 ip 00007f7c10ef500d sp 00007fff7703f950 error 4 in sasdupie[7f7c10ed0000+110000] On 07/22/2015 10:06 PM, [email protected] wrote: > > *Dell - Internal Use - Confidential * > > Hi Becky, > > > > Please provide logs from your system and following are steps to collect the debug logs . > > > > 1.Extract dup by running the command ".\SAS-RAID_Firmware_F96NR_LN_6.3.3-0002_X00.BIN--extract \tmp\dup_extract_dir" > > 2.Change to the extracted directory by running “cd \tmp\dup_extract_dir “. > > 4.Copy the payload directory up one level, “cp payload\* . “ . > > 5.Run “sasdupie -i -o inv.xml -debug" for inventory > > 7.Send us files inv.xml, debug.log, package.xml and Dell customer logs from > > /var/log/dell/updatepackage/log/ and /var/log/dell/updatepackage/log/support directories. > > > > Thanks > > Santosh > > > > *From:*linux-poweredge-bounces-Lists *On Behalf Of *Becky Ligon > *Sent:* Thursday, July 23, 2015 1:20 AM > *To:* linux-poweredge-Lists > *Subject:* [Linux-PowerEdge] help with firmware update on R610... > > > > All: > > When I run the firmware update for the PERC 6/i, I am getting this error: > > Collecting inventory... > ...... > Inventory collection failed. > > Where can I find information regarding this error? log files? Is it possible that the inventory collection system is not setup correctly on the machine? > > I am running SAS-RAID_Firmware_F96NR_LN_6.3.3-0002_X00.BIN. > > > > Any suggestions will be helpful! > > Becky > > > > -- > > Becky Ligon > Research Associate > Clemson University > Clemson, SC > > > > _______________________________________________ > Linux-PowerEdge mailing list > [email protected] > https://lists.us.dell.com/mailman/listinfo/linux-poweredge _______________________________________________ Linux-PowerEdge mailing list [email protected] https://lists.us.dell.com/mailman/listinfo/linux-poweredge
debug.log
(text/plain, 22.2 KB)
<07/22/15, 10:29:03 PM>=============================================== <07/22/15, 10:29:03 PM><07/22/15, 10:29:03 PM>DUPWrapper: Logging enabled <07/22/15, 10:29:03 PM>CDeviceEnumeratorIPMI::populateDeviceVector -> Start <07/22/15, 10:29:03 PM>In ProcessCommand : Start <07/22/15, 10:29:03 PM>In ProcessCommand: IPMI command:failed: status:4289 <07/22/15, 10:29:03 PM> In populateDeviceVector:: BACKPLANE_TOPOLOGY failed <07/22/15, 10:29:03 PM>DeviceEnum::populateDeviceVector2: Begin <07/22/15, 10:29:04 PM>DeviceEnum::populateDeviceVector: Using Lib index:0 <07/22/15, 10:29:04 PM>DeviceEnum::populateDeviceVector: Using StoreLib <07/22/15, 10:29:04 PM>doProcessLibCommand: Calling ProcessLibCommand <07/22/15, 10:29:04 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:04 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:04 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:04 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:04 PM>ProcessLibCommand 1: Loading a StoreLib <07/22/15, 10:29:04 PM>ProcessLibCommand 1: loading library:libstorelib.so.3 <07/22/15, 10:29:04 PM>DUPStoreLibTalker::ProcessLibCommand 1: m_NeedRemoveUtilsRpm is false <07/22/15, 10:29:04 PM>DUPStoreLibTalker::installStorelibLibUtils: begin <07/22/15, 10:29:05 PM>DUPStoreLibTalker::installStorelibLibUtils: After doRPM <07/22/15, 10:29:05 PM>DUPStoreLibTalker::installStorelibLibUtils: RPM already installed <07/22/15, 10:29:05 PM>DUPStoreLibTalker::installStorelibLibUtils: Returning false <07/22/15, 10:29:05 PM>DUPStoreLibTalker::ProcessLibCommand 1: m_NeedRemoveUtilsRpm is false <07/22/15, 10:29:05 PM>ProcessLibCommand 1: loading library:./libstorelib.so <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:05 PM>doProcessLibCommand: After Calling ProcessLibCommand <07/22/15, 10:29:05 PM>DeviceEnum::populateDeviceVector: Got some controllers <07/22/15, 10:29:05 PM>DeviceEnum::populateDeviceVector: Begin new controller --------- <07/22/15, 10:29:05 PM>DeviceEnum:populateDeviceVector: libIndex=0 <07/22/15, 10:29:05 PM>DeviceEnum:populateDeviceVector: Using StoreLib <07/22/15, 10:29:05 PM>DeviceEnum:populateDeviceVector: ctrlid:0 index:0 <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: New Device m_CtrlId=0 DeviceID=fffe <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: m_strEnumId =CtrlId 0 DeviceId fffe <07/22/15, 10:29:05 PM>DUPControllerDevice: Creating DUPControllerDevice<07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>DUPControllerDevice: FW = <07/22/15, 10:29:05 PM>6.2.0-0013<07/22/15, 10:29:05 PM> <07/22/15, 10:29:05 PM>DUPControllerDevice: Name = <07/22/15, 10:29:05 PM>PERC 6/i Integrated Controller 0<07/22/15, 10:29:05 PM> <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>PERCDUPDevice created <07/22/15, 10:29:05 PM>PERCDUPDevice:isEnclosureHotPlugable: checking hotplugable <07/22/15, 10:29:05 PM>Begin DeviceEnumerator:isValidDevice <07/22/15, 10:29:05 PM>DeviceEnumerator::isValidDevice:enclosureDevice == NULL <07/22/15, 10:29:05 PM>DUPEnumerator: Returning true. <07/22/15, 10:29:05 PM>DeviceEnum::populateDeviceVector: Querying physical devices attached to Controller <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>DeviceEnum:populateDeviceVector:There are 6 Devices attached <07/22/15, 10:29:05 PM>DeviceEnum::populateDevVec:Begin new device --------- <07/22/15, 10:29:05 PM>DeiceEnum:populateDevVec:Found device ctrlID=0 deviceID=0 <07/22/15, 10:29:05 PM>DeiceEnum:populateDevVec: found a device of type:0 <07/22/15, 10:29:05 PM>DeviceEnumerator:populateDeviceVector: Got an Disk <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>DeviceEnumerator::got a SAS->SATA disk <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: New Device m_CtrlId=0 DeviceID=0 <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: m_strEnumId =CtrlId 0 DeviceId 0 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice created <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice(): New device for ctrlID:0 deviceID:0 <07/22/15, 10:29:05 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:05 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:05 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:05 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice::setName:Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:05 PM>ProductID = ST31000524NS <07/22/15, 10:29:05 PM>Version = KA0A <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice(): Calling setSATADriveID() <07/22/15, 10:29:05 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:05 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:05 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:05 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice::setSATADriveID: Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:21739 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:1739 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:739 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:39 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:9 <07/22/15, 10:29:05 PM>The deviceId = 21739 <07/22/15, 10:29:05 PM>Begin DeviceEnumerator:isValidDevice <07/22/15, 10:29:05 PM>DeviceEnumerator::isValidDevice:enclosureDevice == NULL <07/22/15, 10:29:05 PM>DUPEnumerator: Returning true. <07/22/15, 10:29:05 PM>DeviceEnum::populateDevVec:Begin new device --------- <07/22/15, 10:29:05 PM>DeiceEnum:populateDevVec:Found device ctrlID=0 deviceID=1 <07/22/15, 10:29:05 PM>DeiceEnum:populateDevVec: found a device of type:0 <07/22/15, 10:29:05 PM>DeviceEnumerator:populateDeviceVector: Got an Disk <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>DeviceEnumerator::got a SAS->SATA disk <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: New Device m_CtrlId=0 DeviceID=1 <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: m_strEnumId =CtrlId 0 DeviceId 1 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice created <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice(): New device for ctrlID:0 deviceID:1 <07/22/15, 10:29:05 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:05 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:05 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:05 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice::setName:Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:05 PM>ProductID = ST31000524NS <07/22/15, 10:29:05 PM>Version = KA0A <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice(): Calling setSATADriveID() <07/22/15, 10:29:05 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:05 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:05 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:05 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice::setSATADriveID: Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:21739 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:1739 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:739 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:39 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice:: Showing char:9 <07/22/15, 10:29:05 PM>The deviceId = 21739 <07/22/15, 10:29:05 PM>Begin DeviceEnumerator:isValidDevice <07/22/15, 10:29:05 PM>DeviceEnumerator::isValidDevice:enclosureDevice == NULL <07/22/15, 10:29:05 PM>DUPEnumerator: Returning true. <07/22/15, 10:29:05 PM>DeviceEnum::populateDevVec:Begin new device --------- <07/22/15, 10:29:05 PM>DeiceEnum:populateDevVec:Found device ctrlID=0 deviceID=2 <07/22/15, 10:29:05 PM>DeiceEnum:populateDevVec: found a device of type:0 <07/22/15, 10:29:05 PM>DeviceEnumerator:populateDeviceVector: Got an Disk <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>DeviceEnumerator::got a SAS->SATA disk <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: New Device m_CtrlId=0 DeviceID=2 <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: m_strEnumId =CtrlId 0 DeviceId 2 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice created <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice(): New device for ctrlID:0 deviceID:2 <07/22/15, 10:29:05 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:05 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:05 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:05 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice::setName:Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:05 PM>ProductID = GB1000EAFJL <07/22/15, 10:29:05 PM>Version = HPGC <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice(): Calling setSATADriveID() <07/22/15, 10:29:05 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:05 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:05 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:05 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice::setSATADriveID: Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice::setSATADriveID: Not a supported SATA HDD. Using 00000 <07/22/15, 10:29:05 PM>Begin DeviceEnumerator:isValidDevice <07/22/15, 10:29:05 PM>DeviceEnumerator::isValidDevice:enclosureDevice == NULL <07/22/15, 10:29:05 PM>DUPEnumerator: Returning true. <07/22/15, 10:29:05 PM>DeviceEnum::populateDevVec:Begin new device --------- <07/22/15, 10:29:05 PM>DeiceEnum:populateDevVec:Found device ctrlID=0 deviceID=3 <07/22/15, 10:29:05 PM>DeiceEnum:populateDevVec: found a device of type:0 <07/22/15, 10:29:05 PM>DeviceEnumerator:populateDeviceVector: Got an Disk <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>DeviceEnumerator::got a SAS->SATA disk <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: New Device m_CtrlId=0 DeviceID=3 <07/22/15, 10:29:05 PM>DUPDevice::DUPDevice: m_strEnumId =CtrlId 0 DeviceId 3 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice created <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice(): New device for ctrlID:0 deviceID:3 <07/22/15, 10:29:05 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:05 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:05 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:05 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:05 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice::setName:Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:05 PM>ProductID = WDC WD2003FYYS-0 <07/22/15, 10:29:05 PM>Version = 1D01 <07/22/15, 10:29:05 PM>SASHardDriveDUPDevice(): Calling setSATADriveID() <07/22/15, 10:29:05 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:05 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:05 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:05 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:05 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:06 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:06 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:06 PM>SASHardDriveDUPDevice::setSATADriveID: Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:06 PM>SASHardDriveDUPDevice::setSATADriveID: Not a supported SATA HDD. Using 00000 <07/22/15, 10:29:06 PM>Begin DeviceEnumerator:isValidDevice <07/22/15, 10:29:06 PM>DeviceEnumerator::isValidDevice:enclosureDevice == NULL <07/22/15, 10:29:06 PM>DUPEnumerator: Returning true. <07/22/15, 10:29:06 PM>DeviceEnum::populateDevVec:Begin new device --------- <07/22/15, 10:29:06 PM>DeiceEnum:populateDevVec:Found device ctrlID=0 deviceID=4 <07/22/15, 10:29:06 PM>DeiceEnum:populateDevVec: found a device of type:0 <07/22/15, 10:29:06 PM>DeviceEnumerator:populateDeviceVector: Got an Disk <07/22/15, 10:29:06 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:06 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:06 PM>DeviceEnumerator::got a SAS->SATA disk <07/22/15, 10:29:06 PM>DUPDevice::DUPDevice: New Device m_CtrlId=0 DeviceID=4 <07/22/15, 10:29:06 PM>DUPDevice::DUPDevice: m_strEnumId =CtrlId 0 DeviceId 4 <07/22/15, 10:29:06 PM>SASHardDriveDUPDevice created <07/22/15, 10:29:06 PM>SASHardDriveDUPDevice(): New device for ctrlID:0 deviceID:4 <07/22/15, 10:29:06 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:06 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:06 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:06 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:06 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:06 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:06 PM>SASHardDriveDUPDevice::setName:Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:06 PM>ProductID = WDC WD2003FYYS-0 <07/22/15, 10:29:06 PM>Version = 1D01 <07/22/15, 10:29:06 PM>SASHardDriveDUPDevice(): Calling setSATADriveID() <07/22/15, 10:29:06 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:06 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:06 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:06 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:06 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:06 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:06 PM>SASHardDriveDUPDevice::setSATADriveID: Return code from SCSIPassThryLibCommand = 0 <07/22/15, 10:29:06 PM>SASHardDriveDUPDevice::setSATADriveID: Not a supported SATA HDD. Using 00000 <07/22/15, 10:29:06 PM>Begin DeviceEnumerator:isValidDevice <07/22/15, 10:29:06 PM>DeviceEnumerator::isValidDevice:enclosureDevice == NULL <07/22/15, 10:29:06 PM>DUPEnumerator: Returning true. <07/22/15, 10:29:06 PM>DeviceEnum::populateDevVec:Begin new device --------- <07/22/15, 10:29:06 PM>DeiceEnum:populateDevVec:Found device ctrlID=0 deviceID=20 <07/22/15, 10:29:06 PM>DeiceEnum:populateDevVec: found a device of type:d <07/22/15, 10:29:06 PM>DeviceEnum:populateDeviceVector: Got an Enclosure <07/22/15, 10:29:06 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:06 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:06 PM>DeviceEnumerator::getEnclosureType: Model number BACKPLANE 1.079AM02H0 <07/22/15, 10:29:06 PM>DeviceEnumerator:getEnclosureType: returning SAS_BACKPLANE <07/22/15, 10:29:06 PM>DeviceEnumerator:populateDeviceVector: Got Enclosure Type <07/22/15, 10:29:06 PM>DeviceEnumerator::populateDeviceVector: Creating SASBP device <07/22/15, 10:29:06 PM>DUPDevice::DUPDevice: New Device m_CtrlId=0 DeviceID=20 <07/22/15, 10:29:06 PM>DUPDevice::DUPDevice: m_strEnumId =CtrlId 0 DeviceId 20 <07/22/15, 10:29:06 PM>PESASBPDUPDevice created <07/22/15, 10:29:06 PM>Starting ReceiveDiagnostic <07/22/15, 10:29:06 PM>RECEIVE_DIAGNOSTIC new size=100 <07/22/15, 10:29:06 PM>DUPStoreLibTalker::ReceiveDiagnosticResult: Before SsiCommand <07/22/15, 10:29:06 PM>SCSIPassThrough 1: calling ProcessLibCommand <07/22/15, 10:29:06 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:06 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:06 PM>ProcessLibCommand 1: StoreLib <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 1: After Calling LSI <07/22/15, 10:29:06 PM>ProcessLibCommand 2 Exit <07/22/15, 10:29:06 PM>SCSIPassThrough 1: After calling ProcessLibCommand <07/22/15, 10:29:06 PM>SCSIPassThrough 1: GOOD calling ProcessLibCommand <07/22/15, 10:29:06 PM>DUPStoreLibTalker::ReceiveDiagnosticResult: After SsiCommand <07/22/15, 10:29:06 PM>Good return code from ScsiCommand number 2 <07/22/15, 10:29:06 PM>DUPEnclosureDevice: good setting version <07/22/15, 10:29:06 PM>DUPEnclosureDevice: FW SIM0:0.00 <07/22/15, 10:29:06 PM>DUPEnclosureDevice: FW SIM1:1.07 <07/22/15, 10:29:06 PM>DUPEnclosureDevice: scanning sims <07/22/15, 10:29:06 PM>DUPEnclosureDevice: setting DUPSTATUS_NOTPRESENT <07/22/15, 10:29:06 PM>Set SIM firmware for SIM 0 0.00 <07/22/15, 10:29:06 PM>SIM Update status for SIM0 7 <07/22/15, 10:29:06 PM>DUPEnclosureDevice: scanning sims <07/22/15, 10:29:06 PM>DUPEnclosureDevice: setting DUPSTATUS_NOTUPDATED <07/22/15, 10:29:06 PM>Set SIM firmware for SIM 1 1.07 <07/22/15, 10:29:06 PM>SIM Update status for SIM1 f <07/22/15, 10:29:06 PM>Begin DeviceEnumerator:isValidDevice <07/22/15, 10:29:06 PM>DeviceEnumerator::isValidDevice:enclosureDevice->m_SerialNumbersize == 0 <07/22/15, 10:29:06 PM>DeviceEnumerator::isValidDevice:enclosureDevice->hasBlankSerialNumber() <07/22/15, 10:29:06 PM>DeviceEnumerator::isValidDevice:enclosureDevice->getTPI() == 0 <07/22/15, 10:29:06 PM>DUPEnumerator: Returning true. <07/22/15, 10:29:06 PM>DeviceEnum::populateDeviceVector: Using Lib index:1 <07/22/15, 10:29:06 PM>DeviceEnumerator::populateDeviceVector: Using StoreLibIR <07/22/15, 10:29:06 PM>doProcessLibCommand: Calling ProcessLibCommand <07/22/15, 10:29:06 PM>ProcessLibCommand 2 calling ProcessLibCommand 1 <07/22/15, 10:29:06 PM>Starting ProcessLibCommand 1 <07/22/15, 10:29:06 PM>ProcessLibCommand 1: StoreLibIR <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Is a StoreLib loaded? <07/22/15, 10:29:06 PM>ProcessLibCommand 1: Loading a StoreLib <07/22/15, 10:29:06 PM>ProcessLibCommand 1: loading library:libstorelibir.so.5