Re: pcmcia problems with 2.6.0test11
"mrmailer" <[email protected]> Fri, 28 Nov 2003 16:13:15 -0500 (EST)
| Newsgroups | gmane.linux.pcmcia.devel |
|---|---|
| Message-ID | <[email protected]> |
for argument's sake, there are NO references to pcmcia in /etc/modprobe.conf, or ds, etc. everythine else is from default pcmcia-cs install on fedora core 1, aside from hermes.conf which is tailored to be used device "orinoco_cs" class "network" module "hermes", "orinoco", "orinoco_cs" # LinkSys WPC11 card "Instant Wireless Network PC Card" manfid 0x0156, 0x0002 #substitute your addresses from step 1 here bind "orinoco_cs" with booting kernel 2.4, i get the two beeps, as they should, and it turns on automatically. if i remove the card then reinsert it, it does the same, automatically. with 2.6, as mentioned, i have to manually modprobe yenta_socket and get no beeps, and if i remove it then plug it back in, i have to manually restart pcmcia. --- On Fri 11/28, mrmailer < [email protected] > wrote: From: mrmailer [mailto: [email protected]] To: [email protected] Date: Fri, 28 Nov 2003 14:31:04 -0500 (EST) Subject: Re: [Pcmcia-cs-devel]pcmcia problems with 2.6.0test11 <br>And as I've told you before, it's not. I have a default pcmcia-cs install on fc1. I had TRIED a post-install of yenta_socket in modprobe.conf, which did not fix the problem, so I removed it, so please do not try to use that as a scapegoat. I have a default configuration, period. This configuration works fine, and automatically, with a 2.4 kernel boot. I don't know how else to explain that to you.<br><br><br><br>I believe I already sent you a personal mail with the output of lsmod, but I will send it again to the list.<br><br><br><br>Module Size Used by<br><br>snd_pcm_oss 48452 0<br><br>snd_mixer_oss 17024 2 snd_pcm_oss<br><br>snd_ali5451 20548 1<br><br>snd_ac97_codec 52420 1 snd_ali5451<br><br>snd_pcm 87488 2 snd_pcm_oss,snd_ali5451<br><br>snd_page_alloc 9092 1 snd_pcm<br><br>snd_timer 21568 1 snd_pcm<br><br>snd 43780 6 snd_pcm_oss,snd_mixer_oss,sn d_ali5451,snd_ac97_codec,snd_pcm,snd_timer<br><br>soundcore 7040 2 snd<br><br>ide_cd 37248 0<br><br>cdrom 32928 1 ide_cd<br><br>lp 8544 0<br><br>ipv6 233952 12<br><br>orinoco_cs 6664 0<br><br>ds 11008 3 orinoco_cs<br><br>pcmcia_core 59136 2 orinoco_cs,ds<br><br>orinoco 42116 1 orinoco_cs<br><br>hermes 7808 2 orinoco_cs,orinoco<br><br>af_packet 13060 0<br><br>ipt_state 1408 2<br><br>iptable_filter 2176 1<br><br>iptable_nat 19364 0<br><br>ip_conntrack 27744 2 ipt_state,iptable_nat<br><br>ip_tables 15888 3 ipt_state,iptable_filter,iptable_nat<br><br>natsemi 22624 0<br><br>crc32 3840 1 natsemi<br><br>floppy 54772 0<br><br>sg 29708 0<br><br>scsi_mod 9 8980 1 sg<br><br>parport_pc 32780 1<br><br>parport 36352 2 lp,parport_pc<br><br>ehci_hcd 22080 0<br><br>ohci1394 31744 0<br><br>ieee1394 70732 1 ohci1394<br><br>nls_iso8859_1 3712 1<br><br>ntfs 87636 1<br><br>hid 30720 0<br><br>ohci_hcd 16320 0<br><br>usbcore 97236 5 ehci_hcd,hid,ohci_hcd<br><br>rtc 10728 0<br><br>unix 23628 618<br><br><br><br><br><br><br><br><br><br><br><br> --- On Fri 11/28, David Hinds < [email protected] > wrote:<br><br>From: David Hinds [mailto: [email protected]]<br><br>To: [email protected]<br><br>Date: Fri, 28 Nov 2003 11:05:44 -0800<br><br>Subject: Re: [Pcmcia-cs-devel]pcmcia problems with 2.6.0test11<br><br><br><br>On Fri, Nov 28, 2003 at 01:50:16PM -0500, mrmailer wrote:<br>> <br>> I had tried post install of yenta_socket for pcmcia_core, but to no<br>> av ail(my system uses modprobe.conf for 2.6 kernel) <br>> <br>> I also did, as recommended by some others on google, alias yenta<br>> yenta_socket and alias i82365 yenta_socket <br>> <br>> all of this produced nothing<br><br>As I've told you before, your setup is all screwed up.<br><br>You should not have any PCMCIA aliases. You should not post install<br>yenta_socket for pcmcia_core. You did not answer my question and show<br>your 'lsmod' output from when the PCMCIA startup script failed. If<br>modules.conf is your module config file, how about showing that? How<br>about trying to be a little more proactive about providing<br>information, instead of always answering only half of my questions?<br><br>> Is it possible to use the hotplug scripts w/o pcmcia-cs?<br><br>Not for PCMCIA cards, no.<br><br>-- Dave<br><br><br>_______________________________________________<br>No banners. No pop-ups. No kidding.<br>Introducing My Way - http://www.myway.com<br><br><br>------------- ------------------------------------------<br>This SF.net email is sponsored by: SF.net Giveback Program.<br>Does SourceForge.net help you be more productive? Does it<br>help you create better code? SHARE THE LOVE, and help us help<br>YOU! Click Here: http://sourceforge.net/donate/<br>_______________________________________________<br>Pcmcia-cs-devel mailing list<br>[email protected]<br>https://lists.sourceforge.net/lists/listinfo/pcmcia-cs-devel<br> _______________________________________________ No banners. No pop-ups. No kidding. Introducing My Way - http://www.myway.com ------------------------------------------------------- This SF.net email is sponsored by: SF.net Giveback Program. Does SourceForge.net help you be more productive? Does it help you create better code? SHARE THE LOVE, and help us help YOU! Click Here: http://sourceforge.net/donate/