Fwd: smartctl output for Crucial 512Gb SSD
Mike <[email protected]>
| Newsgroups | gmane.linux.utilities.smartmontools |
|---|---|
| Message-ID | <CABfcST9G8yHb3f=QxCYKezFiyET-5W35rDY_Ry52oq-DrddwoA@mail.gmail.com> |
Great thanks. I've applied the patch and ran the same command, which
initially takes around 30 seconds to return any data at all, it then
hung for about 1 minute after printing the GPL table. Here is the
output:
user@w530:~/Downloads/smartmontools-6.3$ sudo ./smartctl -x /dev/sdb
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-3.13.0-34-generic] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Crucial/Micron RealSSD m4/C400/P400
Device Model: M4-CT512M4SSD1
Serial Number: 000000001249091FCC21
LU WWN Device Id: 5 00a075 1091fcc21
Firmware Version: 070H
User Capacity: 512,110,190,592 bytes [512 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat Aug 16 21:43:33 2014 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Write SCT (Get) Feature Control Command failed: scsi error medium or
hardware error (serious)
Wt Cache Reorder: Unknown (SCT Feature Control command failed)
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: scsi error medium or hardware error (serious)
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 2380) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 39) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0
9 Power_On_Hours -O--CK 100 100 001 - 4439
12 Power_Cycle_Count -O--CK 100 100 001 - 515
170 Grown_Failing_Block_Ct PO--CK 100 100 010 - 0
171 Program_Fail_Count -O--CK 100 100 001 - 0
172 Erase_Fail_Count -O--CK 100 100 001 - 0
173 Wear_Leveling_Count PO--CK 100 100 010 - 0
174 Unexpect_Power_Loss_Ct -O--CK 100 100 001 - 398
181 Non4k_Aligned_Access -O---K 100 100 001 - 144 45 99
183 SATA_Iface_Downshift -O--CK 100 100 001 - 0
184 End-to-End_Error PO--CK 100 100 050 - 0
187 Reported_Uncorrect -O--CK 100 100 001 - 0
188 Command_Timeout -O--CK 100 100 001 - 0
189 Factory_Bad_Block_Ct -OSR-- 100 100 001 - 215
194 Temperature_Celsius -O---K 100 100 000 - 0
195 Hardware_ECC_Recovered -O-RCK 100 100 001 - 0
196 Reallocated_Event_Count -O--CK 100 100 001 - 0
197 Current_Pending_Sector -O--CK 100 100 001 - 0
198 Offline_Uncorrectable ----CK 100 100 001 - 0
199 UDMA_CRC_Error_Count -O--CK 100 100 001 - 0
202 Perc_Rated_Life_Used ---RC- 100 100 001 - 0
206 Write_Error_Rate -OSR-- 100 100 001 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
Read SMART Log Directory failed: scsi error medium or hardware error (serious)
General Purpose Log Directory Version 1
Address Access R/W Size Description
0x00 GPL R/O 1 Log Directory
0x03 GPL R/O 16383 Ext. Comprehensive SMART error log
0x04 GPL R/O 255 Device Statistics log
0x07 GPL R/O 3449 Extended self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x80-0x9f GPL R/W 16 Host vendor specific log
0xa0 GPL VS 2000 Device vendor specific log
0xa1-0xbf GPL VS 1 Device vendor specific log
0xc0 GPL VS 80 Device vendor specific log
0xc1-0xdf GPL VS 1 Device vendor specific log
0xe0 GPL R/W 1 SCT Command/Status
0xe1 GPL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (16383 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (3449 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Read SMART Selective Self-test Log failed: scsi error medium or
hardware error (serious)
SCT Status Version: 3
SCT Version (vendor specific): 1 (0x0001)
SCT Support Level: 0
Device State: Active (0)
Current Temperature: 0 Celsius
Power Cycle Max Temperature: 0 Celsius
Lifetime Max Temperature: 0 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 10 minutes
Temperature Logging Interval: 10 minutes
Min/Max recommended Temperature: 0/70 Celsius
Min/Max Temperature Limit: -5/75 Celsius
Temperature History Size (Index): 478 (37)
Index Estimated Time Temperature Celsius
38 2014-08-13 14:10 ? -
... ..(476 skipped). .. -
37 2014-08-16 21:40 ? -
Write SCT (Get) Error Recovery Control Command failed: scsi error
medium or hardware error (serious)
SCT (Get) Error Recovery Control command failed
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 2) ==
1 0x008 4 515 Lifetime Power-On Resets
1 0x010 4 4439 Power-on Hours
1 0x018 6 933634265 Logical Sectors Written
1 0x020 6 2708986 Number of Write Commands
1 0x028 6 852431906 Logical Sectors Read
1 0x030 6 6049196 Number of Read Commands
4 ===== = = == General Errors Statistics (rev 1) ==
4 0x008 4 0 Number of Reported Uncorrectable Errors
4 0x010 4 0 Resets Between Cmd Acceptance and Completion
5 ===== = = == Temperature Statistics (rev 1) ==
5 0x008 1 0 Current Temperature
5 0x010 1 0 Average Short Term Temperature
5 0x018 1 0 Average Long Term Temperature
5 0x020 1 0 Highest Temperature
5 0x028 1 0 Lowest Temperature
5 0x030 1 0 Highest Average Short Term Temperature
5 0x038 1 0 Lowest Average Short Term Temperature
5 0x040 1 0 Highest Average Long Term Temperature
5 0x048 1 0 Lowest Average Long Term Temperature
5 0x050 4 - Time in Over-Temperature
5 0x058 1 70 Specified Maximum Operating Temperature
5 0x060 4 - Time in Under-Temperature
5 0x068 1 0 Specified Minimum Operating Temperature
6 ===== = = == Transport Statistics (rev 1) ==
6 0x008 4 0 Number of Hardware Resets
6 0x010 4 0 Number of ASR Events
6 0x018 4 0 Number of Interface CRC Errors
7 ===== = = == Solid State Device Statistics (rev 1) ==
7 0x008 1 21~ Percentage Used Endurance Indicator
|_ ~ normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
I then ran a -t short and a --test=long, and then issued the same
command as above:
user@w530:~/Downloads/smartmontools-6.3$ sudo ./smartctl -x /dev/sdb
[sudo] password for user:
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-3.13.0-34-generic] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Crucial/Micron RealSSD m4/C400/P400
Device Model: M4-CT512M4SSD1
Serial Number: 000000001249091FCC21
LU WWN Device Id: 5 00a075 1091fcc21
Firmware Version: 070H
User Capacity: 512,110,190,592 bytes [512 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat Aug 16 22:44:54 2014 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Write SCT (Get) Feature Control Command failed: scsi error medium or
hardware error (serious)
Wt Cache Reorder: Unknown (SCT Feature Control command failed)
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: scsi error medium or hardware error (serious)
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 80) The previous self-test completed having
the electrical element of the test
failed.
Total time to complete Offline
data collection: ( 2380) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 39) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0
9 Power_On_Hours -O--CK 100 100 001 - 4440
12 Power_Cycle_Count -O--CK 100 100 001 - 515
170 Grown_Failing_Block_Ct PO--CK 100 100 010 - 0
171 Program_Fail_Count -O--CK 100 100 001 - 0
172 Erase_Fail_Count -O--CK 100 100 001 - 0
173 Wear_Leveling_Count PO--CK 100 100 010 - 0
174 Unexpect_Power_Loss_Ct -O--CK 100 100 001 - 398
181 Non4k_Aligned_Access -O---K 100 100 001 - 144 45 99
183 SATA_Iface_Downshift -O--CK 100 100 001 - 0
184 End-to-End_Error PO--CK 100 100 050 - 0
187 Reported_Uncorrect -O--CK 100 100 001 - 0
188 Command_Timeout -O--CK 100 100 001 - 0
189 Factory_Bad_Block_Ct -OSR-- 100 100 001 - 215
194 Temperature_Celsius -O---K 100 100 000 - 0
195 Hardware_ECC_Recovered -O-RCK 100 100 001 - 0
196 Reallocated_Event_Count -O--CK 100 100 001 - 0
197 Current_Pending_Sector -O--CK 100 100 001 - 0
198 Offline_Uncorrectable ----CK 100 100 001 - 0
199 UDMA_CRC_Error_Count -O--CK 100 100 001 - 0
202 Perc_Rated_Life_Used ---RC- 100 100 001 - 0
206 Write_Error_Rate -OSR-- 100 100 001 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
Read SMART Log Directory failed: scsi error medium or hardware error (serious)
General Purpose Log Directory Version 1
Address Access R/W Size Description
0x00 GPL R/O 1 Log Directory
0x03 GPL R/O 16383 Ext. Comprehensive SMART error log
0x04 GPL R/O 255 Device Statistics log
0x07 GPL R/O 3449 Extended self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x80-0x9f GPL R/W 16 Host vendor specific log
0xa0 GPL VS 2000 Device vendor specific log
0xa1-0xbf GPL VS 1 Device vendor specific log
0xc0 GPL VS 80 Device vendor specific log
0xc1-0xdf GPL VS 1 Device vendor specific log
0xe0 GPL R/W 1 SCT Command/Status
0xe1 GPL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (16383 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (3449 sectors)
Read SMART Selective Self-test Log failed: scsi error medium or
hardware error (serious)
SCT Status Version: 3
SCT Version (vendor specific): 1 (0x0001)
SCT Support Level: 0
Device State: Stand-by (1)
Current Temperature: 0 Celsius
Power Cycle Max Temperature: 0 Celsius
Lifetime Max Temperature: 0 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 10 minutes
Temperature Logging Interval: 10 minutes
Min/Max recommended Temperature: 0/70 Celsius
Min/Max Temperature Limit: -5/75 Celsius
Temperature History Size (Index): 478 (40)
Index Estimated Time Temperature Celsius
41 2014-08-13 15:10 ? -
... ..(473 skipped). .. -
37 2014-08-16 22:10 ? -
38 2014-08-16 22:20 0 -
39 2014-08-16 22:30 0 -
40 2014-08-16 22:40 0 -
Write SCT (Get) Error Recovery Control Command failed: scsi error
medium or hardware error (serious)
SCT (Get) Error Recovery Control command failed
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 2) ==
1 0x008 4 515 Lifetime Power-On Resets
1 0x010 4 4440 Power-on Hours
1 0x018 6 933634265 Logical Sectors Written
1 0x020 6 2708986 Number of Write Commands
1 0x028 6 852431906 Logical Sectors Read
1 0x030 6 6049196 Number of Read Commands
4 ===== = = == General Errors Statistics (rev 1) ==
4 0x008 4 0 Number of Reported Uncorrectable Errors
4 0x010 4 0 Resets Between Cmd Acceptance and Completion
5 ===== = = == Temperature Statistics (rev 1) ==
5 0x008 1 0 Current Temperature
5 0x010 1 0 Average Short Term Temperature
5 0x018 1 0 Average Long Term Temperature
5 0x020 1 0 Highest Temperature
5 0x028 1 0 Lowest Temperature
5 0x030 1 0 Highest Average Short Term Temperature
5 0x038 1 0 Lowest Average Short Term Temperature
5 0x040 1 0 Highest Average Long Term Temperature
5 0x048 1 0 Lowest Average Long Term Temperature
5 0x050 4 - Time in Over-Temperature
5 0x058 1 70 Specified Maximum Operating Temperature
5 0x060 4 - Time in Under-Temperature
5 0x068 1 0 Specified Minimum Operating Temperature
6 ===== = = == Transport Statistics (rev 1) ==
6 0x008 4 0 Number of Hardware Resets
6 0x010 4 0 Number of ASR Events
6 0x018 4 0 Number of Interface CRC Errors
7 ===== = = == Solid State Device Statistics (rev 1) ==
7 0x008 1 21~ Percentage Used Endurance Indicator
|_ ~ normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
On 16 August 2014 20:06, Christian Franke <[email protected]> wrote:
> Mike wrote:
>>
>> Greetings
>>
>> Following on from previous message, where running smartctl with the
>> disk connected via SATA returns a 600PB disk (it is actually 512Gb
>> Crucial M4), I followed advice from the Crucial message boards and
>> left the disk idle over night in order to trigger automatic garbade
>> collection. No change the next morning, below is some smartctl
>> output. I've tried ddrescue to no avail, reads just fail completely.
>> ...
>>
>> smartctl 6.3 2014-07-26 r3976 [x86_64-linux-3.13.0-34-generic] (local
>> build)
>> Copyright (C) 2002-14, Bruce Allen, Christian Franke,
>> www.smartmontools.org
>>
>> === START OF INFORMATION SECTION ===
>> Model Family: Crucial/Micron RealSSD m4/C400/P400
>> Device Model: M4-CT512M4SSD1
>> ...
>>
>> Read SMART Log Directory failed: scsi error medium or hardware error
>> (serious)
>>
>
> This error message is probably due to a limitation/bug in driver/firmware of
> the used (which?) controller. The device itself should support SMART Log
> Directory.
>
>
>> General Purpose Log Directory Version 1
>> Address Access R/W Size Description
>> 0x00 GPL R/O 1 Log Directory
>> 0x03 GPL R/O 16383 Ext. Comprehensive SMART error log
>> 0x04 GPL R/O 255 Device Statistics log
>> 0x07 GPL R/O 3449 Extended self-test log
>> ..
>>
>> SMART Extended Comprehensive Error Log size 16383 not supported
>>
>> Read SMART Error Log failed: scsi error medium or hardware error (serious)
>>
>> SMART Extended Self-test Log size 3449 not supported
>>
>> Read SMART Self-test Log failed: scsi error medium or hardware error
>> (serious)
>
>
> The extended error/self-test logs may contain useful info. Unfortunately
> smartctl does not print the extended logs due to a historic size limitation.
> In the early days of these logs, sizes were <= 8.
>
> If possible, apply the attached patch and try whether the logs could be read
> then.
>
> Thanks,
> Christian
>
------------------------------------------------------------------------------