RE: configuration of addresses on ipsec0.

Yes, this might be a good first step, but look out for side-effects as it=
 might cause some problems, exchanging scripts between different versions=
 of FreeSWAN.
Alternativly, you could look for the few lines of code which do the addre=
ss assignment and copy them just over to your scripts.

Best Regards,

	Gerhard

--------------------------------------------
Gerhard Ge=DFler

Communication Networks, IABG mbH
Einsteinstr. 20
85521 Ottobrunn, Germany

Telefon: +49 89 6088 - 2021
Fax: +49 89 6088 - 2845

E-Mail: [email protected]=20

  > -----Original Message-----
  > From: Kaustubh Kumbhalkar=20
  > [mailto:[email protected]]=20
  > Sent: Thursday, April 10, 2003 11:06 AM
  > To: Gessler Gerhard; [email protected];=20
  > [email protected]
  > Subject: RE: [Users] configuration of addresses on ipsec0.
  >=20
  >=20
  > hi
  > iam using freeswan-1.91-v02 .and not the version with=20
  > U-1.99 and K-1.91 so i think i should be using _startklips=20
  > from the newer version.
  >=20
  >=20
  >=20
  >=20
  >=20
  > Thursday, 10 April 2003 2:33 PM
  > To: "Kaustubh Kumbhalkar" <[email protected]>,
  > <[email protected]>, <[email protected]>
  > cc:
  > From: "Gessler Gerhard" <[email protected]>
  > Subject: RE: [Users] configuration of addresses on ipsec0.
  >=20
  >=20
  >=20
  > Hi,
  >=20
  > as I know that you are dealing quite heavily with IPv6, I=20
  > assume that the question is IPv6 related, even if not=20
  > explicitly stated.
  >=20
  > What version of IPv6-enabled FreeSWAN do you use?
  > I know we had this effect in older verions, but if I am not=20
  > mistaken, we changed that in our later versions.
  >=20
  > Best Regards,
  >=20
  >  Gerhard
  >=20
  > --------------------------------------------
  > Gerhard Ge=DFler
  >=20
  > Communication Networks, IABG mbH
  > Einsteinstr. 20
  > 85521 Ottobrunn, Germany
  >=20
  > Telefon: +49 89 6088 - 2021
  > Fax: +49 89 6088 - 2845
  >=20
  > E-Mail: [email protected]
  >=20
  >   > -----Original Message-----
  >   > From: Kaustubh Kumbhalkar
  >   > [mailto:[email protected]]
  >   > Sent: Wednesday, April 09, 2003 7:03 AM
  >   > To: [email protected]; [email protected]
  >   > Subject: [Users] configuration of addresses on ipsec0.
  >   >
  >   >
  >   > hi
  >   > i am facing a problem w.r.t configuration of addresses on
  >   > ipsec0 dev. at the time i  give the command ipsec setup
  >   > start, there are multiple addresses configured on eth0
  >   > device. but pluto configures only one address on ipsec0
  >   > device which is the first address in the list. all the
  >   > addresses are valid globally routable unicast addresses.
  >   > another problem  is that when router advertisements are
  >   > recieved it configures the any new prefixes over ipsec0 and
  >   > not on eth0. what could be happening ?
  >   >
  >   > help pls
  >   >
  >   > kausty
  >   >
  >   > _______________________________________________
  >   > Users mailing list
  >   > [email protected]
  >   >   > http://lists.freeswan.org/mailman/listinfo/users
  >   >
  >=20
  >=20