Snapshot install on 715/100

Hello,

I try to install Openbsd on a HP 715/100 [1] with a serial console.
The netboot seems correct but fail on sti 0 (dmesg [2])
Standard Text Interface ?? It's the console?
The graphic card is not supported ?
I have test with boot -c and disable wsdisplay as i read on the list,
no success..
I verified the lif33.fs checksum and it's ok.

If the material is not supported, please excuse me.. I have read the
openbsd.org/hppa.html but i don't know very well this system.


Thank you in advance.


Footnotes: 
[1]  
,----
| BOOT_ADMIN> Information
| 
| System model number: HP 9000/715/100
| Processor revision 2.3  100MHz
| Instruction Cache Size:  131072
| Data Cache Size:         131072
| Memory Size:  96 MB
| Built in floating point coprocessor
| Board Serial Number 401102Q1A6
| 
| BootRom Version    1.3  
| 
| auto boot off
| auto search off
| fastboot off
| 
| Primary boot path:    scsi.6.0
| Alternate boot path:  lan.000000-000000.0.0
| Console path:         rs232.9600.8.none
| Keyboard path:        ps2
| 
| LAN Station Addresses: 080009-70954A
|                        080009-930717
`----


[2]  

,----
| [ bsd ELF symbol table not valid: symtab unaligned ]
| [ bsd symbol table has bad string table address 0x7fb3dc4a ]
| [ no symbol table formats found ]
| Copyright (c) 1982, 1986, 1989, 1991, 1993
| 	The Regents of the University of California.  All rights reserved.
| Copyright (c) 1995-2003 OpenBSD. All rights reserved.  http://www.OpenBSD.org
| 
| OpenBSD 3.3 (RAMDISK) #3: Tue Mar 25 14:25:03 EST 2003
|     [email protected]:/usr/obj/sys/arch/hppa/compile/RAMDISK
| HP9000/715/100 (Mirage Sr.) PA-RISC 1.1f
| real mem = 100663296 (262144 reserved for PROM, 8318976 used by OpenBSD)
| avail mem = 79532032
| using 8421 buffers containing 10035200 bytes of memory
| mainbus0 (root) [flex fff80000]
| pdc0 at mainbus0
| mem0 at mainbus0 offset ffbf000: viper rev 0, size 96MB
| cpu0 at mainbus0 offset ffbe000 irq 31: PCXL L1-A 100MHz, FPU PCXL (CMOS-26B) rev 1
| cpu0: 128K(32b/l) Icache, 128K(32b/l) wr-back coherent Dcache, 120 coherent TLB, 8 BTLB
| "WAX Bus Adapter" at mainbus0 (type b, sv 8e) offset 200000 not configured
| "WAX EISA Bus Adapter" at mainbus0 (type b, sv 90) offset c000000 not configured
| lasi0 at mainbus0 offset 100000 irq 28: rev 3.0
| gsc0 at lasi0: wordleds
| gsckbc0 at gsc0 offset 8100 irq 26
| gsckbc1 at gsc0 offset 8000 irq 26 (shared with gsckbc0)
| "floppy controller" at gsc0 (type a, sv 83) offset a000 not configured
| "Advanced audio (ext.)" at gsc0 (type a, sv 7b) offset 4000 not configured
| lpt0 at gsc0 offset 2000 irq 7
| com0 at gsc0 offset 5000 irq 5: ns16550a, 16 byte fifo
| com0: console
| ie0 at gsc0 offset 7000 irq 8: LASI/i82596CA v2.0, address 08:00:09:70:95:4a
| osiop0 at gsc0 offset 6000 irq 9: NCR53C710 rev 2, 40MHz, SCSI ID 7
| osiop0: resetting chip
| scsibus0 at osiop0: 8 targets
| osiop0: target 2 now using 8 bit 4 MHz 8 REQ/ACK offset xfers
| cd0 at scsibus0 targ 2 lun 0: <TOSHIBA, CD-ROM XM-3401TA, 1094> SCSI2 5/cdrom removable
| osiop0: target 4 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
| sd0 at scsibus0 targ 4 lun 0: <SEAGATE, ST32151N, 0530> SCSI2 0/direct fixed
| sd0: 2049MB, 4177 cyl, 8 head, 125 sec, 512 bytes/sec, 4197405 sec total
| osiop0: target 6 now using 8 bit 10 MHz 8 REQ/ACK offset xfers
| sd1 at scsibus0 targ 6 lun 0: <QUANTUM, LPS525S, 3110> SCSI2 0/direct fixed
| sd1: 499MB, 2448 cyl, 6 head, 69 sec, 512 bytes/sec, 1023484 sec total
| sti: hpa=f8000000, rom=f0025000
| sti: ioh=f8000000, romh=f0025000
| sti: devtype=3
| sti0 at mainbus0 offset 8000000 irq 11sti: hpa=f8000000, rom=f0025000
| sti: ioh=f8000000, romh=f0025000
| dd:
| devtype=3, rev=84;5, gid=2b4d, font=35d4, mss=1b
| end=45e5, mmap=35c0, msto=0, timo=250, mont=c0, ua=128
| memrq=100, pwr=312, bus=0, ebus=0, altt=0, cfb=0
| code=608,1dc4,2048,25d4,2920,309c,31a8,342c,35c0,0,0,0,0,0,0,0
| code=0xe2ea0000[2fb8]
| stiregions @0x35c0:
| 6000 @ 0xf0025000 btlb
| 1000000 @ 0xf9000000 btlb
| 280000 @ 0xf8100000 btlb
| already mapped region
| 1000 @ 0xf8380000 sys last
| already mapped region
| sti0: init,0xe2ea0000(86000000, 0x6f1910, 0x6f1918, 0xc01bef24)
| sti0: init,0xe2ea0000(a6380000, 0x6f1910, 0x6f1918, 0xc01bef24)
| : HPA208LC1280 rev 8.04;5
| sti0: 2048x1024 frame buffer, 1280x1024x8 display, offset 0x0
| sti0: 8x16 font type 1, 16 bpc, charset 0-255
| biomask 0x7 netmask 0xf ttymask 0x3f
| panic: trap: uvm_fault(0x693960, f00e0000, 0, 2): 14
| Stopped at      0x173508:       break   0,5
| RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
| DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
| ddb> trace
| (null)(192aec,f0105800,5,6e7800) at 0x173508
| (null)(1ba830,693960,f00e0000,0) at 0x83608
| (null)(6f1388,68ee90,169170,6f1448) at 0x835ec
| (null)(0,0,169170,68ee78) at 0x17cdf0
| -- trap #15
| (null)(0,0,0,0) at 0x16ed90
| (null)(1b5234,fff80000,6f1308,6aaf88) at 0x4bd68
| (null)(0,0,ffffffff,ffffff) at 0x4bd68
| (null)(336600,0,40089c,c01b7fc0) at 0x17d9b0
| (null)(0,0,6f1408,2) at 0x17ce24
| -- trap #4
| (null)(18f4f4,f0105800,5,6e7800) at 0x171ef0
| (null)(0,0,0,0) at 0x171ee4
| (null)(0,0,0,0) at 0x680f8
| -- trap #0
| 0x40154:
| ddb> ps
|    PID   PPID   PGRP    UID  S       FLAGS  WAIT       COMMAND
| *    0     -1      0      0  2     0x80204             swapper
`----



-- 
 \|/ ____ \|/                                            .    
 "@'/ , .\`@"  Thomas Montfort                          °v°
 /_| \__/ |_\  31400 Toulouse - France                  ` /
    \__U_/                                              v_v